Yamaha CRX-E300 Service Manual page 36

CRX-E300
QQ
3 7 63 1515 0
IC406: MN35511AL (CD P.C.B.)
Signal Processor & Controller
Pin No. Name I/O
1 BCLK O
LRCK
2 O
SRDATA O
3
4 DVDD1 I
5 DVSS1 I
TX O
6
7 MCLK I
8 MDATA I
MLD
9 I
SENSE O
10
11 FLOCK O
12 TLOCK O
BLKCK
13 O
14 SQCK I
15 SUBQ O
DMUTE
16 I
STAT O
17
18 RST I
19 SMCK/ O
FCLK
20 CLVS/ O
FLAG6
TRV
21 O
TVD O
22
TE
L 13942296513
23 PC O
24 ECM O
ECS
25 O
KICK O
26
27 TRD O
FOD
28 O
VREF I
29
30 FBAL O
31 TBAL O
FE
32 I
TE I
33
34 RFENV I
VDET
35 I
OFT
36 I
37 TRCRS I
38 RFDET I
BDO
39 I
LDON O
40
41 TOFS O
PLAY/TRVSTOP
42 O
WVEL
43 O
44 ARF I
45 IREF I
DRF
46 I
www
(Note 1) At the SMCK/FCLK pin, output does not stop while /RST=L.
.
36
http://www.xiaoyu163.com
Bit clock output for SR DATA
L/R identification signal output
Serial data output
Power supply for digital circuit
GND for digital circuit
Digital, audio, interface output signal
Microprocessor command clock signal input (data latched at leading edge)
Microprocessor command data input
Microprocessor command load signal input
Sense signal output (OFT, FESL, NACEND, NAJEND, SFG, NWTEND)
Focus servo drawing signal (L : when drawn)
Tracking servo drawing signal (L : when drawn)
Sub code block clock signal (BLKCK=75Hz)
Clock input for sub-code Q register
Sub-code Q code output
Muting input (H : MUTE)
Status signal (CRC, STCNT, CLVS, TTSTOP, SQOK, RESY, FCLV, FLAG6, SENSE ,/FLOCK, /RFDET, /TLOCK)
Reset input (L : RESET)
4.2336MHz clock signal output SMCK when command is defaulted. (Note 1)
SMCK (8.4672MHz), FCLK (7.35kHz) or "L" fixed is selected when command is switched.
With command defaulted : CLVS when IOSEL=H, FLAG6 when IOSEL=L
These settings can be reversed by command (FLAG6 when IOSEL=H).
Traverse (Feed) forced feed output
Traverse (Feed) drive output
Spindle motor ON signal L : ON (default)
Spindle motor drive signal (forced mode output)
Spindle motor drive signal (servo error signal output)
Kick pulse output 3-State
Tracking drive output
Focus drive output
Reference voltage for DA output block (TVD, ECS, TRD, FOD, FBAL, TBAL)
Focus balance adjustment output
Tracking balance adjustment output
Focus error signal input (analog input)
Tracking error signal input (analog input)
RF envelope signal input (analog input)
Oscillation detect signal input (H : DETECT)
Off track signal input (H : OFF TRACK)
Track cross signal input (analog input)
RF detect signal input (L : DETECT)
Drop out signal input (H : DROP OUT)
Laser ON signal output (H : ON)
Tracking offset adjustment output
Switched by command. PLAY (Play signal output) when command is defaulted.
Double speed status signal output (H : double speed)
RF signal input
Reference current input terminal
Bias terminal for DSL
x ao
y
i
http://www.xiaoyu163.com
8
Function
(L : LOAD)
3-State
Q Q
3 6 7 1 3
3-State
u163
.
2 9 9 4 2 8
1 5 0 5 8 2 9 9 4
m
co
9 9
(NC)
(NC)
(NC)
(+5)
(GND)
(NC)
(NC)
2 8 9 9
(NC)
(GND)
(NC)
(NC)
(NC)
(NC)