JVC RX-DP10VBK Instructions Manual page 75

4. Press one of the learning buttons, to which you
want to assign a signal from the target remote
control.
The LEARN indicator starts flashing.
• If you have pressed DVD or DVD MULTI in step 3, you can
store the signals into the following buttons.
EFFECT
1 2 3
ROOM SIZE
4 5 6
LIVENESS
7 8 9
/P
WALL
10 0 + 10
100 +
RETURN
FM MODE
• If you have pressed PHONO in step 3, you can store the
signals into the following buttons.
PLAY
TUNING
STOP
• If you have pressed CD, or CONTROL to select "CD DISC,"
in step 3, you can store the signals into the following buttons.
– You can store a different set of signals into the following
buttons separately for "CD" and "CD DISC."
EFFECT
1 2 3
ROOM SIZE
4 5 6
LIVENESS
7 8 9
/P
WALL
10 0 10
+
100 +
RETURN FM MODE
• If you have pressed "TAPE/MD" or "CDR" in step 3, you can
store the signals into the following buttons.
EFFECT
1 2 3
ROOM SIZE
4 5 6
LIVENESS
7 8 9
/P
WALL
10 0 + 10
100 +
RETURN FM MODE
• If you have pressed VCR1 in step 3, you can store the signals
into the following buttons.
VCR 1
STANDBY/ON
EFFECT
1 2 3
ROOM SIZE
4 5 6
LIVENESS
7 8 9
/P
WALL
10 0 10
+
100 +
RETURN FM MODE
/ REW PLAY
FF/
DOWN TUNING UP
STOP PAUSE
SET
DVD
MENU
/ REW PLAY
FF/
DOWN TUNING UP
STOP PAUSE
/ REW PLAY FF/
DOWN TUNING UP
REC STOP PAUSE
/ REW PLAY
FF/
DOWN TUNING UP
STOP PAUSE
REC
CHANNEL
• If you have pressed "TV/DBS" in step 3, you can store the
signals into the following buttons:
– By setting the TV operation mode selector
either to "TV" or "CATV/DBS," you can store
a different set of signals into the following
buttons.
TV/CATV/DBS
STANDBY/ON
EFFECT
1 2 3
ROOM SIZE
4 5 6
LIVENESS
7 8 9
/P
WALL
10 0 + 10
100 +
RETURN FM MODE
5. While the LEARN indicator is flashing, press the
button on the target remote control.
The signal from the target remote control is sent to this remote
control.
"LEARN OK" appears and the LEARN indicator stops flashing
and remains lit. The target signal is now stored in the button
selected in step 4.
Notes:
• If the LEARN indicator stops flashing before you press the
button on the target remote control, repeat from step 4 again.
• If "ERROR" appears on the display, you have failed in storing
the signal. Try again. However some signals do not match to
this remote control even though this remote control can learn
most infrared signals.
6. • Repeat steps 4 to 5 to store more signals in the
same remote mode (source).
• Repeat steps 3 to 5 to store more signals in a
different remote mode (source).
7. Set the LEARN/TRANSMIT (MAIN ROOM/
SUB ROOM) selector to "TRANSMIT (MAIN
ROOM/SUB ROOM)" to finish the storing
procedure.
LEARN TRANSMIT
MAIN ROOM SUB ROOM
For the main room
operations
Notes:
• The signals stored into this remote control from the target remote
control deviate slightly from the original signals. Since some
components will not accept these deviating signals, you may not be
able to operate those components using this remote control even
though the storing procedure has been successfully finished.
• When replacing the batteries, finish it without delay; otherwise, the
stored signals are all erased.
TV
CATV/
DBS
TV/VIDEO
TV VOL CHANNEL
LEARN
LEARN TRANSMIT
MAIN ROOM SUB ROOM
For the sub-room
operations
72