Table Of Contents - Furuno FCR-2139S-BB Installation Manual

Table of Contents

Table Of Contents1
Safty Instructions3
Radio Frequency Radiation Hazard3
System Configuration5
Category Of Units5
Equipment Lists6
Standard Supply6
Optional Supply7
About The Category Sticker9
Sticker For Category9
Mounting11
Antenna Unit11
Mounting Consideration11
Installation Precaution For S-Band Antenna Unit13
Antenna Unit Assembling14
Antenna Unit Assembling Procedure14
How To Lift The Antenna Unit15
Fastening The Antenna Unit To The Mounting Platform15
Attachment Of Lifting Fixtures, Collar And Ropes15
Installation Of Reinforcement Ribs16
Bottom View16
Mounting Of Antenna Unit17
Ground Terminal Provided On Antenna Base17
Monitor Unit18
Radar Control Unit/Trackball Control Unit18
Ex. Ecdis Control Unit, Bottom View Rcu-0218
Desktop Mounting19
Fixing With Kb Fixing Metal19
Fixing Without Kb Fixing Metal19
Side View Of Control Units19
Flush Mounting20
For Rcu-02520
For Rcu-02620
Radar Processor Unit21
Mounting Procedure21
Floor Mounting Or Bulkhead Mounting21
Processor Unit21
Mounting Considerations21
Processor Unit, Front View22
How To Mount The Processor Unit23
How To Mount The Sensor Adapter24
Sensor Adapter Mc-3000S/3010A/3020D/3030D (Option)24
Intelligent Hub Hub-3000 (Option)25
Hub-3000, Bottom View25
How To Mount The Intelligent Hub Hub-300025
Switching Hub Hub-100 (Option)26
Wiring27
Interconnection27
Notice For The Network Construction27
Notice On Wiring27
Antenna Unit, Bow View28
Shield Wire29
Coaxial Cable29
Wiring For Wago Connector30
Wiring For Coaxial Cable30
Fabricating Power Cable Tpycy-2.531
Passing Clamping Gland, Washers And Gasket On Power Cable Tpycy-2.531
Fabricating The Power Cable32
Antenna Unit, Left View32
Connection Of Cables33
Location Of Connectors34
Signal Cable Rw-960035
Other Cables For Optional Units35
Connection Of Sub-Display36
How To Connect Cables To Terminals On The Processor Unit36
Cables Connected At The Wiring Plate 137
Cables Connected At Wiring Plate 2 Assy37
Fabricating Lan Cable38
Ipx2 Kit39
Contents Of Ipx2 Kit39
How To Connect Cables Inside The Processor Unit40
Fabrication40
Fabrication Of Ttycs Series40
Fabrication Of Ttycsla Series40
Processor Unit, Top View41
Example Of Wiring (Inside The Processor Unit)42
How To Set Jumper Blocks On I/O Board43
How To Set The Termination Resistors43
Processor Unit, I/O Board (24P0124)43
How To Select The Serial Input/Output Format44
Connector J344
Connector J444
Connector J544
Connector J645
Connector J745
Connector J845
Connector J945
How To Set Contact Input/Output46
Setting For Contact Input46
Setting For Voltage Input46
Connector J1146
Standard Type47
Slide Switch48
How To Open The [Installation Setting] Menu48
Power Supply Unit48
Sensor Adapters (Option)49
How To Attach The Rod Terminal (Ferrule Type)49
Mc-3000S50
Lan Cable (Fr-Ftpc-Cy)50
Ttycs-1Q Cable50
Ttycsla-1Q Cable50
Ttycs-1 Cable51
Ttycsla-1 Cable51
Ttycs-4 Cable51
Ttycsla-4 Cable51
Connections52
How To Set Nc/No Output (J2)52
Connector J252
How To Set Input Specification (J4 To J9)53
Case Packing Op24-2855
Mc-3010A/3020D/3030D56
Mc1.5-W-L600/1000/2000/3000 Cable56
Ttycsla-1 (Mc-3010A)56
Connection57
Input Method (Mc-3010A Only)57
Power Voltage58
Power Current58
How To Set Ack Input (Mc-3020D)59
Input Circuit For Voltage Input59
Input Circuit For Contact Input59
How To Set Alarm Output (Mc-3030D)61
Case Packing Op24-2963
How To Set Jumper Blocks In The Sensor Adapters64
Mc-Cs Board (24P0114)64
Jumper Block64
Termination Resistor On65
Terminal Resistor Off65
Mc-Din Board (24P0116)66
Mc-Out Board (24P0117)66
Mc-Anlg Board (24P0115)66
How To Extend The Control Unit Cable (Option)69
Radar Control Unit (Rcu-025)69
Trackball Control Unit (Rcu-026)71
Setting And Adjustment73
Radar Setting73
How To Access To The Installation Manual73
Heading Alignment73
Adjustment Sweep Timing74
Suppressing Main Bang74
Other Settings75
Echo Adj Menu Setting75
Cable Att Adj75
Ring Suppression75
Installation Menu Setting76
Range Unit76
Type76
On Time And Tx Time76
Qv Echo Level77
Tt W/O Gyro77
Acq Preset77
Track Preset77
Other Menu Setting78
Demo Echo78
Eav W/O Gyro78
Tt Category Select78
Gyro Converter Gc-1079
Installing The Gyro Converter Board79
Installing Optional Equipment (For Radar)79
Attaching The Gyro Converter Board In The Radar Processor Unit80
Connection For P60881
Connection For J60281
Connecting Connector Assemblies81
Connection Of External Power Supply82
Attaching Plastic Cover For Gyro Converter Board82
Dip Switch, Jumper Wire Settings83
Connection Of External Power Supply To Gyro Converter Board83
Gyrocompass Type84
Frequency84
Rotor Voltage84
Ratio84
Setting Method 2: By Maker And Model Of Gyrocompass85
Location Of Dip Switches, Jumper Wires On The Gyro Converter Board86
Gyro Converter Board86
Setting The Heading Readout On The Radar Display87
Junction Box87
Cable Fabrication88
Input/Output Data91
Iec 61162 Sentences92
Input Sentence And Priority92
Core Type93
Armor Type93
Appendix 1 Jis Cable Guide93
Rod Terminals94
Mc-3000S, Mc-Cs Board (24P0114)94
Appendix 2 Rod Terminals95
Mc-3010A Mc-Analg Board (24P0115)96
Mc-3020D, Mc-Din Board (24P0116)97
Mc-3030D, Mc-Dout Board (24P0117)99
Packing List100
Interconnection Diagram129