To Order Parts 1. Write your full name and complete address on the 5. Send or bring the order to an authorized Textron Turf order. Care And Specialty Products Dealer. 2. Explain where and how to make shipment. 6. Inspect all shipments on receipt. If any parts are dam- aged or missing, file a claim with the carrier before 3.
Suggested Stocking Guide To Keep your Equipment fully operational and productive, maintain a stock of the more commonly used maintenance items. We have included part numbers for additional support materials and training aids. A more complete listing of accessories and attachments can be found in the Specifications Section Service Parts Qty.
SAFETY SAFETY OPERATING SAFETY ______________________________________________________ WARNING EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS. Familiarize yourself with the location and proper use of all controls. Inexperienced operator’s should receive instruction from someone familiar with the equipment before being allowed to operate the machine. Safety is dependent upon the awareness, concern and Never disconnect or bypass any switch.
Adjustments and maintenance should always be performed by a qualified technician. If additional information or service is needed, contact your Authorized Jacobsen Dealer who is kept informed of the latest methods to service this equipment and can provide prompt and efficient service. Use of other than original or authorized Jacobsen parts and Accessories will void the warranty.
(1.65 mm / 1 kph) Reel Width ...... 22 in. (559 mm) ACCESSORIES ___________________________________________________________ Refer to the Parts Catalog and contact your area Jacobsen Dealer for a complete listing of accessories and attachments. TRACTOR REELS Air Blow Gun ............ JAC5098 LF 3400, LF 3400 Turbo Orange Touch-up Paint (12 oz.
ADJUSTMENTS ADJUSTMENTS GENERAL ________________________________________________________________ cannot be made, contact an authorized Jacobsen WARNING Dealer. Replace, do not adjust, worn or damaged components. To prevent injury, lower implements to the ground, disengage all drives, engage parking brake, stop engine Do not wear jewelry or loose fitting clothing when and remove key from ignition switch before making any making adjustments or repairs.
ADJUSTMENTS BEDKNIFE ADJUSTMENT ___________________________________________________ Read Section 3.2 before making the adjustment. Note: Avoid excessive tightening or damage may occur to bedknife and reel blades. Reels must turn freely. CAUTION To prevent personal injury and damage to the cutting edges, handle the reel with extreme care Start adjustment at leading end of reel, followed by the trailing end.
ADJUSTMENTS FLASH ATTACH ___________________________________________________________ Installing Cutting units Carefully raise arm until cutting unit can be removed. Place each cutting unit in front of its respective lift arm. Raise lift arm and position cutting unit so that yoke (T) is in line with swivel housing (S). Carefully lower arm onto yoke.
ADJUSTMENTS MOW SPEED _____________________________________________________________ Cutting quality is better at speeds well below the transport speed of the tractor. An initial mow speed of five to six mph is set at the factory and should be satisfactory for most cutting conditions. Local turf conditions however may respond better to a different speed.
ADJUSTMENTS 3.10 NEUTRAL ADJUSTMENT ___________________________________________________ Neutral adjustment can only be made at the drive pump. Connect traction linkage. When connecting linkage at traction pedal make sure pointer on traction pedal The neutral adjustment is preset at the factory on all new bracket is centered over neutral switch (M -Figure 3K).
ADJUSTMENTS 3.12 FRONT REEL LIMIT SWITCH ________________________________________________ The front left and right lift arms are equipped with proximity Start engine and check that reels turn off when raised. switches which signal the controller to turn off the reels.The Note: The reed switches set the point where the reels switches are mounted to the tractor frame directly behind turn off, not how high they will raise.
All torque values included in these charts are approximate and are for reference only. Use of these torque values is at your sole risk. Jacobsen is not responsible for any loss, claim, or damage arising from the use of these charts.
If proper adjustments Use the illustrations in the Parts Catalog as reference cannot be made, contact an Authorized Jacobsen for the disassembly and reassembly of components. Dealer. Recycle or dispose of all hazardous materials Inspect the equipment on a regular basis, establish a (batteries, fuel, lubricants, anti-freeze, etc.) according...
MAINTENANCE AIR FILTER _______________________________________________________________ Check the service indicator daily. If red band appears in the Reassemble cap making sure it seals completely window (B) replace the element. around the filter housing. Dust evacuator must be facing down. Do not remove the element for inspection or cleaning. Check all hoses and air ducts.
MAINTENANCE BATTERY ________________________________________________________________ Make absolutely certain the ignition switch is “Off” and the When installing the battery, always assemble the RED, positive (+) battery cable first and the ground, BLACK, key has been removed before servicing the battery. negative (-) cable last. When removing the battery, always remove the CAUTION ground, BLACK, negative (-) cable first and the RED,...
4.12 HYDRAULIC OIL___________________________________________________________ Refer to Section 6.2 for specific maintenance intervals. After oil has drained install drain plug and fill with Jacobsen Hydraulic oil. Drain and replace the hydraulic oil after a major component Purge air from system. failure, or if you notice the presence of water or foam in the oil, or a rancid odor (indicating excessive heat).
