Bostitch RN45B Operation And Maintenance Manual
  1. Manuals
  2. Brands
  3. Bostitch Manuals
  4. Nail Gun
  5. RN45B
  6. Operation and maintenance manual

Bostitch RN45B Operation And Maintenance Manual

Coil-fed pneumatic roofing nailer
Hide thumbs Also See for RN45B:
Table of Contents

Advertisement

Quick Links

See also: Operation & Maintenance Manual
RN45B
COIL-FED PNEUMATIC ROOFING NAILER
CLAVADORA NEUMÁTICA ALIMENTADA POR ROLLO PARA TECHADO
CLOUEUR PNEUMATIQUE À ENROULEMENT POUR TOITURE
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN Y DE MANTENIMIENTO
MANUEL D'INSTRUCTIONS ET D'ENTRETIEN
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR STANLEY-BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE SEGURI-
DAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA
PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON SU REPRESEN-
TANTE DE STANLEY-BOSTITCH O CON SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D'UTILISER L'APPAREIL. PRÉTER UNE
ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX AVERTISSE-
MENTS. GARDER CE MANUEL AVEC L'OUTIL POUR FUTUR RÉFÉRENCE. SI VOUS AVEZ DES
QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE CONCESSIONNAIRE
STANLEY-BOSTITCH.
103280REVE 5/99
Stanley Fastening Systems

Advertisement

Table of Contents
loading

Related Manuals for Bostitch RN45B

Summary of Contents for Bostitch RN45B

  • Page 1 DAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON SU REPRESEN- TANTE DE STANLEY-BOSTITCH O CON SU DISTRIBUIDOR. LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX AVERTISSE- MENTS.

  • Page 2: Table Of Contents

    INTRODUCTION The Stanley-Bostitch RN45B is a precision-built tool, designed for high speed, high volume nailing. These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power tool, for best performance the manufacturer’s instructions must be followed.

  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

  • Page 4: Tool Specifications

    PRESSURE. AIR CONSUMPTION: The RN45B requires 3.9 cubic feet per minute of free air to operate at the rate of 100 nails per minute, at 80 p.s.i. (5.6 kg/cm ). Take the actual rate at which the tool will be run to determine the amount of air required.

  • Page 5: Air Supply: Fittings, Hoses, Filters, Air Consumption, Regulators, Operating Pressure, Setting Correct Pressure

    Frequent, but not excessive, lubrication is required for best performance. Oil added through the air line connection will lubricate the internal parts. Use STANLEY-BOSTITCH Air Tool Lubricant, Mobil Velocite #10, or equivalent. Do not use detergent oil or additives as these lubricants will cause accel- erated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool maintenance.

  • Page 6: Loading The Tool

    Place the first nail in front of the front tooth on the feed pawl, in the driver channel. The nail heads must be in the slot in the nose. NOTE: Use only nails recommended by Stanley-Bostitch for RN45B series nailers or nails which meet the Stanley-Bostitch specifications.

  • Page 7: Tool Operation

    THIS MANUAL. II. REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL. There are three available systems on STANLEY-BOSTITCH pneumatic tools. They are: 1. TRIGGER OPERATION 2. CONTACT TRIP OPERATION 3. SEQUENTIAL TRIP OPERATION OPERATION 1.

  • Page 8: Tool Operation Check

    IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANUAL OBSERVE THE FOLLOWING FOR SAFE OPERATION • Use the STANLEY-BOSTITCH pneumatic tool only for the purpose for which it was designed. • Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area.

  • Page 9: Basic Tool Operation (Diagram)

    BASIC TOOL OPERATION Stanley-Bostitch pneumatic tools are cycled by a compressed air operated single piston design. The following illustrations show the four functional cycles that occur when the tool is operated to drive a fastener: FIG.1 FIG.2 EXHAUST OPEN AT REST...

  • Page 10: Trouble Shooting

    COIL NAILERS Skipping fasteners; intermittent feed Feed piston dry ....Add STANLEY-BOSTITCH Air Tool Lubricant in hole in feed piston cover Feed piston O-rings cracked/worn ..Replace O-rings/check bumper and spring.

  • Page 11: Driver Maintenance/Directional Exhaust

    ACCESSORIES AVAILABLE BC601 4 oz. Stanley-Bostitch Air-Tool Lubricant BC602 1 pint Stanley-Bostitch Air-Tool Lubricant BC603 1 pint Stanley-Bostitch "Winter-Formula" Air-Tool Lubricant BC604 1 quart Stanley-Bostitch Air-Tool Lubricant 100679 O-Ring Lube 1 lb. can SEQ1 Sequential Trip Conversion Kit...

Table of Contents