Quick Start Reference Guide; Preprogrammed Pads - Amana AMH20 Service Manual

Quick Refence Guide
High Speed Commercial
Combination Oven
So...how do I use it?

Preprogrammed Pads

T
o cook food using preprogrammed pads.
(Example of pad is shown here.)
1. Open oven door, place food in oven and close door.
2. Enter selected item number using digit pad.
3. Cooking cycle begins.
4. At end of cooking cycle, oven beeps and returns to ready
mode.
Manual Operation
To cook food using a specific entered time and power level.
1. Press PREHEAT ON/OFF to start the oven.
• Preheat temperature and PREHEAT NOT READY
displays with NOT flashing.
2. Oven reaches preheat temperature.
• Signal sounds and PREHEAT READY displays.
ITEM must be flashing in display. If not, open and close
3.
oven door.
4. Press TIME ENTRY to program amount of cooking time.
• Enter desired cooking time by using numeric keypad.
• The total microwave cooking time (all stages
combined) is 20 minutes.
5. Press and hold TEMP ENTRY to program the radiant
heater. HTr shows in the display. Radiant heater setting
automatically defaults to 9 (highest).
• Set radiant heater by pressing pads 0 through 9.
• Pad 1 is the lowest heater setting; pad 9 is the highest
heater setting. 0 turns off radiant heater.
6. Press and hold POWER LEVEL to program fan speed. FAn
shows in the display. Fan speed setting automatically
defaults to 9 (fastest).
• Set fan speed by pressing pads 1 through 9.
• Pad 1 is the slowest fan speed; pad 9 is the fastest
fan speed.
7. Press POWER LEVEL to program level of microwave
power. Power level automatically defaults to High
(100%).
• For a lower microwave power, press pads 1 (for 10%)
through 9 (for 90%). 0 turns off microwave power.
8. If stage cooking is desired, press STAGE.
• Enter cook time, radiant setting, fan setting, and
power level for each stage by repeating steps 4-8.
• To enter another cooking stage for that pad, press
STAGE pad again. Up to four different stages can be
programmed for a total of 20 minutes microwave
cooking time.
9. Place food in oven and press the START pad to begin
the cooking cycle.
B–2

Quick Start Reference Guide

Refer to Product Safety Manual for Safety Statements
Complete Owner's Manual available online
Oven Clearances
A—Allow at least 2" (5.1 cm)
of clearance around top,
back and sides of oven.
Proper air flow around
oven cools electrical
components. With
restricted air flow, oven
may not operate properly
and life of electrical parts
is reduced.
B—Install combination oven
so oven bottom is at
least 3 feet (92 cm)
above floor.
Programming Preheat Setting
This oven can be set to a preheat setting of either 450°F
(240°C) or the factory default preheat setting of 475°F
(250°C).
To program the preheat setting:
1. Press PROGRAM SAVE pad.
2. Press TEMP pad.
3. Enter desired temperature by using the numeric key
pads.
4. Preheat temperature is changed.
Programming Items
1. Oven must be ON.
• Press PREHEAT ON/OFF.
• ITEM must flash in display. If not, open and close
oven door.
2. Press PROGRAM SAVE.
3. Press pad to be programmed or reprogrammed.
4. Follow steps 4 through 8 of "Manual Operation".
9. Press the PROGRAM SAVE pad to save the
programming into the pad.
NOTE:
16023463
A
To discard changes, press STOP/RESET before
pressing PROGRAM SAVE.
A
A
B
©2006 Maytag Services