Operating Jvc's Audio/Video Components; Operating Audio Components - JVC RX-DP9VBK Instructions Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.

Operating Audio Components

IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK (SYNCHRO) jacks (see page 47) in addition to the
connections using cables with RCA pin plugs (see pages 9 and 10).
• Aim the remote control directly at the remote sensor on the receiver.
• To operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 22.)
• Refer also to the manuals supplied with your components.
When using the remote control:
– Check the indication shown on the remote's display when you press
a button—this indicates the remote control operation mode for a
while (10 or 5 seconds).
– The CONTROL button can change the remote control operation
mode without changing the source.
Each time you press the button, the remote control operation mode
changes in the sequence—VCR1 = TAPE = CDR = CDDSC = (back
to the beginning).
Ex. When you press FM.
55
STANDBY ON
TV/CATV/DBS VCR 1
STANDBY/ON STANDBY/ON
Tuner
You can always perform the following operations:
FM : Tunes into the last selected FM station.
AM : Tunes into the last selected AM station.
After pressing FM or AM, you can perform the following
operations:
1 – 10, +10 : Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then
10.
TUNING UP/DOWN : Tunes into stations.
FM MODE : Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations:
THX ON/OFF
: Turns on or off the THX Surround
SURROUND ON/OFF
: Turns on or off the conventional
DSP MODE
: Selects the DSP modes.
TEST : Turns on or off the test tone output.
After pressing SOUND, you can perform the following operations:
FRONT•L then LEVEL +/– : Adjusts the left front speaker
FRONT•R then LEVEL +/– : Adjusts the right front speaker
SUBWFR then LEVEL +/– : Adjusts the subwoofer output level.
CENTER then LEVEL +/– : Adjusts the center speaker channel
SURR•L then LEVEL +/– : Adjusts the left surround speaker
SURR•R then LEVEL +/– : Adjusts the right surround speaker
SURR BK•L then LEVEL +/– : Adjusts the left surround back
SURR BK•R then LEVEL +/–: Adjusts the right surround back
EFFECT
: Selects the effect level.
ROOM SIZE : Selects the room size.
LIVENESS
: Selects the liveness.
WALL : Selects the wall type.
LINE DIRECT
: Turns on or off Line Direct.
CC CONVERTER
: Turns on or off CC Converter.
Notes:
• After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the 10 keys;
otherwise, the 10 keys cannot be used for operating your target
source.
• Each time you press LEVEL + or LEVEL –, the corresponding
speaker name appears on the remote's display.
modes—THX Surround EX or THX
Cinema.
Surround modes—Dolby Digital,
DTS Surround, and Dolby Pro
Logic.
channel output level.
channel output level.
output level.
channel output level.
channel output level.
speaker channel output level.
channel speaker output level.