Recording And Playback With Tape Deck - Pioneer SX-990 Installation, Operation And Service Manual

2.
3.
Set the SELECTOR switch
(S)to
the
pHONO
2lMtC
position.
Insert
the microphone plug to
MIC
jack
(16).
Speak into the
microphone. Adjust the
volume
and
tone
as desired. When the
microphone
is used
near
the
loudspeaker system,
do not
increase the volume
too
much,
or
howling
may occur.
When a microphone is
connected
to
Model
SX_ggO,
the turntable
connected
to
the PHONO
2 terminals
cannot
be
used. The equipment
operates for
monaural
reproduction
regardless
of
the
position
which the
MOD E
switch
(1 5)
is
set
to.
RECORDING
The
same signal
as
fiat
reproduced
from
loudspeakers
is always supplied to the
TAPE RECterminalsl22l
.
According
to
the
program source desired
to
be
recorded, operate
the
SELECTOR
swjtch (5)
and
MODE sruitch
(15),
referring
to
,,Reception
of
broadcast" and "Play of
disk
record,,. The
signal
does
not
corrcern
fre
VOLUME,
BASS or
TREBLE controls
of
Model SX-990,
Adjust
the
recording
lwel whh
the controls prwided on
the
tape deck
(or tape recorder).
NOTE;
lf
a
monaural tape recorder
is
used, either
channel signal only
can
be
reoded.
PLAYBACK
Turn
on the
TAPE MONITOR wvitch (14),
and
adjust
the VOLUME (11),
BASS
(7)
and TREBLE
(8) controls
for
desired volume and tone.
o
When the TAPE
MONTTOR switch (141 is
in
the
"ON"
position,
the position
to
which the
SELECT-
OR switch
(5)
is set
is unrelated
to
the equipment
operation.
O
MULTI-AMPLIFIER
SYSTEM
A
multi-amplifier
system can
be composed
by
using
a two- or threedivision
band-pass
filter
and one
or
two
stereo power amplifiers
besides Model
SX-g90.
a)
Remove the
plugs which
connect the
pRE_AMp
output terminals (28)
to the MAIN-AMP INPUT
terminals (291.
bl
Connecr the
pRE-AMP OUTPUT terminals
to
the
input
terminals
of
the dividing
band_pass
filter,
and
the MAIN-AMP INpUT
terminals to
the output
terminals of
band-pass filters.
cl
Connect
the input
of
the other
stereo pow-
er
amplifiers
to
the
output terminals
of
the
other
dividing
band-pass filters.
one
of
the
dividing
TAPE
MONITOR
When
usinE a
Shead
tape
deck (or
tape recorder) for
repording,
monitor
can
be conducted
as
follows:
o
Turn on the TAPE
MONITOR srvitch
(14)
and the
after-recording
signal
will
be
monitored.
3
Turn off
the switch, and
the
before-recording
signal
will
be monitored.
Fis.
t o
ERASE
HEAD
RECORO
HEAD PLAY
BACK
HEAD
TAPE
RECORDING TERMINAL
TAPE
IV]ONITOR TERMINAL
iTAPE
MON]
TAPE
MONITOR
swtTcH
LOUDSPEAKER
AS
FOLLOWS
INTEGRATE
STEREO
SYSTEM
By
connecting
one
or
more
of
plONEER,s
Model
distortion
can
be
composed.
Also,
a
pA
system
to
be
used
in a large place
can
be
formed
by
using several
power systems wlth MoDEL sx-990.
&D
STEREO
SYSTEM
A
3-D
stereo system can
be
produced by
connecting
to
the
CENTER CHANNEL OUTPUT terminal (30i
a power
amplifier equippd with
a
low-pass
filter (f
=
150
to
250
Hz).
CENTER.CHANNEL
LOUDSPEAKER
SYSTEM
By connecting a
power
amplifir
and
loudspeaker
to
thE
CENTER CHANNEL OUTPUT
brMirNI
(30)
and
placing the
loudspeaker
at the
center
between
the
left and right
channel
loudspeakers,
the
,,hole
effect''
of
stereo sound
can
be
prwented.
\roh
Fig. 17