Features - Mackie ONYX 1640i Quick Start Manual

Features

REAR PANEL / CONNECTION SECTION
1. AC POWER CONNECTION
2. POWER SWITCH
3. MIC INPUTS
4. LINE INPUTS
5. CHANNEL INSERTS
6. MAIN MIX XLR OUTPUTS
7. MAIN OUTPUT LEVEL (+4 dB/MIC)
8. MAIN MIX 1/4" OUTPUTS
9. MONO OUTPUT
10. MONO OUTPUT LEVEL
11. MAIN INSERTS
12. FIREWIRE CONNECTIONS
13. TAPE INPUTS
14. TAPE OUTPUTS
15. CONTROL-ROOM OUTPUTS
16. SUB OUTPUTS
17. AUX RETURN 1-4
18. AUX SEND 1-6
19. RECORDING OUTPUTS
20. HI-Z INPUTS
21. EXTERNAL TALKBACK INPUT
CHANNEL CONTROLS
22. 48V PHANTOM POWER (MIC ONLY)
23. LOW CUT SWITCH
24. CH. 1-16 INPUT (LINE OR FW 1-16)
25. HI-Z SWITCH (CH. 1 AND 2 ONLY)
26. GAIN CONTROL
27. SEND FIREWIRE PRE/POST EQ
28. HIGH EQ LEVEL
29. HIGH MID EQ FREQUENCY
30. HIGH MID EQ LEVEL
31. LOW MID EQ FREQUENCY
32. LOW MID EQ LEVEL
33. LOW EQ LEVEL
34. EQ IN/OUT SWITCH
35. AUX SEND 1-6 LEVEL
36. PAN
37. MUTE SWITCH
38. CHANNEL FADER
39. –20, 0, +10, AND OL LEDS
40. ASSIGN SWITCHES
41. SOLO SWITCH
4 Onyx 1640i
MASTER SECTION
42. HEADPHONE OUTPUT
43. BNC LAMP (12V, 0.5A)
44. CONTROL ROOM SOURCE: MAIN MIX
45. CTRL ROOM SOURCE: TAPE, SUBS 1-4, FW 1-2
46. ASSIGN CONTROL ROOM SOURCE TO MAIN MIX
47. CONTROL ROOM LEVEL
48. PHONES LEVEL
49. LEFT/RIGHT LEVEL METERS
50. RUDE SOLO LIGHT
51. SOLO LEVEL
52. SOLO MODE SWITCH: PFL/AFL
53. TAPE IN LEVEL
54. TAPE TO MAIN MIX SWITCH
55. AUX MASTER SEND 1-6 LEVELS
56. AUX SEND 1-6 PRE/POST SWITCHES
57. AUX SENDS SOLO SWITCHES
58. AUX SEND 1-6 TO FW 9-14 SWITCH
59. AUX MASTER RETURN 1-4 LEVELS
60. EFX TO MONITORS LEVELS
61. AUX RETURN 3 TO MAIN/SUBS SWITCH
62. SUBS 1-2/3-4 SWITCH
63. AUX RETURN 4 TO CR/PHONES ONLY SWITCH
64. POWER LED
65. TALKBACK MICROPHONE
66. TALKBACK LEVEL
67. TALKBACK DESTINATION: PHONES, AUX 1-6
68. TALKBACK ON SWITCH
69. EXTERNAL MIC SWITCH
70. SUB ASSIGN SWITCHES
71. SUB 1-4 FADERS
72. SUBS 1-4 TO FW 5-8 SWITCH
73. MAIN MIX FADER
74. ASSIGN MAIN MIX TO FW 15-16 SWITCH
AC POWER NOTES
1. AC POWER CONNECTION
This is a standard 3-prong IEC power connector.
Connect the supplied detachable linecord to the power
receptacle, and plug the other end of the linecord into
an AC outlet. The mixer can accept any AC voltage rang-
ing from 100 VAC to 240 VAC.
2. POWER SWITCH
Press the top of this rocker switch inwards to turn on
the mixer. The front panel power LED will glow with
happiness and the mixer will become fully operational.