Table of Contents
Advertisement
CATEYE
STEALTH 10
CYCLOCOMPUTER CC-GL10
ENG
Instruction manual
Before using the computer, please thoroughly read this manual
and keep it for future reference.
*
This PDF contains a link to YouTube.
When you click on the button "Watch a video", a message regarding secu-
rity appears.
Click the "Allow" to open a browser and play the video.
*
This manual has been prepared on the assumption that the user has suffi-
cient basic knowledge, including operation and terminology of PCs (Win-
dows / Mac).
066601221 1
Features of this unit
Measurement method
This unit is a cyclocomputer, having a GPS and acceleration sensor built-in, which can per-
form measurement by receiving GPS signal, without speed sensor.
Recording and viewing the trip route
Position information from GPS is recorded with measurement data during measurement.
The measurement data such as your route and altitude can be viewed as a trip on a map on
the site, by loading them into the dedicated software application "CATEYE Sync™" on your
PC, and then uploading to the special website "CATEYE Atlas™".
"CATEYE Atlas™" can be used as a database for your cycling life, where you can store the
trips measured using this unit or CATEYE INOU, a trip recorder with camera.
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
L'appareil est conforme à la réglementation FCC, section 15 et Industrie Canada RSS standard
exempts de licence (s). Son utilisation est soumise à deux conditions :
1. L'appareil ne doit pas provoquer d'interférences nuisibles, et
2. L'appareil doit supporter les interférences reçues, y compris les interférences empêchant son
fonctionnement correct.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are
not expressly approved by CatEye Co., Ltd. may void the user 's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected. Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
1
Advertisement
Table of Contents
Related Manuals for Cateye Stealth 10 CC-GL10
Summary of Contents for Cateye Stealth 10 CC-GL10
- Page 1 PC, and then uploading to the special website “CATEYE Atlas™”. ”CATEYE Atlas™” can be used as a database for your cycling life, where you can store the trips measured using this unit or CATEYE INOU, a trip recorder with camera.
-
Page 2: Cautions When Measuring
Proper use of the CatEye STEALTH 10 Warning / Caution The measuring result may differ slightly from the actual value, since this unit calculates the speed from GPS signal. • Do not concentrate on the computer while riding. Ride safely! Battery •... -
Page 3: Description Of Computer And Its Parts
Description of computer and its parts Screen display Computer Icon Description Battery icon Displays the remaining battery capacity in 5 levels. Front Back For information on how to charge the battery, see Power button “How to turn on/off the power / how to charge the battery”... -
Page 4: How To Install The Unit On Your Bicycle
How to install the unit on your bicycle Cut the excess length of the band using scissors. Watch video Click the button, then a browser will open and a Caution: Round off the cut edge of the bracket strap to prevent (YouTube) injury. -
Page 5: Setting Up The Computer
Then, you can set up quickly using your PC, to the following instructions. by changing the computer configuration using the special software application “CATEYE Sync™”. For details, see “Changing the computer configuration” (page 20). -
Page 6: Select The Time Zone
Time zone list Select the time zone Time Time City code City name City code City name difference difference In reference to the following “Time zone list”, select the code London Darwin +9.5 for the city nearest from your current location. Paris Sydney Athens... - Page 7 Select the daylight saving time You can set the daylight saving time when you are on Daylight Saving Time. Select ON or OFF. Setting Description Displays 1 hour faster than regular clock. Displays in regular clock. Daylight saving time icon Register the setting ON ↔...
-
Page 8: How To Use The Computer
How to use the computer This unit is a sensor-less cyclocomputer using GPS. An environment where a GPS signal can be received is required for measurement. Three screens of GPS search screen, measurement screen, and standby screen are available in this unit, which are displayed alternatively according to the GPS receiving status and the bicycle operating status. -
Page 9: Functions Available On The Measurement Screen
Functions available on the measurement screen Starting/Stopping measurement Backlight When using it during night-time, the backlight always lights up. Caution: Press and hold the MODE button to reset the computer before and after Example: Setting of the night-time: 7:00 PM to 6:00 AM measurement. -
Page 10: Resetting The Measurement Data And Generating The Trip Data
The total distance ( Odo) cannot be reset. For information on how to upload to the CATEYE Atlas™, see “Uploading the measurement data (trip data)” (page 13). The unit has a limited memory capacity. When the data volume exceeds the memory capaci- ty, any new data can no longer be stored. -
Page 11: Setup Of Your Pc
Setup of your PC At first, access the special website CATEYE Atlas™ to register as a member. Then, install CATEYE Sync™ to your PC (Windows/Mac). You can upload the trip data measured with this unit to CATEYE Atlas™, STRAVA™, TrainingPeaks™ and others, or change the computer configuration using your PC. -
Page 12: Setting Cateye Sync
(page 20). Click on [Setting]. When using CATEYE INOU, click on [INOU] to start INOU Sync. When you use CATEYE INOU for the first time, download CATEYE Sync™ INOU from CATEYE Atlas™ to install it. The setting screen appears. -
Page 13: Uploading The Measurement Data (Trip Data)
The menu screen appears. Uploading the trip data to CATEYE Atlas™ Save the trip data in the computer to your PC, and upload any trip data to CATEYE Atlas™. The trip data without the resetting operation cannot be recognized with CATEYE Sync™. -
Page 14: Exporting The Trip Data
Uploading for the first time requires the authentication of each service site. Check the trip data you want to upload, and then click on [Upload]. Enter the authentication code issued by the service site to the CATEYE Sync authentication dialog, and then upload the data. - Page 15 Click on the file format for export. CATEYE Sync™ The measurement data loaded into e-Train Data™ can be used with CATEYE Atlas™ and other services (STRAVA™ etc.) by importing it to CATEYE Sync™. Export the measurement data from e-Train Data™, and prepare a file.
