Advertisement
SECTION1
WATER SOFTENER
START UP
C. PROGRAM
THE TIMER
_SET
WATER
HARDNESS
NUMBER
• Press
the SELECT
button
once to display
25 (de-
fault)
and HARDNESS
setting
screen.
The
grains
per
gallon
Hardness:
(gpg)
hardness
of your
_
Grains
water
supply
is on your
water
analysis
report.
Be
sure to write
down
water
Av CHANGE
SELECT
test
results
on
page
A,
and on instruction
decal located
under
the salt cov-
er, for future
reference.
If your water
supply
contains
iron, compensate
for
it by adding
to the water
hardness
number.
For ex-
ample, assume your water is 20 gpg hard and contains
2
ppm iron. Add 5 to the hardness
number for each 1 ppm
of iron. In this example, you would use 30for your hard-
ness number.
20 gpg hardness
2 ppmironx
5 = 10
+10
(times)
30 HARDNESS
NUMBER
• Press the UP / DOWN
buttons
to set your
water
hardness
number
in the display.
The DOWN
button
moves
the display
to 1. The UP button
moves
the
display
to the highest
setting
(see maximum
setting
Note:
Each press
of the UP / DOWN
button
changes
the
hardness
setting
by 1.
_SET
RECHARGE
(REGENERATION)
TIME
• Press the SELECT button
to display
2:00 AM (de-
fault)
and RECHARGE
TIME setting
screen.
At the 2:00 AM recharge
RechargeTime:
time
setting,
the softener
_
AM
begins
regeneration
(see
pages
2-3 and 2-4) at 2:00
AM
and
lasts
appoxi-
Av CHANGE
SELECT
mately
2-1/2
hours.
This
is a good time in most
households
because
water
is
not being used
(see Automatic
Bypass,
page 2-6). If
a different
recharge
time setting
would
be better
for
your
household,
do the following.
• Press
the UP / DOWN
buttons
to set the desired
recharge
starting
hour.
Be sure to observe
the AM-
PM as you did when
setting
the present
time of day.
•
Press
the SELECT
button
once
again,
to com-
plete
initial
programming.
l!
5:39
PM[
Recharge
Tonight
[
]1 More
Water
Flow
Normal
Operating
Screen
has
several
useful
items
that
can
be viewed
at a
glance.
The black
bars on
the
left
column
display
the amount
of salt in the
[]
5:39
PM
I
Recharge
Tonight
I
]]More
Water
Flow
storage
tank.
The present
time is shown
in the up-
per right hand
corner.
Options
are shown
in the top
center
of the display.
If the unit is going
to recharge
tonight
or is in a recharge,
this is shown.
By press-
ing the Up/X
arrow
displays
the "More"
screen.
"More"
Screen
shows
the
PCater Used'ibday:
water
used
today,
average
daily use, average
pounds
of salt used
per
recharge
0 Gallons
Avg Daily Use:
0 Gallons
Avg Salt/Rchg:
0.0 Pounds
R_,charg,, Count
0
and recharge
count.
If the recharge
count
is reset to
zero, the average
pounds
of salt per recharge
is reset
also.
PROGRAM
MEMORY
If electrical
power
to the
softener
goes off, the time display
is blank
but the
face plate
timer
keeps
the correct
time for about
72
hours.
When
electrical
power
comes
on again,
you
have to reset the present
time only if the Set Present
Time display
is showing.
The HARDNESS
and RE-
CHARGE
TIME
never
require
resetting
unless
a
change
is desired.
Even if the timer is incorrect
after
a long power
outage,
the softener
works
as it should
to keep
your
water
soft.
However,
regenerations
may occur
at the wrong
time of day until you reset
the timer
to the correct
time of day.
IF YOU NEED
HELP
PROGRAMMING
THE TIMER,
CALL TOLL FREE,
NUM BER 1- 800- 426- 9345.
SEE SECTION
2 FOR OTHER
FACE PLATE
TIMER
FEATURES.
1-4
Problems,
Questions?
Call
1- 800- 426- 9345
Kenmore
Water
Line
Advertisement
