Satellite Radio Operation - Jensen VM9313 Installation And Operation Manual

Mobile multimedia receiver
Hide thumbs Also See for VM9313:
Table of Contents

Advertisement

<[~S£S:>
VM9313
SATELLITE RADIO OPERATION
Listeners can subscribe
to
X~ Radio
on the
Web by
visiting www.xmradio.com. or by calling (800) 967-2346.
Customers should have their Radio 10 ready (see
"Displaying the Identification (10) Code'? Customers can
receive
a
limited number
of
free-to-air channels without
activation.
Accessing Satellite Radio Mode
Press the SRC button (6) on the front panel or remote control
(8) to switch to the SAT source.
1.
SAT channel name
2.
SAT channel number
3.
SAT band
4.
Time
5.
Song title
6.
Artist name
7.
Song category
8.
Signal Strength Indicator
9.
Current preset channels/on-screen preset buttons
10. CH -: Select the previous channel
11. CH
+:
Select the next channel
12. CAT
+:
Select next channel in current category only
13. CAT -: Select previous channel in current category only
14. Touch to enter channel directly using keypad on screen
15.
CG:
Access Channel/Category Guide mode
16.
BAND:
Change between SAT1, SAT2 and SAT3 bands
17.
~:
Touch to view the SETUP menu
18. Touch this area to view the SOURCE MENU and select
a new playback source
19. MEM: View screen used to enter current channel into
preset memory
Displaying the Identification (ID)
Code
Before you listen to satellite radio, you must subscribe to the
service using your radio's identification number. To display
the radio ID, press CH - or CH
+
buttons on the touch screen
repeatedly to tune to channel '000'. The screen displays the
radio ID where the channel name is usually displayed.
Selecting a Station
Press the
or
»1
buttons (17, 19) on remote control or the
CH - or CH
+
buttons on the touch screen to change to
another station.
Preset Mode
To enter preset mode, touch the
BAND
button on the screen,
or press the
BAND
button on the unit (3) or remote control
(30) to change between the following bands: SAT1, SAT2, or
SAT3 (indicated in the top left comer of the TFT screen).
Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6) for the current
band appear on the TFT screen.
Storing
a
Station
1.
Select a band (if needed), then select a station.
2.
Touch the on-screen MEM button (18) to open the
preset screen.
ICH###
I
~§J@J
P4§J~
[
Ex i
t
I
3.
Touch the preset number in which you would like to
store the current station (or press EXIT to cancel and
close the menu). The preset number and station
appears highlighted.
Recalling
a
Station
1.
Select a band (if needed).
15
2.
Touch an on-screen preset button to select the
corresponding stored station.
Direct Tuning
To enter a radio station directly, touch the 88888 button or
press the GOTO button (21) on the remote control to display
the direct entry menu.
ICH:
/255
I
UJ00Q
GJ00D
0000
01
Clear
10
Enter the desired radio station using the on-screen' number
pad. Press the enter button (arrow) to tune to the selected
station. To exit the screen without changing the station, touch
Exit.
To clear your entry and start over, touch
Clear.
Channel/Category Guide Mode
There are two search modes to help navigate through
channels and or categories. To access the Channel/Category
Guide mode press, the ZOOM button (23) on the remote
control or the
CG
button on the touch screen.
Channel Guide is the default search mode. To access
Category Guide, press the TITLE button (2) on the remote
control or touch CAT on the touch screen. To return to
Channel Guide, touch CH on the screen or press the
SUBTITLE button (9) on the remote control.
Channel Guide Mode
When Channel Guide mode is selected, the first six satellite
channels are displayed in the boxes in the bottom left of the
TFT screen and the on-screen menu changes to facilitate
search mode.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents