Listening To Fm And Am (Mw) Broadcasts; Tuning In To A Station; Presetting Stations - JVC CA-UXHB4 Instructions Manual

Listening to FM and AM (MW) Broadcasts

Tuning in to a Station

You can search for the station by either automatically or
manually.
Auto Tuning
1
Press FM/AM/DAB repeatedly to
select either "FM" or "AM (MW)."
The unit automatically turns on and tunes in to
the previously received station.
• If the station previously selected is stored in a preset
number, the preset number will also appear.
2
Press and hold ¢ or 4 (or
SCROLL UP ¢ or SCROLL
DOWN 4 on the unit) for
about 2 seconds until "Search.."
appears on the display.
"Searching.." appears and the unit starts searching
for stations.
• ¢ (SCROLL UP ¢):
• 4 (SCROLL DOWN 4): Decreases the frequencies.
The search stops when a station of sufficient signal
strength is tuned in.
• If an FM program is broadcast in stereo, the ST (stereo)
indicator lights up on the display (only when the
reception is good).
To stop during searching, press ¢ or 4 (or SCROLL
UP ¢ or SCROLL DOWN 4 on the unit).
Manual Tuning
1
Press FM/AM/DAB repeatedly to
select either "FM" or "AM (MW)."
2
Press and hold ¢ or 4 (or
UP ¢ or DOWN 4 on the
unit) for more than 3 seconds.
• ¢ (SCROLL UP ¢):
• 4 (SCROLL DOWN 4): Decreases the
The frequency keeps changing quickly.
To stop during searching, release the button.
When you repeatedly press ¢ or 4 (or SCROLL
UP ¢ or SCROLL DOWN 4 on the unit)
The frequency changes step by step.
21
FM/AM/DAB
UP
SEARCH/ SEARCH/
SCROLL SCROLL
PRESET
DOWN UP
GROUP
/
SELECT
DOWN
PRESET
GROUP
Increases the frequencies.
FM/AM/DAB
UP
SEARCH/ SEARCH/
SCROLL SCROLL
PRESET
DOWN UP
GROUP
/
SELECT
DOWN
PRESET
GROUP
Increases the
frequencies.
frequencies.
To change the FM reception mode
On the remote control ONLY:
When an FM stereo broadcast is hard to receive
or noisy, press FM MODE so that the "Mono"
appears on the display. Reception will improve.
To restore the stereo effect, press FM MODE
again so that "Stereo" appears and the ST (stereo) indicator
lights up on the display. In stereo mode, you can hear stereo
sound when a stereo program is broadcast.
The stereo effect also restores when:
• changing the band (AM (MW), or DAB).
• changing the station frequency.
• changing the playing source.
• turning off (or on) the unit.

Presetting Stations

You can preset 20 FM and 10 AM (MW) stations manually.
In some cases, test frequencies have been already stored
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction. You
can preset the stations you want into memory by following
the presetting method.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start again from step 2 .
On the remote control ONLY:
1
Tune in to the station you want to preset.
• See "Tuning in to a Station" on the left column.
2
Press PROGRAM.
An available preset number starts flashing on the
display.
3
Press PRESET GROUP
PRESET GROUP
preset number, then press
PROGRAM.
"Station Stored" appears and the preset station
is stored in memory.
REPEAT
/FM MODE
PROGRAM
UP
SEARCH/
SCROLL
or
PRESET
DOWN
GROUP
to select a
/
SELECT
DOWN
PRESET
GROUP
SEARCH/
SCROLL
UP