6-Disc FM Modulator CD Changer For Use With Any FM Vehicle Radio Changeur de CD/modulateur FM & 6 disques Cambiador de Discos Compactos Para 6 Discos y Modulador de FM Para Uso con Cualquier Radio FM de Vehiculo Cambiador CD para 6 discos corn Modulador FM para uso corn qualquer Rtidio FM de Bosch Group...
Owner’s Record The model and warranty numbers are located on the rear of the unit. Record the warranty in the space provided below. Refer to these numbers whenever you call upon your Blaupunkt dealer regarding this product. Model No. CDC-RF6...
Table of Contents Before installing and operating this unit, please Antes de instalar y operar esta unidad, por favor read this manual thoroughly and retain it for lea este manual detenidamente y guardelo para future reference. referencia en el futuro. English lndice Owners’s Record ..........
- please carefully follow all of the instructions. You’ll be glad you did! General Recommendations If you’re not confident that you can install the unit correctly, have it installed by a qualified Blaupunkt installation technician. Design and specifications subject to change without notice.
4. After disconnecting and reconnecting the car battery, etc. ID (Identity) Switch for 2nd CD Changer To connect a second CDC-RF 6 changer, you must use Blaupunkt’s CDC-RF BRIDGE, which is sold separately. When an additional CD changer has been connected...
Electrical Connections Electrical Connections Caution: before making connections, disconnect the ground wire terminal of the car battery to avoid short circuits. Use this unit only with negative ground 12 Volt (1 16 Volt) direct current (DC). Be sure to use the supplied changer cord. Using a cord other than the one supplied may cause noise or damage.
Commander (See page 5). If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer. Be sure to remove the transport screws (See page 5).
Page 8
Horizontal Installation Confirm that Anti-Vibration Anti-Vibration S w i t c h e s 1111~ Switches on both left and right sides are set to position H. Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8). Attach brackets (L) and (R) to their respective brackets (5) using tha...
Page 9
Vertical Installation Confirm that Anti-Vibration Switches on both left and right sides are set to position V. Attach brackets (L) and (R) using the hexagonal bolts Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (M6).
Page 10
Confirm that Anti-Vibration Switches on both left and right sides are set to position 45”. Attach brackets (L) and (R) using the hexagonal bolts (M5 x 8). Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (M6).
Page 11
Suspended Installation Make sure that the unit does not hinder the Anti-Vibration movement of torsion bar spring or other parts of the trunk lid. Confirm Anti-Vibration Switches on both the left and right sides are set to position “HI’. Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8).
Installation of the FM Modulator Install the FM Modulator to the floor or other surface with the included tapping screws (M3x12). FM Modulator Changer Specifications System Compact disc digital audio system Oversampling 1 -Bit/8 X Oversampling Laser Diode Frequency response 20-l 5,000 Hz +/- 3 dB Wow and Flutter Below Measurable limit...
DIGITAL AUDIO Do not use 3” (8cm) discs with the CDC-RF6. Handle the disc by its edge, and to keep the disc clean, do not touch the surface. Do not leave the discs or the magazine in locations with high temperatures and high humidity, such as on a car dashboard or at the rear window where they will be subjected to direct sunlight or near heat ducts.
Magazine & Compact Discs Installing The Magazine 1. Slide the door toward the right. 2. Position the magazine so the top is facing up, and the arrow is facing the changer. Push it in until it clicks into place. Note: When the magazine is used for the first time, it will not lock into place unless the power supply has been connected.
Operating Instructions Before operating the unit for the first time (or after reconnecting the battery, etc.) press the Reset Button on the Commander. See page 5. Load the discs into the CD magazine and install the magazine into the CD charger. Turning Unit On/Playing A CD Vehicle ignition must be on.
Switching T A Second CD Changer If the CDC-RF BRIDGE (sold separately) is used, this CD changer system can accommodate an additional CDC-RF6 Changer. When two CD changers have been installed, the Changer Select Button used (8) is to select the desired changer. This button is not operational when only one CD changer has been connected.
The following check will assist in the correction of most problems that you might encounter with your unit. Perform the checks described below before contacting your Blaupunkt dealer. Symptom Cause Remedy Replace with a fuse of the same type No Power Fuse blown.
Error Codes If the changer malfunctions, one of the following error codes will be displayed: Error Display Cause Remedy Disc change malfunction. Consult with dealer..I 1.1.. Disc loaded with print facing up Load disc properly.
. BLAUPUNKT Bosch Group Robert Bosch Corporation Sales Group-Mobile Communications Division 2800 South 25th Avenue, Broadview, Illinois 60153 Printed in Japan 1 RAGPlOA71600...