Operating Modes (Configurations); Selecting A Configuration - Behringer X V-AMP User Manual

2 FUNCTION. As soon as any second-layer function on
nd
the FX/AMPS control is dialed up, 2
up.
FX/AMPS. A LED on the FX/AMPS control indicates the
current AMP model. If the 2
you’re dealing with one of the second-layer AMP models
(gray); if not, then one of the first-layer AMP models is
selected (white). By turning FX/AMPS (and by holding tap,
if necessary), you can switch to another AMP model.
IF the effect block is selected (MODULATION
or REVERB LED
type can be read-off and selected using the FX/AMPS
control. By turning the FX/AMPS control (and by holding
TAP, if necessary), you can switch to another effect.
+
+
The DISPLAY indicates which preset has been selected
and gives information on the modifications done during
editing. When the TUNER is activated, the DISPLAY indi-
cates which tone is played on the instrument you connected
to your X V-AMP.
Fig. 2.1: X V-AMP display
DOWN. Use this footswitch to dial down presets (99 - 00,
downwards). Keep the footswitch depressed longer to
skip through the presets downwards.
UP. Use this footswitch to dial up presets (00 - 99, upwards).
Keep the footswitch depressed longer to skip through the
presets upwards.
+
EXPRESSION PEDAL. The expression pedal controls
(among others) the Wah Wah effect. The switch located
beneath the pedal switches the Wah Wah on and off in this
case.
PEDAL ASSIGN lets you assign another function to the
pedal (e. g. volume, effect intensity etc.). See also
LINE OUT/PHONES. You can take the audio signal of
your X V-AMP at the LINE OUT/PHONES connector. You
can either connect your headphones to the X V-AMP, or
connect the X V-AMP to a mixer.
MONO AMP OUT. Connect the input of your guitar amp
here. In contrast to the LINE OUT/PHONES signal, this
signal is reproduced with a level that is 20 dB lower.
INSTRUMENT INPUT. This is the 1/4" jack input of your
X V-AMP. Connect your instrument here. Always use high-
quality 1/4" mono jack cables.
AC IN. Connect the enclosed power supply to the AC IN
connector. As soon as you plug the power supply into the
mains, your X V-AMP is automatically “on”. More information
on the power supply can be found in chapter 9
“SPECIFICATIONS”.
nd FUNCTION LED lights
nd FUNCTION LED is also lit up,
, DELAY
blinks), the respective effect
.

3. OPERATING MODES (CONFIGURATIONS)

SERIAL NUMBER.
3. OPERATING MODES
(CONFIGURATIONS)
An outstanding characteristic of the entire V-AMP product line
is the freedom to personally select which signal segments
(according to your own needs and desires) will be fed to the
outputs. To optimally adjust your X V-AMP to various studio and
live situations, you can select one of the 9 possible configurations.
These configurations assign where individual signals for line
outputs and headphone outputs are coming from—and all this
independent from the settings stored in the presets.

3.1 Selecting a CONFIGURATION

When you press NOISE GATE
the same time, CONFIGURATION mode is activated or
deactivated. The key LEDs are blinking as long as you are in
CONFIGURATION mode.
Dialing up individual configurations in CONFIGURATION mode
is done by using NOISE G.
the respective configurations is shown below.
Volume is adjustable globally by using the ADJUST control.
Input gain can be adjusted using ADJUST + TAP, so that you
can adjust your X V-AMP globally to instruments with varying
output signal levels, whereby the following goes: a higher setting
is for quieter instruments, and a lower setting is for louder
instruments.
P @S6UDIBÃHP9@ YÃW6H Ã8PIADBVS6UDPI
A 6U)Ã
QCPI@T
Neutral EQ
(with all
!
PV9I@TT)Ã
speaker and
amp
QS@T@I8@)Ã
"
simulations
bass tones
6
A 6U)Ã
Neutral EQ
6HQÃÃAY
6!
(without PV9I@TT)Ã
speaker
QS@T@I8@)Ã
simulations)
6"
bass tones
A
A 6U)Ã
y’ÃAY
Neutral EQ
(without
A!
PV9I@TT)Ã
speaker and
amp
QS@T@I8@)Ã
A"
simulations)
bass tones
Tab. 3.1: Operating modes (CONFIGURATIONS)
X V-AMP
and COMPRESSOR at
and COMPR. . A table with
Increasing bass and highs
Accentuation of upper mids, lowering of
Increasing bass and highs
Accentuation of upper mids, lowering of
Increasing bass and highs
Accentuation of upper mids, lowering of
7