LG LSE3092ST Service Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Ranges
  5. LSE3092ST
  6. Service manual

LG LSE3092ST Service Manual

30” freestanding electric range
Hide thumbs Also See for LSE3092ST:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , User Manual
Internal Use Only
Website http://us.lgservice.com
30" Freestanding Electric Range
SERVICE MANUAL
MODEL: LSE3092ST
CAUTION
BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
December, 2009
P/NO : MFL62114802
Printed in Korea

Advertisement

Table of Contents
loading

Related Manuals for LG LSE3092ST

Summary of Contents for LG LSE3092ST

  • Page 1 Internal Use Only Website http://us.lgservice.com 30” Freestanding Electric Range SERVICE MANUAL MODEL: LSE3092ST CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. December, 2009 P/NO : MFL62114802 Printed in Korea...

  • Page 2: Safety Precautions

    SAFETY PRECAUTIONS • Repairs of the appliance should be carried out by a licensed technician only. Incorrect repairs may result in dangerous situations. If you need repairs, contact an LG Service Center or your dealer. • If the power cord is defective, it must be replaced by a qualified service agent with a UL listed range cord.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS GENERAL- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1 ~ 1-5 •...
  • Page 4 COMPONENT TEST - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1 ~ 4-16 •...

  • Page 5: General

    GENERAL IMPOR ANT SAFETY INSTRUCTIONS IMPOR ANT SAFETY INSTRUCTIONS Read and follow all instructions before using your oven to prevent the risk of fire, electric shock, injury to person, or damage when using the range. This guide don’t cover all possible conditions that may occur. For further assistance contact your service agent or manufacturer.
  • Page 6 GENERAL IMPOR ANT SAFETY INSTRUCTIONS IMPOR ANT SAFETY INSTRUCTIONS • Be sure your appliance is properly installed and grounded by a WARNING qualified technician. • Do not repair or replace any part of the appliance unless • DO NOT touch heating elements or specifically recommended in the manual.

  • Page 7: Surface Cooking Units

    GENERAL IMPOR ANT SAFETY INSTRUCTIONS IMPOR ANT SAFETY INSTRUCTIONS • Do Not Leave Children Alone - Children should not be left alone or SELF-CLEAN OVENS unattended in area where appliance is in use. They should never be • Do Not Clean Door Gasket – The door gasket is essential for a allowed to sit or stand on any part of the appliance.

  • Page 8: Model & Serial Number Label And Tech Sheet Locations

    GENERAL MODEL & SERIAL NUMBER LABEL MODEL & SERIAL NUMBER LABEL AND TECH SHEET LOCA TIONS AND TECH SHEET LOCA TIONS The Model/Serial Number label and Tech Sheet locations are shown below. Model & Serial Number Location Tech Sheet Location (On Low Rear Cover)
  • Page 9 GENERAL SPECIFICA TIONS SPECIFICA TIONS Model Number LSE3092ST Category Convection Overall Width 30" Installation type Freestanding Color availability Control Oven Glass Touch Cooktop Knob Display Scroll VFD Electronic clock & timer Control lock capability Audible preheat signal Special function Option(6 categories) 1.

  • Page 10: Using Your Range

    USING YOUR RANGE GENERAL INFORMA TION GENERAL INFORMA TION Rating Label Convection Bake / Roast Mode Upper element, lower element, Rear element(some Model numbers are recorded on the rating label. model) and fan operate during convection bake. Rating label is located on the lower front left corner Convection bake should be used for cooking of the oven frame.
  • Page 11 USING YOUR RANGE CONTROL P ANEL FEA TURES CONTROL P ANEL FEA TURES Warm 200˚F 250˚F 450˚F 300˚F 400˚F 350˚F SURFACE COOKING AREA LOCATOR : Identify RIGHT REAR (SINGLE) CONTROL KNOB : Use to which element the knob controls. control Right Rear Element. ELEMENT ON/OFF INDICATOR LIGHT : Shows RIGHT FRONT (TRIPLE) CONTRON KNOB : Use whether the surface element is turned on/off or hot.