If the interlock does not function properly and the problem cannot be corrected, contact an authorized Jacobsen Dealer. Keep the wire harness and all individual wires away from moving parts to prevent damage. Make sure the seat switch harness is connected to the main wire harness.
If you have to add coolant more than once a month, or Check coolant level daily. Radiator should be full and add more than one quart at a time, have a Jacobsen recovery bottle should be up to the cold mark.
Use compressed air to clean engine and radiator fins. A Repair damaged metal surfaces and use Jacobsen touch-up special blow gun is available through Jacobsen Dealer. paint. Wax the equipment for maximum paint protection.
MAINTENANCE 4.20 REEL BACKLAPPING ______________________________________________________ WARNING To prevent severe injury, keep hands, feet and clothing away from rotating reels. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate the engine without proper ventilation Check the reel and bedknife to determine if backlapping or grinding will restore the cutting edge.
MAINTENANCE 4.21 STORAGE________________________________________________________________ General After Storage Wash the tractor thoroughly and lubricate. Repair and Check and reinstall battery paint damaged or exposed metal. Check or service fuel filter and air cleaner. Inspect the tractor, tighten all hardware, replace worn Check the radiator coolant level. or damaged components.
TROUBLESHOOTING TROUBLESHOOTING GENERAL ________________________________________________________________ The troubleshootijng chart below lists basic problems that may occur during start-up and operation. For more detailed information regarding the hydraulic and electrical systems contact your area Jacobsen Dealer. Symptoms Possible Causes Action Engine will not start.
TROUBLESHOOTING CONTROLLER LAMPS _____________________________________________________ The controller is a solid state device that monitors and indicates an active circuit and will turn an input lamp on, an controls electrical functions. The controller receives input open switch an inactive circuit and will turn a lamp off. signals from various switches and sensors throughout the Outputs are active when their lights are on.
TROUBLESHOOTING ELECTRICAL CIRCUITS ____________________________________________________ When troubleshooting the machine using the controller always check that Program Active lamp (1) is on. These indicate that the controller has power and the program is active. Note: The controller requires a minimum of six volts to operate.
*** Inspect visible hoses and tubes for leaks or oil marks. Pack bearings with NLGI Grade 2 (Service Class GB) Manual grease gun with NLGI Grade 2 (Service Class LB). III Engine Oil - See Section 4.3 IV Jacobsen Hydraulic Oil - SAE 10W30 or Greens Care 68 GB-28...
MAINTENANCE & LUBRICATION CHARTS LUBRICATION CHART______________________________________________________ 11 13 Grease points same for all reels Grease Fittings F1 - 50 Hours (Every Week) Swivel Housing Lift Arm Lift Cylinders Lift Arm Pivot Brake Pedal Pivot Traction Pedal Pivot Ball Joint Steering Pivot Steering Cylinder 10 Axle Pivot F2 - 100 Hours...
Page 30
Para hacer pedidos de piezas 1. Escribir el nombre y dirección completos en el pedido. 5. Enviar o llevar el pedido a un Distribuidor autorizado Textron Turf Care And Specialty Products. 2. Explicar a dónde y cómo hacer el envío. 6.
Page 31
Guía de Inventario Sugerido Para mantener su Equipo en perfecta operación y producción, mantenga un inventario de los componentes usados con más frecuencia en el mantenimiento. Hemos incluido los números de piezas de materiales auxiliares y ayudas de capacitación. Una lista más completa de piezas y accesorios aparece en la Sección de Especificaciones. Piezas de Revisión Cant Nº...
Page 32
SEGURIDAD SEGURIDAD MANIPULACION SEGURA________________________________________________________ ADVERTENCIA EL EQUIPO MANIPULADO INCORRECTAMENTE O POR PERSONAL NO CUALIFICADO PUEDE SER PELIGROSO Familiarícese con la ubicación y correcta utilización de todos los mandos. Todo operador sin experiencia debe recibir instrucciones de alguien que esté familiarizado con el equipo antes de que se le permita manipular la máquina. Nunca desconecte o derive ningún interruptor.
Los ajustes y operaciones de mantenimiento siempre deberán ser realizadas por un técnico cualificado. Si necesita más información, póngase en contacto con su distribuidor Jacobsen quien le informará de los métodos de mantenimiento más recientes y le proporcionará un servicio puntual y eficaz. El uso de piezas y accesorios no autorizados por Jacobsen anulará...
Page 34
ESPECIFICACIONES ESPECIFICACIONES IDENTIFICACION DEL ARTICULO ___________________________________________ 67945 ......LF 3400, 5 Gang 2WD, carrete de 127 mm de diámetro TEXTRON TURF CARE AND SPECIALTY PRODUCTS 67946 ......LF 3400, 5 Gang 4WD, carrete de 127 mm de diámetro RACINE, WI MADE IN U.S.A.
