Warranty - Empyre Pro Series 200 Intallation And Operation Instructions

Empyre Pro Series
Empyre Pro Series
10 Year Limited Warranty
Warranty service may only be performed by Pro-Fab Industries
or a Pro-Fab Authorized Empyre Pro Series Furnace Dealer
or a Pro-Fab Authorized Empyre Pro Series Furnace Service
Centre.
PRO-FAB INDUSTRIES INC. WARRANTY
Pro-Fab Industries Inc. (hereinafter called "Pro-Fab") warrants
to the original owner of the Empyre Pro Series Furnace
(hereinafter called the "Empyre Pro Series") the following:
A two (2) year warranty on the workmanship of the furnace and
workmanship on all parts manufactured by Pro-Fab, including
Pro-Fab manufactured owner-serviceable parts (provided
such parts are serviced in accordance with the Installation and
Operation Instruction Manual), from the manufacture date, and
excluding normal wear items such as (but not limited to) the
door gasket, fire brick, insulation, refractory, exterior finish and
chimney.
A one (1) year warranty for any labour required for any repair or
replacement of the furnace or parts from the date of manufacture
based on Pro-Fab's predetermined labour rates and allowable
hours.
A limited pro-rated warranty coverage (which includes the one
(1) year labour coverage at Pro-Fab rates and hours as stated
above) for a defective firebox and water jacket only, based on
the following pro-rated scale from the date of manufacture:
• Years one (1) and two (2) – one hundred percent (100%)
coverage;
• Years three (3), four (4) and five (5) – sixty percent (60%)
coverage;
• Years six (6) and seven (7) – thirty percent (30%)
coverage;
Pro-Fab will not be responsible or liable for any of the following: a) If
warranty work requires removal or replacement of all or a part of the
furnace, Pro-Fab is not responsible for the cost of plumbing, freight,
permits, removal or disposal of damaged furnace or parts, replacement
of water or additives, labour after the one (1) year warranty coverage
expires, or any cost other than the warrantied replacement part itself
or the furnace; b) The care, maintenance and safe operation of the
Empyre Pro Series Furnace which is the responsibility of the owner of
the furnace; c) Any accidents, injury, damage or loss incurred due to
a heating system failure; d) Any accidents, injury, damage or loss in-
curred due to faulty installation, operation or maintenance; e) Any cost
incurred for replacing or repairing of parts not manufactured by Pro-
Fab which carry their own manufacturer's warranty (except for the one
(1) year labour coverage at Pro-Fab rates and hours as stated above);
f) Any out-of-pocket expenses, alternative accommodations or loss of
revenue due to defective parts or furnace; g) Performance problems
caused by improper sizing of the furnace, vent connection, or air open-
There are no other warranties, expressed or implied, by Pro-Fab or its
Authorized Empyre Pro Series Furnace Dealers or Authorized Empyre
Pro Series Furnace Service Centres regarding the Empyre Pro Series
Furnace except the warranty expressed herein. ANY IMPLIED WAR-
RANTIES, INCLUDING MERCHANTABILITY, OR FITNESS FOR A PAR-
TICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE APPLICABLE
WARRANTY PERIODS SPECIFIED ABOVE. PRO-FAB'S SOLE LIABIL-
ITY, WITH RESPECT TO ANY DEFECT, SHALL BE AS SET FORTH IN
THIS LIMITED WARRANTY, AND ANY CLAIMS FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARE EXCLUDED.
Issue Date: September 2009
Models 100, 200 and 400
Part No. 815570
• Years eight (8) and nine (9) – fifteen percent (15%)
coverage;
• Year ten (10) – ten percent (10%) coverage.
Absolutely no warranty is provided after ten (10) years from the
date of manufacture.
Note: All parts NOT manufactured by Pro-Fab carry their
own manufacturer's warranty. The owner is responsible for all
costs necessary to replace those parts unless covered by the
applicable manufacturer (except for the one (1) year labour
coverage at Pro-Fab rates and hours as stated above).
The above warranties are based on the following factors:
Pro-Fab reserves the right to repair or replace at its discretion
any defective part or furnace, in whole or in part.
Use of Pro-Fab approved water treatment. IMPORTANT: Pro-
Fab approved water treatment is available from your local
dealer or service centre and must be used and validated for
warranty coverage. The pH balance must remain between
9.1 and 10.7, the nitrite level must remain between 730 and
1460 ppm as NaNO2, and conductivity must be less than or
equal to 4000 mmhos. A copy of the invoice itemizing the
purchase of approved water treatment will be required as proof
of maintenance in the event of a warranty claim. All laboratory
reports must be kept as proof of maintenance (see page 22 of
your Installation and Operation Instruction Manual).
All instructions in the Empyre Pro Series Installation and
Operation Instruction Manual must be followed.
The Warranty Registration and a copy of the original bill (invoice)
must be forwarded to Pro-Fab within thirty (30) days of the date
of purchase to validate the warranty.
ings; h) Damages, malfunctions or failures resulting from the use of
any attachment not authorized by Pro-Fab; i) Units installed outside the
continental United States, Alaska, or the provinces of Canada without
prior approval from Pro-Fab; j) Units with their safety certification labels
removed; or k) Damages, malfunctions or failures caused by force ma-
jeure, abuse, accident, fire, or acts of God.
Any available warranty will be void if: a) Annual maintenance proce-
dures are not followed (see Installation and Operation Instruction Man-
ual page 22); b) Water treatment and proper additives are not used as
specified in the Installation and Operation Instruction Manual (see page
22); c) The Empyre Pro Series Furnace has been altered in any way; d)
Any material other than Pro-Fab approved fuel has been used; e) Any
instruction given in the Installation and Operation Instruction Manual
which has not been followed including during installation or regular
maintenance; or f) Any claim made under the warranty for a person
other than the original owner.
No person is authorized to bind Pro-Fab to any other warranty what-
soever.
Pro-Fab reserves the right at any time to make changes or improve-
ments to the design, materials, or specifications of the Empyre Pro Se-
ries line of furnaces or parts without thereby becoming liable to make
similar changes in the furnaces or any of its parts previously manufac-
tured.
Manufactured by:
Pro-Fab Industries Inc.
Printed in Canada JW0909