Cleaner Maintenance; Emptying The Dust Container; Removing A Blockage - Hoover Vacuum Cleaner User Manual

All accessories can be fitted to the end of the handle or the end of the tube.
2 in 1 Accessory
Remove the 2in1 accessory from the rear of the cleaner [12] and fit onto the end of the
handle. [13]
Crevice Tool – For corners and hard to reach areas. [1U]
dusting brush – For bookshelves, frames, keyboards and other delicate areas. To
extend the brushes push the button on the body of the tool. [1U]
Pet Hair Remover mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [1V]
Allergen Remover mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for
deep cleaning on textile surfaces and other hard to clean areas, particularly suitable for
allergen removal. [1w]
Grand Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1X]
Hard Floor Caresse Nozzle* – For parquet floors and other delicate floors. [1y]
ImPORTANT: Do not use the Grand turbo and mini turbo nozzles on rugs with long
fringes, animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary
while the brush is rotating.

ClEANER mAINTENANCE

Emptying the dust Container

When the dust reaches the max level indicator in the container, empty the dust container.
ImPORTANT: To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Release the Dust Container by pressing the Dust Container Release Button. Lift the
Dust Container from the cleaner mainbody. [14]
2. Hold the Dust Container over a bin with one hand, and remove the Dust container
lid by rotating anti-clockwise. [15]
Empty the dust from the bin. [16]
3.
4. Close and refit the dust container to the cleaner.
Cleaning the washable filters
The cleaner is fitted with pre motor filter and exhaust filter. To maintain optimum cleaning
performance, regularly remove the filter and tap against the side of the bin to release dust.The
filters should be washed every 5 container empties or when the filter has excessive dust level.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean
*Certain models Only ** Certain models only, nozzles may vary according to model
your filters may result in air blockage, overheating and product failure. This may
invalidate your guarantee.
ImPORTANT: Regularly check and maintain the filters.
ImPORTANT: Always ensure the filter pack is fully dry before use.
To access the Pre-Motor filter:
Remove the dust Container from the cleaner mainbody. [14]
1.
2. Hold the Dust Container over a bin with one hand, and remove the bin lid by rotating
anti-clockwise. [15]
3. Remove the filter mesh* by rotating clockwise from bin lid. [17]
4. Remove the pre-motor filter by rotating clockwise from bin lid. [18]
5. Gently tap and wash the filter mesh* and filter, do not use hot water or detergents.
[19] Remove excess water from the filter mesh* and filter and leave to dry fully
before re-using. [22]
6. Reassemble the pre-motor filter pack (filter mesh* and filter) once fully dry and refit
to the cleaner.
To access the exhaust filter:
1. Press the exhaust filter grid latch to access to the exhaust filter from rear of the
cleaner. [20]
2. Remove the exhaust filter from the grid. [21]
3. Gently tap and wash the exhaust filter, do not use hot water or detergents. Remove
excess water from the exhaust filter and leave to dry fully before re-using. [22]
4. Refit the exhaust filter to grid once fully dry and refit the exhaust grid.
ImPORTANT: Do not use the product without the exhaust filter fitted.

Removing a blockage

1. Check if the dust container is full. If so refer to 'Emptying the dust container'.
2. If the dust container is empty but suction is still low:
A. Do the filters need cleaning? If so refer to 'Cleaning the washable filters'.
B. Check if there is any other blockage in the system - Use a rod or pole to remove
any blockage from the extension tube or flexible hose.
C. Check if pre-motor filter is fitted and filter door is closed
warning*-. If the cleaner is used for a significant period of time when dust container is
full, filters are dirty and with a blockage in the system, a thermal cut out will switch the
cleaner off to prevent overheating. If this should happen, switch the cleaner off, unplug
and correct the fault. It will take about 30 minutes for the cut out to automatically reset.
3