Set Up Recording/Events [Rec & Event] - Panasonic WJ-NV200VK Installation Manual

Set up recording/events [REC & event]
The "REC & event" page has 3 tabs; the [Recording setup] tab, the [Event setup] tab and the [Advanced setup] tab.
Recording setup tab [Recording setup]
Configure the settings relating to schedule recording. Set the day(s), time table(s), frame rate and image quality for recording.
■ Schedules
Recording will be performed according to the schedules set
in advance. Select the day(s) of the week and the time
table(s).
[Days to record]
Select the day(s) of the week to record. Mark the
checkbox(es) of the day(s) of the week to record.
[Schedule to record]
3 time tables for schedule recording can be set up for "[Time
table 1]". The time bar indicates 24 hours in steps of 15 min-
utes.
Click the desired position on the time bar to designate the
start and end time. When the time is designated, the time
bar turns red.
Note:
• At the default, schedule recording has been set for
24 hours on Time table 1. To delete the designated start
and end time, right-click the timetable.
• The recording time table can be set by dragging the start
and end time on the time bar with the mouse.
• Be sure to set so that there is no overlap between the 3
time tables. When attempting to set the same time as
already set on another time bar, the time immediately
before or after the overlapping time will be set.
[HDD saving mode]
Reduce the frame rate to use less storage space on the
HDD. Mark the checkbox of this item to save HDD storage
space. Using H.264/MPEG-4 as compression method in this
mode will record only refresh interval images; using MJPEG
will record at a frame rate of 1 ips. This mode can be set
separately for each time table.
[Advanced >] button
The "Advanced schedule setup" page will be displayed. In
addition to 3 schedule recordings, 3 event recordings can be
set up. (☞ Page 53)
52
■ Recording setup (All cameras)
Set the recording frame rate and image quality. The settings
will be applied to all cameras.
[Frame rate]
Select the recording frame rate.
1 ips/ 3 ips/ 5 ips/ 10 ips/ 15 ips/ 30 ips
Default: 10 ips
Important:
• When selecting "MPEG-4" as compression method, the
setting value will provide an indication.
• When the compression method of the camera is
MJPEG, 10 ips, 15 ips and 30 ips are unavailable. The
default is "5 ips".
[Image quality]
Select the recording image quality.
NQ (Normal): Standard quality
FQ (Fine): High quality
SF (Super Fine): Super fine quality
XF (Extra Fine): Extra fine quality
Default: FQ
Note:
• If "XF" is selected when the compression method of the
camera is not "H.264", "SF" will be set instead of "XF".
[Referenced recording days]
Calculates and displays the total number of days for which
recording on the hard disk drives is available.
Note:
• The referenced recording days will be calculated based
on the assumption that recording is started on Monday.
• When the HDD saving mode is set, the actual recording
days are longer than the referenced recording days.
• The HDD consumption for the event recording will be
excluded.
• If a camera manufactured by other than Panasonic is
used, the value of "Referenced recording days" will not
be displayed.
• "*" preceding an item indicates that the item has been
changed on the "Advanced recording setup" page.
• If two or more cameras with the image capture size of
"FHD(1920x1080)", the image quality of "XF" and the
frame rate of "10 ips" or more are connected, images
may not be recorded at the configured rate.
[Advanced >] button
The "Advanced recording setup" will be displayed. Each
camera can be set up separately for recording. (☞ Page 54)