Table of Contents
Advertisement
ELECTRICAL-BODY AND CHASSIS 12-15
Fig. 21 - Qlal Quadrant Assembly ~ Camaro
SEAT SEPARATOR CONSOLE LAMPS
COMPARTMENT LAMP REPLACEMENT (Fig. 22)
1. Remove (pry up) switch assembly from console open-
ing in.the instrument compartment.
2. Remove bulb from the socket.
3. Replace bulb and install switch assembly in console
opening.
COURTESY LAMP REPLACEMENT (Fig. 22)
1. Remove two screws and lens at rear of console.
2. Remove bulb from retainer.
3. Replace the bulb, position the lens and install attach-
ing screws.
QUADRANT LAMP REPLACEMENT (Fig. 22)
1. Remove Dial Quadrant Trim plate retaining screws
and lift trim plate assembly from console opening.
2. Disconnect lamp socket from the retainer and re-
move bulb from the socket.
3. To install, insert bulb into the socket and snap the
socket assembly into the retainer.
Position the trim plate assembly into the console
opening and install the retaining screws.
4.
LIGHTING SWITCH REPLACEMENT (Fig. 24)
1. Disconnect battery ground cable.
2. Pull control knob out of headlamp ON position.
3. Reach under instrument panel and depress the switch
shaft retainer (Fig. 25) and remove knob and shaft
assembly.
4. Remove ferrule nut using Tool J-21932 and remove
switch assembly from instrument panel.
NOTE:
Some Chevelle models require use of
ToolJ-4880.
5. Disconnect the multi-plug connector from the lighting
switch. A screw driver may be inserted in the side
of the switch to pry the connector from the switch.
6. Connect the multi-plug connector to the replacement
switch (Fig. 23). Connect battery cable to battery
terminal and check operation of the light switch'in all
positions.
NOTE:
Ground switch- to check dome lamp
operation.
7. Position switch and bezel to panel mounting hole and
install ferrule jmt.
8. Insert switch control knob and shaft assembly into
switch until retainer engages shaft.
WIPER SWITCH REPLACEMENT (Fig. 26)
1. Disconnect battery ground cable.
2. Remove the connectors from the rear of the switch.
NOTE:
On Air Conditioned models it is nec-
essary to remove left A/C outlet duct for acces-
sibility to rear of switch.
3. Loosen set screw and pull knob from switch shaft.
4. Remove retaining nuts using special Tool J-21932
and withdraw wiper switch from behind console.
NOTE:
Some Chevelle models require special
ToolJ-4880.
5. To install, reverse removal procedure and check
operation of wipers.
STOPLIGHT SWITCH REPLACEMENT (Fig. 27)
1. Disengage retaining fingers, disconnect wiring har-
ness connector from switch and unscrew switch from
mounting clip.
2. Depress brake pedal and push new switch into clip
until shoulder bottoms out against clip.
3. Check switch position for proper operation. Elec-
trical contact should be made when the brake pedal is
depressed 3/8" to 5/8" from fully released position.
DIMMER SWITCH REPLACEMENT (Fig. 28)
1. Fold back upper left corner of front floor mat, disen-
gage connector lock fingers, and disconnect multi-
plug connector from dimmer switch.
2. Remove two screws retaining dimmer switch to toe
pan.
3. Connect multi-plug connector to new switch and
check operation. Install new switch to toe pan with
two screws. Replace floor mat.
BACKING LAMP SWITCH REPLACEMENT
Located on Mast Jacket (Fig. 29)
1. Disconnect wiring connector at switch terminals.
2. Remove switch attaching screws and switch from
mast jacket.
3. Position new switch to mast jacket, install the re-
taining screws and connect wire connector to switch.
NOTE:
Position gear shift in neutral before
assembling switch to mast jacket.
4. Check operation of switch.
Located on Transmission (Fig. 30)
1. Raise and support vehicle.
CHEVROLET CHASSIS SERVICE MANUAL
Advertisement
Table of Contents
