Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
Specification Front Panel Function Control Description Circuit Description Adjustment Procedure Troubleshooting Flow Chart Recommended Spare Parts List Exploded Diagram and Exploded Parts List Block Diagram 10. Schematic Diagrams 11. PCB Layout Diagrams ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
1. Precautions and Safety Notices (VE710s-4/VE710b-4) 1.1. SAFETY PRECAUTIONS This monitor is manufactured and tested on a ground principle that a user's safety comes first. However, improper use or installation may cause damage to the monitor as well as to the user. Carefully go over the following WARNINGS before installing and keep this guide handy.
12.SDA 8.GND 13.H.SYNC 4.NC 9. +5V 14.V.SYNC 5.GND 10.GND 15.SCL SIGNAL LEVEL CONNECTOR SIGNAL DESCRIPTION 0.7vp-p(VIDEO) GREEN 0.7vp-p(VIDEO) BLUE 0.7vp-p(VIDEO) H/SYNC TTL positive or negative V/SYNC TTL positive or negative DDC1/2B DDC1/2B ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
3. Front Panel Function Control Description VE710s-4/VE710b-4 Main Menu With OnView controls Front Control Panel shown below in detail Displays the control screen for the highlighted control. Scrolls through menu options and adjusts the displayed control. Also toggles between two...
Page 8
• If necessary, make small adjustments using H. POSITION and V. POSITION until the screen image is completely visible . (The black border around the edge of the screen should barely touch the illuminated “active area” of the LCD dislay.) ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
— Adds red to the screen image for warmer white and 6500K richer red. Default setting. — Adds green to the screen image for a darker color. 5400K ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 10
Vertical moves the screen image up and down. (Horizontal Size) adjusts the width of the screen image. H. Size Vertical size is automatic with your LCD dislay. NOTE: ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 11
OSD Timeout screen is displayed. For example, with a “15 second” setting, if a control is not pushed within 15 seconds, the display screen disappears. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 12
OSD control screens you can also view open software applications, or the Windows desktop. returns adjustments to the original factory Memory Recall settings if the display is operating in a factory Preset Timing Mode listed in this user guide. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 14
4. Circuit Description (VE710s-4/VE710b-4 M-star Scaler) A. Scaling controller The ADC is to convert RGB analog signal to digital signal that scaling chip can acknowledge. The HSYNC input receives a logic signal and provides the frequency reference for pixel clock generation.
Page 15
A “open drain pin” means it can sink at least 4mA current but only drive 10~20uA to VDD. It can be used as input or output function and needs ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 16
There are two signal to control the inverter which come from system. Logic “high” level which send to I901 is turn on the inverter. BRI signal control brightness by DC level which was integral from PWM signal. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Circuit Description (VE710s-4/VE710b-4 Realtek Scaler) A. Scaling controller General Embedded dual DDC support DDC1, DDC2B,DDC/CI Zoom scaling up and down Embedded Pattern Generator No external memory required. Require only one crystal to generate all timing Embedded reset control output Embedded crystal output to MICROP 3 channels 8 bits PWM output, and selectable PWM clock frequency.
Page 19
TCON [8] / V [3] V [3] AGRN [1] TCON [8] (1), (7), (8) V [3] TCON [7] / V [4] V [4] AGRN [0] TCON [7] (1), (7), (8) V [4] ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 20
(8), PWM1 / TCON [7] PWM1 / TCON [7] (1), (2), (3), (5), (8), PWM0 / REFCLK PWM0 / (In / out) test pin for DCLK / (2), (9) Video8 even-odd signal ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 21
There are two signal to control the inverter which come from system. Logic “high” level which send to I901 is turn on the inverter. BRI signal control brightness by DC level which was integral from PWM signal. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
5. Adjusting Procedure (VE710s-4/VE710b-4) 5.1. ADJUSTMENT CONDITIONS AND PRECAUTIONS 1. Approximately 30 minutes should be allowed for warm up before proceeding. 2. Adjustments should be undertaken only on those necessary elements since most of them have been carefully preset at the factory.
Page 23
(b). Change to each mode in turn and wait for the monitor finish auto-alignment and save process before change to next mode. (c). Until all of modes are agjusted, exit OSD menu and press PWR OFF to exit factory mode. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Firmware update procedure : (VE710s-4/VE710b-4) When you received a received monitor , please check whether the firmware version. If not , please followning procedures to upgrade to the latest version . 1. Equipment needed : ˘ VA721/VE710s-4/VE710b-4 ˘ PC ( Personal computer ) ˘...
