Using The Remote Control For Operating Jvc's Audio/Video Components - JVC RX-772VBK Instructions Manual

Using the Remote Control for Operating JVC's Audio/Video Components

RM-SR772U REMOTE CONTROL
VCR AUDIO
TV/CATV
POWER SLEEP POWER
/SAT POWER
VIDEO VCR TAPE
TV FM/AM CD PHONO
SOUND
ONE TOUCH
DELAY CNTR
OPERATION
1 2 3
CD
TEST REAR
DISC
4 5 6
CD
TRACK
7 8 9
/P
SOUND
SEA MODE SURR MODE
CONTROL
10 0
+10
RETURN FM MODE/MUTE 100+
AUDIO/TV
/VCR
CATV
/SAT
CONTROL
TAPE VCR
MENU MENU
EXIT
You can operate JVC's audio and video components with this receiver's remote control, since control signals
for JVC components are preset in the remote control.
Notes:
• If you use the buttons on the front panel or the menu function to choose a source, the remote control will
not operate that source. To operate a source with the remote control, the source must be selected using
buttons on the remote control.
• Check to see if its remote control mode selector is set to the correct position. To operate audio system, TVs,
and VCRs, set it to the "AUDIO/TV/VCR" position.
• Refer also to the manuals supplied with your components.
IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks
(see page 35) in addition to the connections using cables with RCA pin plugs (see page 8).
• Aim the remote control directly at the remote sensor on the receiver.
Tuner
After pressing FM/AM (with the remote control mode selector set to the "AUDIO/TV/VCR" position), you
can perform the following operations:
FM/AM: Alternates between FM and AM.
1 — 10, +10: Selects a preset channel number directly.
For channel number 5, press 5. For channel number 15, press +10, then 5. For channel
number 20, press +10, then 10.
FM MODE/MUTE: Changes the FM reception mode.
Sound control section (Amplifier)
After pressing SOUND CONTROL (with the remote control mode selector set to the "AUDIO/TV/VCR"
position), you can perform the following operations:
SEA MODE: Changes the SEA modes.
SURR MODE: Changes the surround modes.
CNTR +/–: Changes the center speaker output level for the surround modes.
REAR +/–: Changes the left/right rear speaker output level for surround modes.
DELAY: Changes the delay time for surround modes.
TEST: Checks the speaker output level for surround modes.
Note:
After adjusting sounds, press the corresponding source selecting button (FM/AM, CD, CD TRACK, CD DISC,
VCR or TV SOUND) to operate your target source by using 10 keys; otherwise, 10 keys cannot be used for
operating your target source.
CD player
After pressing CD or CD TRACK (with the remote control mode selector set to the "AUDIO/TV/VCR"
position), you can perform the following operations on a CD player:
PLAY: Starts playing.
4 4
4 4 4 :
Returns to the beginning of the current (or previous) track.
¢ ¢
¢ ¢ ¢ :
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
1 — 10, +10: Selects a track number directly.
To select track number 5, press 5. For track number 15, press +10, then 5. For track number 20,
press +10, then 10. For track number 30, press +10, +10, then 10.
Note:
You can use either the CD button or the CD TRACK button to activate the buttons listed above. If you press
CD, the playing source also changes to "CD." On the other hand, if you press CD TRACK, the playing source
does not change to "CD."
CD player-changer
After pressing CD DISC (with the remote control mode selector set to the "AUDIO/TV/VCR" position), you
can perform the following operations on a CD player-changer:
PLAY: Starts playing.
4 4 : 4 4 4
Returns to the beginning of the current (or previous) track.
¢ : ¢ ¢ ¢ ¢
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press the PLAY button.
1 — 6, 7/P: Select the number of a disc installed in a CD player-changer.
After pressing CD TRACK:
1 — 10, +10: Selects a track number directly.
To select track number 5, press 5. For track number 15, press +10, then 5. For track number 20,
press +10, then 10. For track number 30, press +10, +10, then 10.
Page 38