Sony HCD-TZ100 Service Manual page 17

60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can't buffering
81: Unknown media type
7-4-1. Clear the Laser Hour
Press [ DISPLAY] button and then press [CLEAR] button on the
remote commander. The data for both CD and DVD data are reset.
Emg. History Check
Laser Hours CD
DVD
01. 01 05 04 04
00 00 00 00
02. 02 02 01 01
00 00 00 00
[Next] Next Page [Prev] Prev Page
[O] Return to Top Menu
7-4-2. Clear the Emergency History
Press [DVD TOP MENU] button and then press [CLEAR] button
on the remote commander. The error code for all emergency history
would be reset.
Emg. History Check
Laser Hours CD
DVD
01. 00 00 00 00
00 00 00 00
02. 00 00 00 00
00 00 00 00
[Next] Next Page [Prev] Prev Page
[O] Return to Top Menu
7-4-3. Clear the Initialize Setup Data
Press [DVD MENU] button and then press [CLEAR] button on the
remote commander.
Emg. History Check
Laser Hours CD
DVD
initialize setup data...
[Next] Next Page [Prev] Prev Page
[O] Return to Top Menu
0h 0min
0h 0min
00 92 46 00
00 00 23 45
00 A9 4B 00
00 00 23 45
999h 59min
999h 59min
00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
999h 59min
999h 59min
HCD-TZ100/TZ200/TZ300
7-4-4. Return to the Top Menu of Remocon Diagnosis
Menu
Press [0] button on the remote commander.
7-5. CHECK VERSION INFORMATION
To check the version information, please follow the following
procedure.
(1) From the Top Menu of Remocon Diagnosis Menu, select "4.
Version Information" by pressing the [4] button on the remote
commander. The following screen appears on the on-screen
display.
Version information
Firm (Main) : Ver. xxxxx
Firm (Sub) : xxxxx
RISC : xxxxx
8032 : xxxxx
Audio DSP : xxxxx
Servo DSP : xxxxx
Phy,Adr, : F,F,F,F,
[O] Return to Top Menu
To return to the Top Menu of Remocon Diagnosis Menu, press
[0] button on the remote commander.
8. AMP TEST MODE
• This mode is used to measurement and test of the AMP con-
nection.
Procedure:
1. Press the [ ] button to turn the power on.
?/1
2. Press three buttons [ ], [
x
the this mode, blink to segments ("SA-CD" and "CAT") on FL
display.
3. Press [DISPLAY] button of the remote commander. When the
this mode is displayed as "MEASURE" on FL display.
Whenever the [DISPLAY] button is pressed, the AMP test
mode changes in the following order.
MEASURE t SAFETY
MEASURE: AMP measurement mode
SAFETY: AMP regulations, temperature, character mode
4. Press [MUTING] button on the remote commander. When the
this mode is displayed as "VOL N" on FL display.
Whenever the [MUTING] button is pressed, the VOL test
mode changes in the following order.
VOL N t VOL M/M
VOL N: Turn the [VOLUME] control, the display is
change in succession (MIN y MAX)
VOL M/M: Turn the [VOLUME] control in the direction of
(+) is change to "MIN", turn the direction of (–)
is change to "MAX".
5. To exit from this mode, press the [
RESET" and turn the power off.
] and [ ] simultaneously. When
N Z
] button to "COLD
?/1
17