General; Getting Started - Sony SLV-ED115 Service Manual

SLV-ED115/ED215/ED313/ED515/ED616/ED815/ED817/ED818/ED915/ED919/EZ111/
Step 2
Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by
matching the + and – on the batteries
to the diagram inside the battery
compartment.
Insert the negative (–) end first, then
push in and down until the positive
(+) end clicks into position.
Using the remote commander
You can use this remote
commander to operate this
VCR and a Sony TV. Buttons
on the remote commander
marked with a dot (•) can be
used to operate your Sony TV.
If the TV does not have the g
symbol near the remote sensor,
this remote commander will
not operate the TV.
TV/VIDEO
To operate Set
VIDEO
the VCR and point at the remote sensor on the VCR
a Sony TV TV and point at the remote sensor on the TV
Notes
• The TV/VIDEO button selects the TV's input source (either aerial in or line in). The
button does not control this VCR.
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
Additional connections
Note
• To play a tape in stereo, you must use either
one of the connections shown below.
To a TV that has audio/video input jacks
This additional connection improves
picture and sound quality. Connect the
TV as shown on the right.
To a stereo system
You can improve sound quality by
connecting a stereo system as shown on
the right.
Remote sensor
TV/VIDEO
to

Getting Started

LINE OUT
LINE IN
Audio/video cable (not supplied)
LINE AUDIO OUT
LINE IN
Audio cable (not supplied)
Getting Started
EZ212/EZ414/EZ715/EZ717
SECTION 1

GENERAL

Step 3
Connecting the VCR
Connect the aerial to your VCR and TV as shown below to watch TV
programmes and VCR pictures on your TV. In addition, if your TV has
audio/video (A/V) input jacks, we recommend you connect the VCR to
your TV using an audio/video cable to get a better picture and sound.
Connecting the aerial
to mains
1
2
3
5 6
Getting Started
Step 4
Tuning your TV to the VCR
If you have connected your VCR to the TV using the audio/video cable, skip
this step.
1
ON/STANDBY
2
RF CHANNEL
3
4
RF CHANNEL
PROGRAM
7 8
Getting Started
1-1
This section is extracted from
SLV-ED919MI Instruction Manual.
(3-065-580-11)
AERIAL IN
AERIAL OUT
Mains lead
AERIAL IN
: Signal flow
Aerial cable (supplied)
Disconnect the aerial cable from your TV
and connect it to AERIAL IN on the rear
panel of the VCR.
Connect AERIAL OUT of the VCR and
AERIAL
the aerial input of your TV using the
supplied aerial cable.
Connect the mains lead to the mains.
If the 3-pin plug does not fit into the mains outlet, detach the plug
by loosening the screw, then use the 2-pin plug inside.
?/1 ON/STANDBY
RF CHANNEL PROGRAM +/–
Press ?/1 ON/STANDBY to turn on the VCR.
Press RF CHANNEL on the VCR.
The factory-preset RF channel flashes in the display window for
about three seconds.
Press RF CHANNEL again while the RF channel is flashing.
The VCR signal is output through this channel to the TV.
SP
Turn on your TV and select a programme position for the VCR picture.
This channel will now be referred to as the video channel.
Some TVs reserve a programme position, such as "0", for a VCR. In
this case, select the reserved programme position for the VCR
picture. Refer to your TV's instruction manual for details.
Press RF CHANNEL.
The TV system indicator appears in the display window.
Press PROGRAM +/– to select the correct TV system.
If your TV colour system and TV system are
PAL I
D/K
B/G
NTSC M
SP
AERIAL
IN
OUT
IN
OUT
APC
Select
I
K
G
M
Selected TV system
APC