Table of Contents
Advertisement
OPERATING FIREPLACE
INSERT
Continued
WARNING: Make sure the selector switch is in the
OFF position when you are away from home for long
periods of time. Heater will come on automatically
with selector switch in the ON position.
Ignitor
Pilot Burner
Electrode
Natural Gas
Figure 34 - Pilot
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
1. Turn control knob clockwise
2a. Set selector switch in the OFF position.
2b. If Using Optional Hand-Held Remote: Set remote selector
switch in the OFF position to keep from draining battery.
Shutting Off Burners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one
of the following:
• Turn control knob clockwise
• Use remote control manual OFF button.
• Set remote selector switch in the OFF position.
MANUAL LIGHTING
PROCEDURE
1.
Follow steps 1 through 6 under Lighting Instructions, page 16.
2. Depress control knob and light pilot with match.
3. Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob. Now follow
steps 9 through 11, page 16.
OPTIONAL REMOTE
OPERATION
Note: All remote control accessories must be purchased sepa-
rately (see Accessories, page 28). Follow instructions included
with the remote control.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
111285-01A
Pilot Burner
Ignitor
Electrode
Propane/LP Gas
to the OFF position.
to the PILOT position.
OPERATING FIREPLACE INSERT
Lighting Instructions (Cont.)
To Turn Off Gas To Appliance
Manual Lighting Procedure
Optional Remote Operation
Thermostat Control Operation
(Optional GHRCTA Series Only) The thermostat control set-
ting on the remote control unit can be set to any comfort level
between WARMER and COOLER. The burners will turn on
and off automatically to maintain the comfort level you select.
The ideal comfort setting will vary by household depending
upon the amount of space to be heated, the output of the central
heating system, etc.
For wall thermostat operation, follow instruction supplied with
thermostat accessory GWMT1. For wall switch operation fol-
low instructions supplied with GWMS2.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See Lighting Instruc-
tions on page 16.
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjust-
ment knob anywhere between HI and LO. Slide the remote
selector switch to the REMOTE position (see Figure 35,
page 18). Note: The burners may light if hand-held remote
ON button was on when remote selector switch was last
turned off. You can now turn the burners on and off with
the hand-held remote control unit.
IMPORTANT : Do not leave the remote selector switch in
the REMOTE position when the pilot is not lit. This will
drain the battery.
IMPORTANT: Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
GHRC Series Operation:
2a. Press the ON/OFF button to turn the burner on and off.
When turning burner off, the pilot will remain lit.
GHRCTA Series Operation:
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 36, page 18). The lights to the left of the
button will show AUTO, ON, or OFF.
• In the ON mode, the burners will ignite. The heater is in
manual mode when ON is lit.
• In the AUTO mode, the thermostat in the hand-held re-
mote unit controls the room temperature. To increase the
room temperature, press the top arrow of the TEMP but-
ton. To lower the room temperature, press the bottom
arrow of the TEMP button. At higher settings the heater
will run longer.
17
17
Advertisement
Table of Contents