Page 25
Hardware: PC or notebook, parallel(printer) cable, ISP tooling. Software: If OS was win2000 or WinXP , please install "PORT95NT.exe" In order to ensure can execute ISP program, please set BIOS in PC or Notebook as Fig 0.0 Fig 0.0 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 26
2. Double-click the " PORT95NT.exe" in Windows & initall the program. , see Fig 0.1 Fig 0.1 3. Keep on press " Next " 4 times to go through the installation processes, see Fig. 0.2 Fig. 0.2 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 27
4. Choose " Typical " then press " Next " , see Fig. 0.3 Fig. 0.3 5. Keep on press " Next " 4 times to go through the installation processes, see Fig. 0.4 Fig. 0.4 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 28
1. User could download ISP driver and PORT95NT install from Myson Century website (www.myson.com.tw ) 2. After extracting the ZIP file , the total files list as Fig 1.0 , and double click the file of setup.exe to install. Fig 1.0 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 29
4. Keep default setting or press " Change " button for selecting the path that you want , and then press " Next " button to continue , see Fig 1.2 Fig 1.2 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 30
5. Press " Install " button to continue , see Fig 1.3 Fig. 1.3 6. Installation has finished , press " Finish " button , see Fig 1.4 Fig. 1.4 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 31
3. The warning is used to remind user of that different CPU rate may cause ISP function fail. (it's limited by IIC protocol ) , Press " OK " button , see Fig 2.3 Fig. 2.3 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 32
4. Press " Create Security file " button to key in Security code . Adjusting bar to decrease speed of IIC bus , See Fig.2.4 . Speed of IIC bus Security code Fig. 2.4 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 33
7C , 4C , 77. The command No. and command must be set by user while coding. About the detailed of setting , please refer to section 6 boot code of ISP . Fig. 2.5 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 34
Select MTV type first , load the binary or intel hex file that you want to program into the MCU , and select " AUTO" item , then press " RUN " button , see fig3.1 Step 2 Step 1 Step 3 Step 4 Fig. 3.1 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 35
3. CRC ( cyclic redundancy check ) : the host can check CRC register's result instead of reading every byte in flash . The message of Check MCU CRC OK means that the host verify OK for the progress of program , see Fig.3.2 Fig. 3.2 ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 36
Procedure of Disassembly (VE710s-4/VE710b-4/VA721) This section provides disassembly procedures for VE710s-4/VE710b-4/VA721 LCD Monitor. Before you begin any of these procedures, be sure to turn off the power, computer system, and other attached devices; then disconnect the power cable from the electronically outlet. Moreover, when you disassemble the monitor, be sure to put the screws in a safe place and separate them according to grouping.
Page 37
Stand unit 3. Detach Stand unit from the monitor. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 38
2083740082 Detach Front Cover from the monitor. Unscrew two screws that secure Hinge Metal Fitting. Unscrew two screws that secure Keypad Board. Rear Cover Detach Rear Cover from the LCD Panel module. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 39
Unscrew one screw that secure Inverter top Shielding Plate and detach Inverter top Shielding Plate. Unscrew one screw that secure Inverter down Shielding Plate and detach Inverter down Shielding Plate. Disconnect three connectors to remove Inverter connector and LCD Panel FFC cable. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 40
LCD Panel 2080002200 Unscrew four screws that secure Metal Fitting and remove LCD Panel from Metal Fitting. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 41
1. Unscrew four screws that secure Main Board and disconnect the wires which are connected to Main Board and remove Main Board. " 2081430062 2. Unscrew four screws that secure Power Board to remove Power Board. ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
6. TROUBLE SHOOTING FLOW CHART (VE710s-4 /VE710b-4 M -star Scaler) 6.1. NO POWER Check Check POWER Check P901,902,903,904 3.3V O/P PANEL STAR P802 5,6 PIN (EA03/03Q Panel C825 P901,902 Only) Check Check I901,T901,T902,Q904, 12V O/P Q905,Q910,Q911 C823 (EA03/03Q Panel Q910,Q911...
Page 43
? Check X101 Crystal 14.318MHz is Change X101 working ? Check I105 Change I105 LCD Pin#70,71 data bus controller IC have signal Check panel Powers VLCD_3V3 VLCD_12V correct Change LCD panel ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 45
14.318MHz(CPT Panel) Change X102 24.576MHz(CMO Panel) is working ? Check I101 Change I101 LCD Pin#73,74 data bus controller IC have signal Check panel Powers VLCD_3V3(CPT Panel) VLCD_5V(CMO Panel) correct Change LCD panel ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 47
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items. Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation.
Page 48
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 49
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 50
BOM LIST (VE710s-4) ViewSonic Model Number: VS-10047 Rev: 1a Serial No. Prefix: PUP Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty E-C-0404-3898 2341110096P CAP,CHIP 125'C CS 0603/COG/50V 10 p J T C101 2346147396P CAP,CHIP 125'C CS 0603/X7R/50V 0.047u K T...
Page 84
11.1. MAIN PCB TOP VIEW (Realtek Scaler CPT Panel) 11.1. MAIN PCB TOP VIEW (Realtek Scaler CMO Panel) ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 85
11.2. MAIN PCB BOTTOM VIEW (Realtek Scaler CPT Panel) 11.2. MAIN PCB BOTTOM VIEW (Realtek Scaler CMO Panel) ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 86
11.3. CON PCB TOP VIEW 11.4. CON PCB BOTTOM VIEW ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Page 87
11.5. POWER PCB TOP VIEW (CPT CLAA170EA08QV / CMO M170E5-L09 Panel) 11.6. POWER PCB BOTTOM VIEW (CPT CLAA170EA08Q / CMO M170E5-L09 Panel) ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...
Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) ViewSonic Corporation VE710s-4_VE710b-4 Confidential - Do Not Copy...