  • Page 12: To Turn On A Single Surface Unit (Left Rear, Right Rear)

    USING YOUR RANGE Use to turn on the surface elements. An infinite To turn on the Warming Zone : choice of heat settings is available from LOW to (Center Rear) HIGH. The knobs can be set on or between any of There is the Warming Zone element located settings in the back center of the glass surface.

  • Page 13: Setting The Clock

    USING YOUR RANGE To increase the oven temperature: 1. SETTING THE CLOCK 1. Touch and hold the WARM/PROOF pad for CLEAR Desired CLOCK START 3 seconds. /OFF Time 2. Touch the WARM/PROOF pad 1 time 2. START, CLEAR/OFF AND ON/OFF PAD 3.

  • Page 14: Bake, Timed Bake, Delayed Timed Bake

    USING YOUR RANGE 5) BEEPER VOLUME 11. HEALTIER ROAST 1. Touch and hold the WARM/PROOF pad for Desired HEATIHER ROAST: 3 seconds temperature : Once -> Beef 2. Touch the WARM/PROOF pad 4 time : Twice -> Pork 3. Touch “1” pad for loud level : 3 times ->...

  • Page 15: Lower Oven Drawer

    USING YOUR RANGE LOWER OVEN DRA LOWER OVEN DRA To Operate the Lower oven Drawer CAUTION The purpose of the Lower Oven is to bake foods • Always use Pot Holders or oven using the same cooking times and temperatures you mitts when removing food from the would in a standard oven.

  • Page 16: Component Access

    COMPONENT ACCESS This section instructs you on how to service each component inside the range. The components and their locations are shown below. COMPONENT LOCA TIONS COMPONENT LOCA TIONS Door Locking Motor Main PCB & Micro Switch Infinite Switch Surface Elements Variable Thermostat Door Latch Assembly Oven Sensor...

  • Page 17: Removing The Back Cover

    COMPONENT ACCESS REMOVING THE BACK COVER REMOVING THE BACK COVER WARNING • DISCONNECT power supply cord from the outlet before servicing. • Replace all panels and parts before operating. • RECONNECT all grounding devices. - Failure to do so can result in severe personal injury, death or electrical shock.
  • Page 18 COMPONENT ACCESS REMOVING THE OVEN RELA Y PCB, POWER PCB, REMOVING THE OVEN RELA Y PCB, POWER PCB, POWER RELA Y AND SURGE FIL POWER RELA Y AND SURGE FIL 4. To remove the Oven Relay PCB, remove the 4 WARNING screws and disconnect 13ea connectors.

  • Page 19: Removing The Controller

    COMPONENT ACCESS REMOVING THE CONTROLLER REMOVING THE CONTROLLER 6. To remove the controller WARNING a) Pull out the knob of Lower Oven and remove the 2 screws of Knob Housing • DISCONNECT power supply cord b) Remove the 2 screws on the controller from the outlet before servicing.

  • Page 20: Removing The Main Pcb And Key Pcb Assembly

    COMPONENT ACCESS REMOVING THE MAIN PCB AND KEY PCB ASSEMBL REMOVING THE MAIN PCB AND KEY PCB ASSEMBL b) Grip the Main PCB supporter and pull it out WARNING from the controller strongly with opening the inlet of controller using another hand. •...