-
Page 16: Data Contained In The Trip Data
FULL” appears flashing on the screen, and no new data can be recorded. Transfer the trip data to CATEYE Sync™ to secure the stor- age volume of the computer. Only when exceeding the maximum time for one trip, the reset-... -
Page 17: Reviewing, Editing And Sharing The Trip (What You Can Do With Cateye Atlas™)
You can share the trip with your friends and other users, by editing the trip information uploaded to CATEYE Atlas™. Access CATEYE Atlas™. Access the website “CATEYE Atlas™” from your browser (http://www.cateyeatlas.com). Click on [Login here]. Ride data When you have not registered your membership, see “Mem- bership registration to CATEYE Atlas™”... -
Page 18: Deleting The Gps Point
Now, editing the trip information is completed. Click on [Delete trip] on the trip information editing screen. Click on [Delete]. The CATEYE Sync™ trip data on your PC is not affected. The deleted trip can be restored by re-uploading from CATEYE Sync™. - Page 19 Exporting to a GPX fil Export a general-purpose GPS data file from the trip. This can be used with other services, including Google Earth™. Click on [GPX export] on the trip information editing screen. A confirmation message appears. Click on [Export]. A GPX file is downloaded.
-
Page 20: Changing The Computer Configuration
You can change the computer configuration in two ways. Click on [Q Series / STEALTH]. • Changing the setting with CATEYE Sync™ (below on this page) The menu screen appears. You can change the configuration easily from your PC application, with the computer connected to your PC with the cradle. - Page 21 Click on [STEALTH] to change the settings. Setting items Description Tire circumference This is not used with this unit. Before changing the settings, click on [Read] to load the settings of the computer. You can enter the start value of the total distance, and add the trip distance to it.
-
Page 22: Changing The Settings Of The Computer Alone
Changing the settings of the computer alone From “Selecting the speed unit” (page 25) Pressing the MENU button with the measurement screen displayed changes to the menu Clock setting screen. Various settings can be changed on the menu screen. After you change the setting, be sure to press the MENU button to register it. -
Page 23: Changing The Time Zone (Shortcut)
Changing the time zone (shortcut) Time zone list Holding down the MODE button for 4 seconds with the menu top screen displayed returns Time Time City code City name City code City name the time zone to the previous one. Holding down it again returns to the original time zone. difference difference London... -
Page 24: Night-Time Setting
From “Clock setting” (page 24) From “Night-time setting” Night-time setting Setting the record interval Set the time when the backlight lights up. Set the second-scale interval to record the measurement data. When you do not want to turn on the backlight throughout the The maximum recording time / maximum time for one trip that day, set the start time and end time to the same hour. -
Page 25: When The Operation Is Unstable
When the operation is unstable From “Entering the total distance” (page 24) Selecting the speed unit When the computer displays incorrectly, perform the restarting operation to stabilize the operation. Select the speed unit (km/h or m/h). Performing the restarting operation deletes any records under measurement. Changing We recommend that you perform the resetting operation to generate the trip data, before the settings... -
Page 26: Troubleshooting
Troubleshooting The following troubles are not due to failure. See also “FAQ” in CATEYE Atlas™ (web) (http://www.cateyeatlas.com/qa/). Trouble Check Items Remedy Trouble Check Items Remedy The measurement data Measurement may stop, or the When the power is Remaining battery capacity is... -
Page 27: Maintenance
When the operating time decreases significantly, the battery life is close to an end. Elapsed Time 0:00’00” - 9:59’59” Please contact CatEye local distributor listed on our website www.cateye.com or CatEye for replacing battery. Trip Distance 0.00 - 999.99 km [mile]... -
Page 28: Limited Warranty
If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer. To return the product, pack it carefully and enclose the warranty certificate (proof of purchase) with instruction for repair.