Table of Contents
Advertisement
Section 4: Maintenance & Lubrication
Wing Skid Shoe
Refer to Figure 4-8:
Replace wing skid shoes as follows:
1. Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2)
and wing skid shoe (#1) as shown.
2. Plow bolts (#2) should be checked for wear and
replaced if necessary.
3. Attach new skid shoe (#1) to cutter with existing
3/8" plow bolts (#2) and secure with 3/8" hex whiz
nuts. Torque to 31 ft. lbs.
4. Repeat on opposite wing section.
Wing Skid shoe
Figure 4-8
Weight Box Skid Shoe
Refer to Figure 4-8:
Replace wing skid shoes as follows:
1. Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2)
and wing skid shoe (#1) as shown.
2. Plow bolts (#2) should be checked for wear and
replaced if necessary.
3. Attach new skid shoe (#1) to cutter with existing
3/8" plow bolts (#2) and secure with 3/8" hex whiz
nuts. Torque to 31 ft. lbs.
23569
Wing Skid shoe
Figure 4-9
28
RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M
Table of Contents
Tractor Maintenance
One of the most important things you can do to prevent
hydraulic system problems is to ensure that your tractor's
reservoir remains free of dirt and contamination.
Use a clean cloth to wipe the hose ends before attaching
them to your tractor. Replace the filter element for your
tractor's hydraulic system at the prescribed intervals.
These simple maintenances will go a long way to prevent
the occurrence of control valve and hydraulic cylinder
problems.
Storage
It is good practice to clean, inspect, service and make
necessary repairs to the cutter when parking it for long
periods and when parking it at the end of a working
season. This will help ensure the cuter is ready for field
use the next time you hook-up to it.
!
Always disconnect main driveline from tractor PTO and secure
cutter deck in the up position with solid supports before
servicing the underside of the cutter.
1. Clean off any dirt and grease that may have
Skid shoe
is reversible
22173
2. Check blades and blade bolts for wear and replace if
3. Inspect for loose, damaged or worn parts and adjust
4. Lubricate as noted in "Lubrication Points" starting on
5. Replace all damaged or missing decals.
6. Store cutter on a level surface in a clean, dry place.
7. Follow all unhooking instructions on page 16 when
8. Repaint parts where paint is worn or scratched to
Part No.
821-011C
Skid shoe
821-002C
is reversible
821-054C
821-058C
DANGER!
accumulated on the cutter and moving parts. Scrape
off compacted dirt from the bottom of deck and then
wash surface thoroughly with a garden hose. A
coating of oil may also be applied to the lower deck
area to minimize oxidation.
necessary. See "Cutter Blade Maintenance" on
page 22.
or replace as needed.
page 29.
Inside storage will reduce maintenance and make for
a longer cutter life.
disconnecting tractor from cutter.
prevent rust. Ask your dealer for Aerosol Land Pride
touch-up paint. They are also available in touch-up
bottles with brush, quarts and gallon sizes by adding
TU, QT or GL to the end of the Aerosol part number.
Land Pride Touch-up Paint
Part Description
PAINT LP BEIGE SPRAY CAN
PAINT LP BLACK SPRAY CAN
PAINT MEDIUM RED SPRAY CAN
PAINT GREEN SPRAY CAN
Land Pride
9/04/08
Advertisement
Table of Contents
