Table of Contents
Advertisement
Timer Recording
Up to 8 timer recording programs can be made using G-
timer programing or Express timer programing method as far as a
year in advance. Remember, the clock must be set before you can
program the timer.
NOTES:
If all the 8 programs have already been set, "PROGRAM FULL"
appears on the TV screen.
After timer recording is completed, the recorder turns off
automatically.
You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
In case of a power failure after programming, the recorder's
memory backup keeps your selections (if the lithium battery is
not exhausted).
G-
System Setup
CODE
INFORMATION
The G-
timer programming system eliminates the need to
CODE
input channel, date, start and stop time data when setting the
timer record function. Simply key in the G-
TV programme you wish to record (found in most TV listings) and
the recorder's timer is automatically programmed.
You have to set "GUIDE PROG" numbers, which are assigned to
each station for purposes of G-
the stations stored in your recorder's memory to get proper results.
Before G-
setup you must have performed the procedures of
CODE
Tuner Set and Clock Set.
IMPORTANT
Perform the following procedure after Auto Set Up and/or the
channel setting steps.
After setting the Guide Program Numbers, channel positions may
be incorrect if you stored or skipped channels. In this case, re-
perform Guide Program Number setting.
Guide Program Number Set
A
Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press
pointer next to "INITIAL SET", then press OK or
B
Access G-
Setup screen
CODE
Press
to place the pointer next to "G-CODE SETUP", then
rt
press OK or
.
e
C
Input Guide Prog number
Press
or the Number keys to select
rt
the Guide Program number as shown in
the TV listing, then press OK or
D
Input receiving channel number
Press
or the Number keys to select
rt
the number of the channel on which the
Guide Program number's broadcasts are
received, then press OK or
e
If the satellite broadcast is received on
your recorder's auxiliary channel ("L-1"
or "F-1"), select "L-1" or "F-1" for the channel position to which
the satellite receiver is connected.
3
4
Repeat steps
and
as necessary.
E
Return to normal screen
Press MENU on the remote control.
CODE
number for the
CODE
timer programming, for all
CODE
to place the
rt
.
e
G-CODE SETUP
GUIDE PROG
TV PROG
2
.
e
[0–9] OR [ / ] : SELECT
[MENU] : EXIT
G-CODE SETUP
GUIDE PROG
TV PROG
2
.
[0–9] OR [ / ] : SELECT
[MENU] : EXIT
G-
CODE
The G-
numbers are the numbers
CODE
next to the program in most TV listing.
Remember, the clock must be set
before you can program the timer.
Be sure to read "G-
Load a cassette with the record safety
tab intact. The recorder turns on, and
the counter is reset, automatically.
Select the appropriate colour system
with "PAL/MESECAM" and "NTSC"
in Function settings.
A
Press PROG on the remote control
to access the G-
G-CODE NO.
[0 – 9]
[+/–] : EXPRESS PROGRAMING
[PROG] : EXIT
B
Press the appropriate Number keys
to input the G-
sure the setting is accurate on the G-
G-CODE NO.
1 2 3 4 5 6 7 8
[0 – 9]
[ ] : DELETE
[PROG] : EXIT
If the G-
after pressing OK, press the Number
keys, PR+/– or
number of the channel on which the
broadcast for the G-
received on the recorder, then press
OK.
To set the tape speed, press SP/LP/EP.
To change the stop time, press STOP+/–.
To timer-record daily (Monday–Friday) or weekly serials,
press DAILY or WEEKLY. Pressing the button again makes the
"DAILY" or "WEEKLY" display disappear.
At the programme check screen...
When the weekly serials are programmed, a day of the week
appears. When the daily serials are programmed, "DAILY"
appears.
If you made a mistake, press & to access the G-
again.
If an incorrect G-
already finished has been inputted, "ERROR" is displayed for
about 5 seconds, then the G-
5
C
Press OK or PROG.
If "PROGRAM OVERLAPPED" appears, see "Program
overlap warning display".
D
Press
. The recorder turns off automatically and "
#
displayed on the display panel.
5
NOTE:
If the tape reaches its end during timer recording, the recording
stops and "
#
Timer Programing
®
".
CODE
screen.
CODE
number, then press OK. Check to make
CODE
CODE
NO. 12345678
START
21:00
DATE
25.04
: [OK]
Setup screen appears
CODE
to input the
rt
number is
CODE
number or the one for a broadcast
CODE
screen reappears.
CODE
", " " and "$" on the front display panel blink.
Program screen.
–
P1 –
STOP
22:00
SP
TV PROG
1
G-CODE SETUP
GUIDE PROG
TV PROG
2
5
[0–9] OR [ / ] : SELECT
[PROG] : EXIT
screen
CODE
" is
#
Advertisement
Table of Contents
