Kenwood KDC-X399 Instruction Manual page 22

AUDIO SETTINGS
EQ PRO (for /
BASS ADJUST BASS CTR FRQ
BASS LEVEL
BASS Q FACTOR
BASS EXTEND
MID ADJUST MID CTR FRQ
MID LEVEL
MID Q FACTOR
TRE ADJUST TRE CTR FRQ
TRE LEVEL
PRESET EQ DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/ NATURAL/
USER: Selects a preset equalizer suitable to the music genre. (Select [USER]
to use the customized settings.)
[DRIVE EQ] is a preset equalizer that reduces noise outside the car or
running noise of the tyres.
BASS BOOST LEVEL1/ LEVEL2/ LEVEL3: Selects your preferred bass boost level. ;
OFF: Cancels.
LOUDNESS LEVEL1/ LEVEL2: Selects your preferred low and high frequencies boost to
produce a well-balanced sound at a low volume level. ; OFF: Cancels.
EXTRA EQ (For )
LEVEL1/ LEVEL2/ LEVEL3: Selects your preferred elevation level to
enhance the sound in [PRESET EQ]. ; OFF: Cancels.
20
/ )
60HZ/ 80HZ/ 100HZ/ 200HZ: Selects the center
frequency.
–8 to +8 (+6): Adjusts the level.
1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
ON: Turns on the extended bass. ; OFF: Cancels.
0.5KHZ/ 1.0KHZ/ 1.5KHZ/ 2.5KHZ: Selects the
center frequency.
–8 to +8 (+5): Adjusts the level.
0.75/ 1.00/ 1.25: Adjusts the quality factor.
10.0KHZ/ 12.5KHZ/ 15.0KHZ/ 17.5KHZ: Selects the
center frequency.
–8 to +8 (0): Adjusts the level.
SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.
LPF SUBWOOFER THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/
160 Hz are sent to the subwoofer.
SUB-W PHASE REVERSE (180°)/ NORMAL (0°): Selects the phase of the
subwoofer output to be in line with the speaker output for
optimum performance. (Selectable only if a setting other than
[THROUGH] is selected for [LPF SUBWOOFER].)
HPF (Except for
THROUGH: All signals are sent to the speakers. ; 100HZ/ 120HZ/
150HZ: Audio signals with frequencies higher than 100 Hz/
120 Hz/ 150 Hz are sent to the speakers.
FADER R15 to F15 (0): Adjusts the rear and front speaker output balance.
BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance.
VOLUME OFFSET For AUX: –8 to +8 (0) ; For other sources: –8 to 0: Presets the
volume adjustment level of each source. (Before adjustment,
select the source you want to adjust.)
SOUND RECNSTR ON: Creates realistic sound by compensating the high-frequency
(Sound reconstruction) components and restoring the rise-time of the waveform that are
lost in audio data compression. ; OFF: Cancels.
• For : [SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/
[SUB-W PHASE] is selectable only if [SWITCH PREOUT] is set to [SUBWOOFER].
( 4)
• [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].
)