  • Page 21: Removing The Knob And Infinite Switch

    COMPONENT ACCESS REMOVING KNOB AND INFINITE SWITCH REMOVING KNOB AND INFINITE SWITCH c) Remove the 2 screw of Knob Housing WARNING d) Remove the 2 screw on the controller • DISCONNECT power supply cord from the outlet before servicing. • Replace all panels and parts before operating.
  • Page 22 COMPONENT ACCESS REMOVING THE CERAMIC GLASS COOKT , THE REMOVING THE CERAMIC GLASS COOKT , THE SURF ACE ELEMENT AND THE HOT SURF ACE LAMP SURF ACE ELEMENT AND THE HOT SURF ACE LAMP c) Remove 2 connectors which connect controller WARNING harness with cooktop harness.
  • Page 23 COMPONENT ACCESS REMOVING THE CERAMIC GLASS COOKT , THE REMOVING THE CERAMIC GLASS COOKT , THE SURF ACE ELEMENT AND THE HOT SURF ACE LAMP SURF ACE ELEMENT AND THE HOT SURF ACE LAMP b) Remove the 4 screws on the top ceramic wool WARNING c) Remove the 2 screws on the both side brackets, and remove the side brackets...
  • Page 24 COMPONENT ACCESS e) Remove the door latch from the burner box 8. To remove the thermal disk, remove the 1 screw and remove the 2 wires. and unhook the actuating rod. Unhook Actuating The thermostat is located on the cavity cover . It opens at 356°F/180°C and closes when the oven temperature cools below 14°F/-10°C.

  • Page 25: Removing The Broil Element

    COMPONENT ACCESS REMOVING THE BROIL ELEMENT REMOVING THE BROIL ELEMENT b) Pull the element forward so that you can WARNING access the terminals and disconnect the wires. • DISCONNECT power supply cord Terminals from the outlet before servicing. • Replace all panels and parts before operating.

  • Page 26: Removing The Hidden Bake Element

    COMPONENT ACCESS REMOVING THE HIDDEN BAKE ELEMENT REMOVING THE HIDDEN BAKE ELEMENT 1. Unplug range or disconnect power. 7. Bend the insulation glass fiber up. 2. Pull the range out of its mounting location so that you can access the rear of the unit. 3.
  • Page 27 COMPONENT ACCESS REMOVING THE CONVECTION ELEMENT AN BLADE AND F AN MOT REMOVING THE CONVECTION ELEMENT AN BLADE AND F AN MOT 1. Disconnect power and remove oven racks. 7. To remove Fan blade, remove Nut by screwing clockwise. Fan blade can be replaced from inside 2.

  • Page 28: Removing The Oven Light & Socket Assembly

    COMPONENT ACCESS REMOVING THE OVEN LIGHT & SOCKET ASSEMBL REMOVING THE OVEN LIGHT & SOCKET ASSEMBL CAUTION WARNING • DISCONNECT power supply cord • Be careful not to scratch or chip the from the outlet before servicing. oven liner paint when you remove •...

  • Page 29: Removing The Latch Drive Assembly

    COMPONENT ACCESS REMOVING THE LA TCH DRIVE ASSEMBL REMOVING THE LA TCH DRIVE ASSEMBL DOOR LOCKING MECHANISM WARNING The door lock assembly is located at the back side • DISCONNECT power supply cord of range. from the outlet before servicing. The structural elements are as below.

  • Page 30: Removing The Oven Temperature Sensors

    COMPONENT ACCESS REMOVING THE OVEN TEMPERA TURE SENSORS REMOVING THE OVEN TEMPERA TURE SENSORS 5. To remove an oven temperature sensor, WARNING disconnect the connector from the main harness and remove the two mounting screws in oven • DISCONNECT power supply cord cavity.
  • Page 31 COMPONENT ACCESS REMOVING & REPLACING THE LIFT -OFF OVEN DOOR REMOVING & REPLACING THE LIFT -OFF OVEN DOOR To replace the door: CAUTION Step. 1 • Be careful when removing and Firmly grasp both lifting the door. sides of the door •...

  • Page 32: Removing A Side Panel

    COMPONENT ACCESS REMOVING A SIDE P ANEL REMOVING A SIDE P ANEL 8. Pull the back of the side panel out from the range WARNING approximately 10˚ • DISCONNECT power supply cord from the outlet before servicing. • Replace all panels and parts before operating.

  • Page 33: Removing The Lower Oven Element

    COMPONENT ACCESS REMOVING THE LOWER OVEN ELEMENT REMOVING THE LOWER OVEN ELEMENT To Remove Lower oven Broil Element : WARNING 1. Pull the range away from the wall. • DISCONNECT power supply cord 2. Remove the 3 screws from the upper bracket and 2 screws from the rear bracket from the outlet before servicing.

