Urnace Tart; Urnace Hut Own; Ockout Eset - Goodman GAS-FIRED WARM AIR FURNACE User's Information Manual

F F F F F O O O O O
U R N A U R N A U R N A U R N A U R N AC E C E C E C E C E P E R P E R P E R P E RA A A A A TION P E R TION TION TION TION
E
LECTRICAL COMPONENTS ARE
T ,
O AVOID PERSONAL INJURY
REMOVE ANY INTERNAL COMPARTMENT
QUALIFIED SERVICER AT ONCE
Keep both doors in place except for inspection and maintenance.
An interlock switch prevents furnace operation if the blower door
is not in place.
F F F F F S S S S S -U -U -U -U -U
URNACE URNACE URNACE URNACE URNACE TART TART TART TART TART P P P P P
1. Close the external manual gas shut-off valve.
2. Turn off the electrical power to the furnace.
3. Set the room thermostat to the lowest possible setting.
4. Remove the burner compartment door.
5. This furnace is equipped with an ignition device which auto-
matically lights the burner. Do not try to light the burner by
hand.
6. Move the furnace's gas valve ON/OFF switch to the OFF posi-
tion.
7. Wait five minutes to clear out any gas. Then smell for gas,
including near the floor as some types of gas are heavier than
air.
8. If you smell gas following the five minute waiting period in
step 7, immediately follow the instructions on the cover of
this manual. If you do not smell gas after five minutes, move
the furnace's gas valve ON/OFF switch to the ON position.
9. Replace the burner compartment door.
10. Open the external manual gas shut-off valve.
11. Turn on the electrical power to the furnace.
12. Adjust the thermostat to a setting above room temperature.
13. After the burners are lit, set the thermostat to desired tem-
perature.
Gas Valve On/Off
Selector Switch
Honeywell Model VR8215 (Single-Stage) Honeywell Model VR8215 (Single-Stage) Honeywell Model VR8215 (Single-Stage)
Honeywell Model VR8215 (Single-Stage) Honeywell Model VR8215 (Single-Stage)
WARNING
CONTAINED IN BOTH COMPARTMENTS
,
ELECTRICAL SHOCK OR DEATH DO
. C
COVERS ONTACT A
IF AN ABNORMAL CONDITION IS
.
NOT
Gas Valve On/Off
.
NOTICED
Selector Switch
Honeywell Model VR9205 (Two-Stage) Honeywell Model VR9205 (Two-Stage) Honeywell Model VR9205 (Two-Stage) Honeywell Model VR9205 (Two-Stage) Honeywell Model VR9205 (Two-Stage)
White-Rodgers Model 36G22 (Single-Stage) White-Rodgers Model 36G22 (Single-Stage) White-Rodgers Model 36G22 (Single-Stage) White-Rodgers Model 36G22 (Single-Stage) White-Rodgers Model 36G22 (Single-Stage)
INLET
White-Rodgers Model 36G54 (Two-Stage) White-Rodgers Model 36G54 (Two-Stage)
White-Rodgers Model 36G54 (Two-Stage) White-Rodgers Model 36G54 (Two-Stage) White-Rodgers Model 36G54 (Two-Stage)
F F F F F S S S S S
URNACE URNACE URNACE HUT HUT HUT
URNACE URNACE HUT HUT
To shut down your furnace, follow the steps listed below.
1. Set the thermostat to the lowest setting.
2. Integrated control closes gas valve extinguishing flame.
3. Induced draft blower is de-energized following a 15 second
delay. The circulator blower is de-energized following a 90,
120, 150, or 180 second delay period.
4. Remove the burner compartment door.
5. Move the furnace's gas valve ON/OFF switch to the OFF posi-
tion.
6. Close the external manual gas shut-off valve.
7. Replace the burner compartment door.
L L L L L R R R R R
OCKOUT OCKOUT OCKOUT OCKOUT OCKOUT ESET ESET ESET ESET ESET
Furnace lockout is characterized by a non-functioning furnace
(circulator blower may be running continuously) providing a di-
agnostic LED code. Lockout results when a furnace control de-
tects abnormal conditions. If the furnace is in "lockout", it may
be reset by any of the following methods:
1. One hour automatic reset. Control will automatically reset
itself and attempt to resume normal operations following a
one hour lockout period.
2. Power interruption. Interrupt 115 volt power to the furnace
for greater than 20 seconds.
6
On/Off Switch
D D D D D
OWN OWN OWN
OWN OWN
OUTLET