Whirlpool thin twin Installation Instructions Manual page 6

Now check to see that all of the
parts you removed from the
inStallatiOn pah bag in step 2 are
now Installed rn the washer/dryer,
If YOU still have an extra aart.
~6
back through the steps to see
what you skrpped
phllllps screwdriver
AItemate installations:
recessed or cIoset area
locations.
The following are mrnimum
installatron spacings and
openings (In inches] that you
should allow. For easier installatron
and service, consider additional
spacing.
L
;
Dryer
Check to make sure you have all
the 1001s you started with
33
Take a few mrnutes to
m read the Use and Core
Guide so you can get the best use
from Your new washer/dryer. Now start
the washer and allow it to complete
one cycle [such as the permanent
Remove tape from dryer door
Open door and remove the tape
that holds the lent screen rn place
Check to be sure lent screen is
In Its proper positron. Wipe out
drum Start dryer ond allow it to
complete a cycle to make sure
the dryer is working properly
35
Finally. save all
n kterature and keep
with the washer/dryer. Save all
shipping materrals for reshipping
/Congiatu.lations!\
I
You hove just finlshed installing
Your new whirlpool
I
Washer
4
f L!l
G ' JcSide View
closet Door
LL
J
-I
H
0
f
I
t
Front View
Minlmum Installation Soacina
When the washer/dryer is
Installed in other than the
recessed and closet type of
Installation shown, minlmum
dIr&~~~dlcated must
To prevent large amounts of
lint and moisture from
occumulatlng and to malntaln
drying efftciency, this appliance
must be exhausted outdoors.
Non-exhausted Installotlon -
only rear exhaust positlon
permItted. Exhaust Deflector Kit
LCK4500 musf be used.
AItemate methods
of securing ribbed
pIastic drain hose
A
Put the bent end '
n
of the ribbed P
plastic drain hose '
in the tuborstandpipe.
Figure 3
B
The dram hose
m
must be held
securely with the
Stmp
plastic strap provided
so it does not come
out of the tub
or stondpipe _
durrng use
C
W
n ::
and secure as shown in
Figures 3 Standpipe. 4 Tub,
5 In-wall
slandprpe
Pi-b
cc
Figure 5 ,./g
Strap*
D If the drain hose cannot
n
be strapped rn place, it
must be cut exactly to
length so the bent end IS held
tightly over the edge of the tub or
standpipe [see Figure 6.)
Hose must be cut
exactly to length
SO the bent end
Is held tightly
over the edge
of the tub
orslandplpe.
BE SURE THE HOSE IS NOT lWlSTED
CR KINKED AND IS SECURELY
IN PlACE
AItemate exhaust
methods.
A There are exhaust
n
ktts available that allow
vou to direct filtered
exhaust dir inside to conserve
energY during winter months. You
may use these devrces with
Whrrlpool dryers providing their
use does not violate natronol or
locot codes, and the device does
not restrrct exhaust air flow, If You
use one of these kits, be aware
that excessrve moisture rn the
home can cause manv oroblems
and that you may see an Increase
in the time required to dry a load.
Also. YOU must maintarn the kit
rnstallbtion properly to avoid
excessive lint build-up, which can
affect the dryer's performance.
B
For mobile home
'
rnstallation. the dryer
must have an outside
exhaust If you exhaust the dryer
through the floor and the area
under your mobile home is
enclosed. the exhaust system
must terminate outside the
enclosed area Extension beyond
the enclosure will prevent lint
and moisture build-up under the
mobile home. See Figure 7.
Mobile home lnstallotlon
PANEL E