  • Page 34: Removing The Variable Thermostat

    SAFETY REMOVING THE V ARIABLE THERMOST REMOVING THE V ARIABLE THERMOST 5. Remove 2 screws of the sensor bracket WARNING • DISCONNECT power supply cord from the outlet before servicing. • Replace all panels and parts before operating. 6. Remove the sensor of variable thermostat from •...

  • Page 35: Removing The Oven Door Handle & Glass

    COMPONENT ACCESS REMOVING THE OVEN DOOR HANDLE & GLASS REMOVING THE OVEN DOOR HANDLE & GLASS 5. Lift the liner assembly off the front glass and set WARNING it aside. 6. To remove the door handle & trim (for stainless model) •...
  • Page 36 COMPONENT ACCESS 7. To remove a hinge hanger assembly: f) Lift the inner oven door glass and bracket a) Remove the 2 top liner screws assembly out of the door liner. (See step 3 on page 3-14) b) Place the door liner assembly on a padded work surface with the hinge hangers over the edge.

  • Page 37: Removing The Oven Door Gasket

    COMPONENT ACCESS REMOVING THE OVEN DOOR GASKET REMOVING THE OVEN DOOR GASKET 3. Pull the ends of the gasket out of the liner holes. WARNING Liner Hole • DISCONNECT power supply cord from the outlet before servicing. • Replace all panels and parts before operating.

  • Page 38: Component Test

    COMPONENT TEST Before testing any of components, perform the following checks: NOTE: 1. The most common cause for control failure is corrosion on connectors. Therefore, disconnecting and reconnecting wires will be necessary throughout test procedures 2. ALL units in the first few days of use should be checked for mis-wiring or loose connections 1.

  • Page 39: Door Locking Motor

    Components Test procedures Results Normal: Approximately Door locking Motor 1. Refer to page 3-14 for the servicing procedure 2.6 kΩ ± 10% 2. Measure the resistance If not replace (Multiple meter scale: R x 1000) Abnormal: Infinite(open) below 5Ω (shorted) Door latch Door latch Micro Switch...

  • Page 40: Oven Sensor

    Components Test procedures Results Normal: Approximately Oven Sensor 1. Refer to page 3-15 for the servicing procedure 1.09 kΩ ± 10% 2. Measure the resistance after cooling down If not replace (Multiple meter scale: R x 1000) NOTE: Ω Value was tested at room temperature (77F/25˚C) NOTE: Oven sensor is so sensitive to temperature...

  • Page 41: Bake Heater

    Components Test procedures Results Normal: Approximately Bake heater 1. Refer to page 3-11 for the servicing procedure 17 Ω ± 10% 2. Measure the resistance after cooling down If not replace (Multiple meter scale : R x 1) NOTE: Ω Value was tested at room temperature (77F/25˚C) Be careful the element is...

  • Page 42: Oven Lamp

    Components Test procedures Results Normal: Below 5 Ω. Oven lamp 1. Measure the resistance after cooling down If not replace (Multiple meter scale: R x1)
  • Page 43 Components Test procedures Results Infinite switch 1. Refer to page 3-6 for the servicing procedure. (Single units): 2. Set the Multiple meter scale to the R x 1000. LR switch 3. Disconnect all wires from infinite switch. RR switch 4. When turn on/turn off the knob, position measure the resistance between L1 to H1.
  • Page 44 Components Test procedures Results Infinite switch 1. Refer to page 3-6 for the servicing procedure. (Single units): 2. Set the Multiple meter scale to the R x 1000. CR Switch 3. Disconnect all wires from infinite switch. 4. When turn on/turn off the knob, position measure the resistance between P1 to 2.
  • Page 45 Components Test procedures Results Infinite switch 1. Refer to page 3-6 for the servicing procedure. (Double units): 2. Set the Multiple meter scale to the R x 1000. LF switch 3. Disconnect all wires from infinite switch. 4. Push in and turn left knob to check the single type. 5.
  • Page 46 Components Test procedures Results Infinite switch 7. When turn on/turn off the knob, position measure (Double units): the resistance between 4 to 4a. LF switch 8. After check the single type, check the dual type at the same procedure. Infinite Switch Knob Position Results P1 - 2...

  • Page 47: Infinite Switch(Triple Units):Rf Switch

    Components Test procedures Results Infinite switch 1. Refer to page 3-6 for the servicing procedure. (Triple units): 2. Set the Multiple meter scale to the R x 1000. RF switch 3. Disconnect all wires from infinite switch. 4. Push in and turn left knob to check the single type. 5.
  • Page 48 Components Test procedures Results Infinite switch 7. When turn on/turn off the knob, position measure (Triple units): the resistance between 4 to 4a. RF switch 4b J4 8. When turn on/turn off the knob, position measure the resistance between J4 to4b. 4b J4 9.

  • Page 49: Variable Thermostat:lower Oven Switch

    Components Test procedures Results Variable Thermostat : 1. Refer to page 3-19 for the servicing procedure. NOTE: Ω Value was tested Lower oven switch 2. Set the Multiple meter scale to the R x 1000. at room temperature (75F/24˚C) 3. Disconnect all wires from Variable Thermostat 4.
  • Page 50 Components Test procedures Results Single surface units: 1. Refer to page 3-7 for the servicing procedure Left Rear (LR) 2. Set the Multiple meter scale to the R x 1 3. Disconnect wires from cook-top elements Right Rear(RR) 4. Touch the ohmmeter test leads to the element Element terminal and 1A.

  • Page 51: Center Rear(Cr) Element:warming Zone(Plane Heater)

    Components Test procedures Results Center Rear(CR) 1. Refer to page 3-7 for the servicing procedure Element 2. Set the Multiple meter scale to the R x 1 : Warming Zone 3. Disconnect wires from cook-top elements (Plane Heater) 4. Touch the ohmmeter test leads to the element terminal E1 and E2.
  • Page 52 Components Test procedures Results Dual surface units: 1. Refer to page 3-7 for the servicing procedure Left Front(LF) 2. Set the Multiple meter scale to the R x1 Element 3. Disconnect wires from cook-top elements 4. Touch the ohmmeter test leads to the (E1 & 1A) and (E2 &...
  • Page 53 Components Test procedures Results Triple surface unit: 1. Refer to page 3-7 for the servicing procedure Right Front(RF) 2. Set the Multiple meter scale to the R x 1 Element 3. Disconnect wires from cook-top elements 4. Touch the ohmmeter test leads to the (E1 & 1A) and (E2 &...

  • Page 54: Composition Of Control

    COMPOSITION OF CONTROL Main PCB ( P/N :EBR52349505) Power PCB ( P/N : EBR57124701 ) Front Back Relay PCB ( P/N : EBR60938302) Back Back cover Controller assembly Key PCB ( P/N : EBR60939401)

  • Page 55: Main Pcb

    COMPOSITION OF CONTROL Main PCB Main PCB P/N :EBR52349505 Power PCB Power PCB P/N EBR57124701...

  • Page 56: Relay Pcb

    COMPOSITION OF CONTROL Relay PCB Relay PCB EBR60938302 Key PCB Key PCB P/N EBR52350001...

  • Page 57: Failure Mode Flow Chart

    FAILURE MODE FLOW CHART Power Off Power Failed(Dead), No display? Replace the Is the electric wiring normal? defective Measure the resistance Power harness cord and CN01’s connection Power On State Normal : continuity Normal Abnormal Abnormal: infinite Check the key beep. Code L1 to Pin1 of CN01(RD) Touch the “clear key”, Go to No 4...
  • Page 58 FAILURE MODE FLOW CHART Power Off Power Off Replace the Replace the Check the voltage of Is the voltage of Main PCB’s Power PCB Power PCB Vcc 4.5V ~ 5.5V? Check the Main PCB Is the voltage as below? voltage between pin2 and pin3 of IC2 PIN No.
  • Page 59 FAILURE MODE FLOW CHART Symptom Check Point 1. No heating 1.Check Electric Wiring 2. F11 2.Check Heater’s Resistance. 3.Check the Sensor. 3,400W Heater Resistance Sensor Resistance...

