JVC CA-MXJ200 Instructions Manual page 36

Amplifier connection
Verstärkeranschluß
Raccordement à l'amplificateur
Aansulaiten op de versterker
Anslutning till en förstärkare
Conexión al amplificador
Collegamento dell'amplificatore
Forstærkertilslutning
Vahvistimen liitäntä
Połączenia ze wzmacniaczem
Erősítő csatlakoztatás
Zapojení zesilovače
Right speaker
Rechter Lautsprecher
Enceinte droite
Amplifier output terminals
Rechter luidspreker
Ausgang des Verstärkers
Altavoz derecho
Bornes de sortie de l'amplificaterur
Altoparlante destro
Uitgangsaansluitengen van de versterker
Höger högtalare
Terminales de salida de amplificador
Højre højttaler
Terminali de uscita dell'amplifcator
Oikeanpuoleinen kaiutin
Utgångar på förstärkaren
Prawa kolumna
Forstærkerudgangsbøsninger
Jobb hangszóró
Vahvistimen ulostuloliittimet
Pravý reproduktor
Przyłącza wyjścia ze wzmacniacza
Erősítő kimeneti csatlakozók
Výstupní zdířky zesilovače
SPEAKERS
RIGHT
Black
Schwarz
Noir
Zwart
Negro
Nero
Left speaker
Linker Lautsprecher
Enceinte gauche
Linker luidspreker
Altavoz izquierdo
altoparlante sinistro
Vänster högtalare
Venstr højttaler
Vasemmanpuoleinen kaiutin
Lewa kolumna
Bal hangszóró
Levý reproduktor
LEFT
Svart
Sort
Musta
Czarny
Fekete
Černý
CONNECTION
• Turn off power to the whole system before connecting the
speakers to the amplifier.
• The nominal impedance of the SP-MXJ300, SP-MXJ200 is 6
. Select for use an amplifier to which a speaker system with
the load impedance of 6
• The maximum power handling capacity of the SP-MXJ300 is
100W and the SP-MXJ200 is 60W. Excessive input will result
in abnormal noise and possible damage. In cases where the
signals described below are applied to the speakers, even if
the signals are below the maximum allowable input, they may
cause an overload and burn the wiring of the speakers. Be
sure to lower the amplifier volume beforehand.
1) Noise during FM tuning.
2) High level signals containing high frequency components
produced by a tape deck in the fast forward mode.
3) Click noise produced when turning power of other compo-
nents on and off.
4) Click noise produced when connecting or disconnecting
cords with the power on.
5) Click noise produced when the cartridge is replaced with
the power on.
6) Click noise produced when operating amplifier switches.
7) Continuous high frequency oscillation or high pitch electroni-
cally produced musical instrument sound.
8) Howling when using a microphones.
SPECIFICATIONS
Type
Speaker units
Woofer
Tweeter
Power Handling Capacity
SP-MXJ300
SP-MXJ200
Impedance
Frequence Range
Sound Pressure Level
Dimensions (W H D)
Mass
Design and specifications subject to change without notice.
2
2
can be connected.
: 2-way 2-speaker bass-reflex
type
: Dual Duct System
: 16 cm (6-5/16 in.) cone
: 4 cm (1-5/8 in.) cone 1
: 100 W
: 60 W
: 6
: 45 Hz - 22 000 Hz
: 88 dB/W·m
: 215 mm 315 mm 273 mm
(8-1/2 in. 12-7/16 in. 10-3/4 in.)
: 3.5 kg (7.8 lbs) each
1