Entering The Simulation Mode; Simulations - Toshiba e-STUDIO161 Service Manual

[7] SIMULATIONS

1. Entering the simulation mode

Perform the following procedure to enter the simulation mode.
"C" key AUTO/TEXT/PHOTO key
"C" key AUTO/TEXT/PHOTO key
Main code Start key Sub code
(Note:Perform the first four key strokes quickly allowing no more than one
second between key strokes.)
2. Canceling the simulation mode
When the clear all key is pressed, the simulation mode is cancelled.
When the interruption key is pressed, the process is interrupted and the
screen returns to the sub code entering display.
* After canceling the simulation mode, be sure to turn OFF/ON the
power and check the operation.
Note:If the machine is terminated by a jam error or paper empty during
copying in the adjustment by the simulation, recopying is required.
3. List of simulations
Main Sub
code code
01 01 Mirror scanning operation
02 Mirror home position sensor (MHPS) status display
06 Mirror scanning operation aging
02 01 Auto document feeder (ADF) aging
02 ADF sensor status display
03 ADF motor operation check
08 ADF paper feed solenoid operation check
11 ADF PS release solenoid operation check
05 01 Operation panel display check
02 Fusing lamp and cooling fan operation check
03 Copy lamp lighting check
06 01 Paper feed solenoid operation check
02 Resist roller solenoid operation check
10 Cassette semi-circular roller cleaning
07 01 Warm-up display and aging with jam
06 Intermittent aging
08 Shifting with warm-up display
08 01 Developing bias output
02 Main charger output (Grid = HIGH)
03 Main charger output (Grid = LOW)
06 Transfer charger output
10 - Toner motor operation
14 - Trouble cancel (except for U2)
16 - U2 trouble cancel
20 01 Maintenance counter clear
21 01 Maintenance cycle setting
02 Mini maintenance cycle setting
22 01 Maintenance counter display
02 Maintenance preset display
03 Jam memory display
04 Jam total counter display
05 Total counter display
06 Developing counter display
07 Mini maintenance preset display
08 ADF counter display
09 Paper feed counter display
12 Drum counter display
13 CRUM type display
14 P-ROM version display
15 Trouble memory display
17 Copy counter display
18 Printer counter display
21 Scanner counter display
22 ADF jam counter display
e-STUDIO161 SIMULATIONS
Start key
Contents
Main Sub
code code
24 01 Jam total counter clear
02 Trouble memory clear
04 ADF counter clear
06 Paper feed counter clear
07 Drum counter clear
08 Copy counter clear
09 Printer counter clear
13 Scanner counter clear
14 ADF jam total counter clear
15 Scanner mode counter clear
25 01 Main motor operation check
10 Polygon motor operation check
26 02 Size setting
05 Count mode setting
06 Destination setting
07 Machine condition check (CPM)
18 Toner save mode setting
30 CE mark conformity control ON/OFF
36 Cancel of stop at maintenance life over
37 Cancel of stop at developer life over
38 Cancel of stop at drum life over
39 Memory capacity check
42 Transfer ON/OFF timing control setting
43 Side void amount setting
51 Copy temporary stop function setting
30 01 Paper sensor status display
42 01 Developing counter clear
43 01 Fusing temperature setting
12 Standby mode fusing fan rotation setting
13 Fusing paper interval control allow/inhibit setting
44 34 Transfer current setting
40 Setting of rotation time before toner supply
46 01 Copy density adjustment (300dpi)
02 Copy density adjustment (600dpi)
09 Copy exposure level adjustment, individual setting
(Text) 300dpi
10 Copy exposure level adjustment, individual setting
(Text) 600dpi
11 Copy exposure level adjustment, individual setting
(Photo) 600dpi
18 Image contrast adjustment (300dpi)
19 Exposure mode setting
(Gamma table setting/AE operation mode setting/
Photo image process setting)
20 ADF exposure correction
29 Image contrast adjustment (600dpi)
30 AE limit setting
31 Image sharpness adjustment
48 01 Main/sub scanning magnification ratio adjustment
05 ADF mode sub scanning magnification ratio
adjustment in copying
49 01 Flash ROM program writing mode
12 Standby mode fusing fan RPM setting
50 01 Image lead edge adjustment
06 Copy lead edge position adjustment (ADF)
10 Paper off-center adjustment
12 Document off-center adjustment
51 02 Resist amount adjustment
53 08 ADF scanning position automatic adjustment
61 03 HSYNC output check
63 01 Shading check
07 ADDF automatic correction
64 01 Self print
7-1
Contents