  • Page 60: Oven Does Not Heat, F-11

    FAILURE MODE FLOW CHART Power Off Oven does not heat, F-11 Replace the Is the heater normal? Failed heater Power Off Measure the resistance of each heater. (The resistance is shown Reconnect or Is the disconnect or loose below) repair the connector? connector 1.
  • Page 61 FAILURE MODE FLOW CHART Power Off Range Of the resistance Replace the Is the resistance of failed thermistor normal? Ω thermistor Heater Resistance[ Approximately Check: Broil 13.0 Pins 1and 2 of CN5 wiring in main PCB Normal- approximately 1.09_ at 25_ Bake 17.0 Convection...

  • Page 62: Door Lock System Failure,F-10

    FAILURE MODE FLOW CHART Symptom Check Point 1. Door Lock System 1.Check Electric Wiring Failure 2.Check Motor’s Resistance. 2. F-10 3.Check the Relay PCB(Lock Motor Relay) Door lock Relay...
  • Page 63 FAILURE MODE FLOW CHART Power Off Door Lock System Failure,F-10? Replace the Is the door lock switch (micro switch) normal? micro switch Note : measure the resistance of Just after self-clean start, the door lock motor door lock switch normally open type starts to rotate.

  • Page 64: Sensing Fail, F-1, F-2

    FAILURE MODE FLOW CHART Symptom Check Point 1. Sensing Fail 1.Check the Electric Wiring 2. F-1 2.Check the Test Mode 3. F-2 3.Check the Sensor’s Resistance...
  • Page 65 FAILURE MODE FLOW CHART Power On Sensing Fail, F-1, F-2? Is the value of thermistor Go to No 1 normal? Power Off Check: using the test mode To enter the testmode, follow these steps: 1. press the “clear” key Is the disconnect or loose Reconnect 2.

  • Page 66: Oven Too Hot, F-6, F-16

    FAILURE MODE FLOW CHART Symptom Check Point 1. Oven hot 1.Check the Resistance of the Relay. 2. F-6 Relay Short check 3,400W 6-10...
  • Page 67 FAILURE MODE FLOW CHART Oven too hot, F-6, F-16? TAB5 Power Off Replace the Is the resistance of failed thermistor normal? thermistor TAB3 Check: Pins 1and 2 of CN5 wiring in main PCB Ω Normal- approximately 1.09 at 25 Power Off Replace Is the DLB relay normal? the relay PCB...
  • Page 68 FAILURE MODE FLOW CHART Power On Replace IIs the value of thermistor the Main PCB normal? (EBR52349505) Check: using the test mode To enter the testmode, follow these steps: 1. press the “clear” key 2. press the “BAKE”,”BROIL” key at the same time 3.
  • Page 69 FAILURE MODE FLOW CHART Symptom Check Point 1. Keypad Failure 1.Check the Door Locking System. 2. F-3 Error 2. Check the Electric Wiring. 6-13...

  • Page 70: Error (Touch-Sensor Key Error) Or Key Does Not Input

    FAILURE MODE FLOW CHART Power On F-3 error (Touch-sensor key error) Or Key does not input Replace Is the Key PCB The Key PCB normal operation? (EBR60939401) Power Off Check: Re-connect CN1 of Key PCB Reconnect Is the disconnect or and CN3 of Main PCB or repair Using the key test mode...

  • Page 71: Appendix

    APPENDIX Key operation T Key operation T How to check Key operation 1. Keys should be accessed according to priority and check the buzzer operation when key is accessed 2. If change the key access order, the buzzer make another beep 3.

