Table of Contents
Advertisement
– Other Functions –
AUTO SP LP TIMER — ON / OFF
When this function is set to "ON", the recorder automatically
switches to LP mode to allow complete recording if there is not
enough tape to record the entire program while timer-recording in
SP mode.
For Example, Recording a PAL-broadcast programme of 210
minutes in length onto a 180-minute tape.
Approximately 150 minutes
SP mode
Total 210 minutes
NOTES:
● If you have programed the recorder to timer-record 2 or more
programs, do not use this function, but change the tape speed
manually during timer programing.
● There may be some noise and sound disturbance where the tape
speed switches from SP to LP mode on the tape.
● The Auto SP LP Timer feature is not available during ITR
(Instant Timer Recording), and the feature will not work properly
with any tapes longer than E-180 or with some tapes of shorter
lengths.
Multi-Brand Remote Control
This remote control can control some functions of remote
controllable TVs, cable boxes, satellite receivers or DVD sets
listed below. Without setting, you can control a JVC TV.
NOTES:
● Some unit's brands have more than one code. If the unit does
not function with a specified code, try other codes.
● Depending on the type of unit, some or all functions cannot be
operated using this remote control.
● It's not possible to operate a unit not equipped with a remote
sensor.
● It's not possible to set the remote control for two units at the
same time.
● Once you have set the remote control to operate the unit, you
do not have to set it until you replace the batteries from the
remote control.
Approximately 60 minutes
LP mode
TV Brand Setting
Turn on TV
Turn on the TV using the Power button on the TV or its remote
control.
Set TV brand code
Press and hold TV.
Press the Number keys to enter your TV's brand code.
Press OK, and release TV. The TV should turn off.
Operate TV
First, press TV to set the remote control to TV mode, then press
one of the following buttons:
(TV Muting), TV
+/–, and the Number keys.
● For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
TV BRAND
CODE
JVC
01, 23, 24, 25
AIWA
36
BEIJING
22
CCE
02
CHANGHONG
34
DAEWOO
17, 37
FERGUSON
27
FINLUX
30
FUNAI
32
GRADIENTE
15
GRUNDIG
19
HITACHI
10
ITT
28
JINXING
38
KONKA
40
LG/GOLDSTAR
18
Cable Box, Satellite Receiver or DVD Brand Setting
Turn on the unit
Turn on the cable box, satellite receiver or DVD using the Power
button on the unit or its remote control.
Enter brand code
Press and hold CABLE/SAT/DVD.
Press the Number keys to enter your unit's brand code.
Press OK, and release CABLE/SAT/DVD.
Operate the unit
First, press CABLE/SAT/DVD to set the remote control to cable
box, satellite receiver or DVD mode, then press one of the
following buttons:
For satellite receiver and cable box . . .
, TV PR+/–, Number keys.
For DVD. . .
, PLAY ( ), STOP ( ), PAUSE ( ), FF (
(
) keys.
● For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
● To change the unit's channels, press TV PR+/– or the Number
keys. (The PR+/– button can be used to change the recorder's
channels only.)
, TV/VCR, TV PR+/–,
TV BRAND
CODE
MITSUBISHI
03
MIVER
29
NEC
20
NOBLEX
22
NOKIA
31
PANASONIC
04, 11
PEONY
34, 38, 39
PHILICO
10, 17, 21
PHILIPS
02, 42
SAMSUNG
12, 33, 34, 35
SANYO
13, 16
SHARP
06
SONY
07
TCL
41
THOMSON
26
TOSHIBA
08, 14
), REW (
),
Advertisement
Table of Contents
