Canceling A Cycle; Changing A Cycle Or Setting; Adding Items During A Cycle; Option Selections - KitchenAid KUDP01DL Use And Care Manual

Use this cycle for pre-
rinsed and lightly-soiled
loads. During the heated
dry, the heating element
cycles on and off.
Soil Rinse Main Rinse
Level Wash
Sensed
120°F
Heavy
(49°C)
120°F
Light
(49°C)
Use this rinse cycle for
rinsing dishes, glasses, and
silverware that will not be
washed right away.
Soil Pre- Main Rinse
Level Wash Wash
Sensed
A small amount of water is run through the pump to remove
†
soil particles between the main wash and final rinse.
NOTES:
The sensor in your dishwasher monitors the soil level. Cycle
time and/or water usage can vary from the numbers above as
the sensor adjusts the cycle for the best wash performance.
In the Normal cycle, the dishwasher pauses while soaking.
Soaking helps loosen soils on dishes for brilliant results.

Canceling a Cycle

Anytime during a cycle, press the Cancel pad.
The display shows
Your dishwasher starts a 2-minute drain (if needed). Let the
dishwasher drain completely. The light turns off after 2
minutes.
NOTE: If your dishwasher does not need draining, the light turns
off. Select a new cycle and options.
To stop the drain
You can press the Cancel pad again to stop the drain
immediately. Remember to drain the dishwasher before starting a
new cycle.
To clear the indicators
Press the Cancel pad before starting the dishwasher to clear all
options and cycles.
12
Use main
detergent
dispenser section.
Purge† Final Dry Time
Heated (min)
Rinse
79*
135°F
cycled
(57°C)
71*
135°F
cycled
(57°C)
Do not use
detergent with this
cycle.
Rinse Final Dry Time
Heated (min)
Rinse
10

Changing a Cycle or Setting

During the first minute of a cycle
1. Open the door.
2. Press a new cycle and/or options.
3. Check the detergent dispensers. They must be filled properly
Water
Usage
for the new cycle.
(gal/L)
4. Close the door. The dishwasher resumes the new cycle
7.1-8.6/
and/or option after a 5-second pause.
27-33
After the first minute of a cycle
5.5/21
1. Press the Cancel pad.
The display shows
Water
Usage
(gal/L)
1.8/7
Your dishwasher starts a 2-minute drain (if needed). Let
the dishwasher drain completely. The light turns off after 2
minutes.
NOTE: If your dishwasher does not need draining, the light
turns off.
2. Open the door.
3. Select a new cycle and/or options.
4. Check the detergent dispensers. They must be filled properly
for the new cycle.
5. Close the door.
6. Press the Start pad.

Adding Items During a Cycle

You can add an item anytime that the Add a Dish indicator glows.
Open the door and check the detergent dispenser. If the cover is
still closed, you can add items.
To add items
1. Lift up the door latch to stop the cycle. Wait for the spraying
action to stop before opening the door.
2. Open the door. Add the item.
3. Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5-second pause.
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
Press the Start pad to repeat the same cycle and options as the
previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press the Start pad, the dishwasher runs the last full wash
cycle and options.

Option Selections