  • Page 72: Trouble Shooting

    TROUBLE SHOOTING BEFORE CALLING FOR SERVICE BEFORE CALLING FOR SERVICE Before you call for service, review this list.It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Problem Possible Causes / Solutions Range is not level.
  • Page 73 TROUBLE SHOOTING Problem Possible Causes / Solutions Oven will not work • Plug on range is not completely inserted in the electrical outlet. - Make sure electrical plug is plugged into a live, properly grounded outlet. • A fuse in your home may be blown or the circuit breaker tripped. - Replace the fuse or reset the circuit breaker.
  • Page 74 TROUBLE SHOOTING Problem Possible Causes / Solutions Food does not broil • Aluminum foil used on the the broiling pan and grid has not been fitted properly and properly slit as recommended. - See the Broil section in the User's Guide. •...

  • Page 75: Schematic Diagram

    SCHEMATIC DIAGRAM WARNING WIRE COLORS RADIANT COOK-TOP SYMBOL COLOR POWER MUST BE DISCONNECTED BEFORE Wattage Ω BLACK SERVICING THE APPLIANCE. FAILURE TO DO SO RR: 1200W approx. 48Ω CAN RESULT IN DEATH OR ELECTRICAL SHOCK. LR: 1200W approx. 48Ω WHITE LF: 3000W approx.

  • Page 76: Strip Circuits

    1.Check the line voltage, household fuse or circuit breaker. 2.Check for loose wiring or mis-wiring within electric range. NOTE: The following individual circuits are for use in diagnosis, and are shown in the ON position. For Model: LSE3092ST CONV. BAKE / CONV. ROAST TAB2...

  • Page 77: Oven Light

    For Model: LSE3092ST OVEN LIGHT LOWER OVEN DRAWER CR (Warming Zone) Power Relay Regulator for CR Warm Residual Heat Indicator Lamp Neon Indicator Lamp Lamp Pilot RR Cook-top Element Power Relay 1a 1b Residual Heat Regulator for RR 6" Indicator Lamp...
  • Page 78 For Model: LSE3092ST LR Cook-top Element Power Relay 2a 2b 1a 1b Regulator for LR 6" Residual Heat Indicator Lamp Neon LR Single Indicator Lamp 1,200W Lamp LF Cook-top Element Power Relay Regulator for LF 9" Residual Heat LF Inner...

  • Page 79: Exploded View

    #EV# EXPLODED VIEW INTRODUCTION MODEL: COOKTOP PARTS CONTROLLER PARTS DOOR PARTS CAVITY PARTS DRAWER PARTS -10-1-...

  • Page 80: Door Parts

    #EV# DOOR PARTS W149 W243 W225 1733 1000 1703 1018 W222 1020 1028 1734 W101 W109 W101 1703 1015 1733 1704 1009 W149 1734 W149 W172 1704 1381 W149 -10-2-...
  • Page 81 #EV# CONTROLLER PARTS 2006 2085 5072 2083 W105 3006 2010 2086 2026 2083 2082 2061 2410 2082 2440 2021 W280 2084 W280 2026 2388 2082 2501 2026 W144 3006 2026 2088 2021 W280 W231 2088 2082 W231 W231 2400 2440 2026 W280 2440...
  • Page 82 #EV# COOKTOP PARTS 3014 3056 3016 W231 3401 W172 W144 W144 3079 3006 W231 W232 3303 9000 3022 W232 3303 3098 W105 3058 W144 3402 3302 3301 W105 3058 W144 3402 3107 -10-4-...
  • Page 83 #EV# DRAWER PARTS 8388 W144 8513 8514 W149 8501 W228 8520 W109 W108 8507 8513 W144 W108 W144 W109 W144 8520 W144 8522 W144 8519 W149 8540 3006 8541 8539 8517 8506 8512 W105 W144 W144 8515 W144 W144 W144 8505 5505 W144...
  • Page 84 #EV# CAVITY PARTS 5532 W144 W144 3013 5124 W144 W144 W102 5006 5510 W144 3063 W109 5049 9001 W109 W144 3006 5501 5517 5016 W144 5701 5409 W144 5055 5700 5071 W146 W109 W146 5410 5611 3006 5070 5700 W293 W231 3006 W109...

Table of Contents