ESPECIFICACIONES MOTOR V1505-TE _________________________________________________________ Marca ......Kubota Reglaje Regulador: Modelo......V1505TE Diesel, 4 ciclos, Ralentí alto....3150 rpm Enfriado por líquido Ralentí bajo....1200 rpm Potencia ......33 kW @ 3000 rpm Lubricación: Capacidad....5,2 litros Desplazamiento....1498 cm Tipo ......SAE 10W30 Par........126 Nm Clasificación API ..
Page 36
Diámetro carrete ...... 178 mm Carrete de 11 cuchillas ..1,65 mm / 1 km/h ACCESORIOS ____________________________________________________________ Consultar el Catálogo de Piezas y ponerse en contacto con su distribuidor Jacobsen para recibir una lista completa de accesorios y herramientas . TRACTOR CARRETES Pistola de aire ...........
Al objeto de evitar posibles lesiones, baje al suelo el tacto con un distribuidor Jacobsen autorizado. grupo de herramientas de corte, desactive todas las Sustituya, y no ajuste, los componentes desgastados y transmisiones, ponga el freno de estacionamiento, pare dañados.
AJUSTES AJUSTE DE LA CUCHILLA FIJA _____________________________________________ Lea la sección 3.2 antes de realizar ningún ajuste. Cuando el carrete esté ajustado correctamente a la cuchilla fija, el carrete girará libremente y se podrá cortar un trozo de papel, por toda la longitud del PRECAUCION carrete con el papel a 90º...
Page 39
AJUSTES FLASH ATTACH ___________________________________________________________ Instalación de las unidades de corte Colocar la unidad de corte frente a su respectivo brazo de elevación. Levantar el brazo de elevación y poner la unidad de corte para que el yugo (T) esté en línea con el bastidor giratorio (S).
AJUSTES PRESION DESCENDENTE __________________________________________________ Cada carrete está equipado con un muelle de presión Medir la longitud del muelle como se indica en los 5 descendente. La presión descendente mejora la calidad de carretes. Anotar la dimensión del muelle más corto y corte mejora la calidad de corte asegurando un contacto ajustar los otros muelles ajustando las barras (U) a constante entre el carrete y el terreno.
AJUSTES FRENOS _________________________________________________________________ Ajustar los frenos después de cambiar o revisar la unidad Arrancar el tractor y revisar la operación de los frenos. de frenos, o si la carrera del pedal es excesiva. Estacionar el tractor en una inclinación (aprox. 16,7º) y poner el freno de estacionamiento.
Page 42
AJUSTES 3.11 VELOCIDAD DE MARCHA HACIA DELANTE / MARCHA ATRAS___________________ Las velocidades de dirección y reversa están ajustadas en LF011 el pedal de tracción. Ajustar la velocidad de dirección antes de ajustar la reversa. Para ajustar la velocidad hacia delante: Comprobar que la bomba de dirección se ha ajustado en neutro y el acelerador del motor está...
Page 43
AJUSTES 3.12 INTERRUPTOR DE LIMITE DE CARRETE DELANTERO___________________________ Los brazos delanteros y derechos de elevación están Arrancar el motor y revisar que los carretes funcionen equipados con interruptores de láminas que indican al al levantarlos. controlador desconectar los carretes. Los interruptores Nota: Los interruptores de láminas ajustan el punto donde están montados en el bastidor del tractor directamente los carretes se desconectan, no la altura a la que suben.
Page 44
Tenga siempre especial cuidado al utilizar valores de par de torsión. Jacobsen utiliza pernos metalizados Grado 5 de serie, a menos que se cite lo contrario. Para tensar pernos metalizados, utilice el valor dado para los lubricados.
Consulte en la sección 6.2 y en el Manual del motor vida útil. los intervalos de mantenimiento específicos. Durante el período de rodaje, Jacobsen recomienda lo Si fuera necesario poner en servicio la bomba de inyección, siguiente : los inyectores o el sistema de combustible, póngase en contacto con un distribuidor Jacobsen autorizado.
MANTENIMIENTO FILTRO DE AIRE __________________________________________________________ Compruebe el indicador de mantenimiento diariamente. Si Vuelva a montar el tapón asegurándose de que se en la ventana (B) aparece la banda roja reemplace el filtro. asiente completamente alrededor del alojamiento del filtro. El evacuador de polvo debe mirar hacia abajo. No extraiga el filtro para inspeccionarlo o limpiarlo.
MANTENIMIENTO BATERIA _________________________________________________________________ Esté absolutamente seguro de que el interruptor de Verifique la polaridad de la batería antes de conectar o encendido esté «apagado» y que se haya retirado la llave desconectar los cables. de contacto antes de poner en servicio la batería. Cuando instale la batería, monte siempre el cable posi- tivo (+) ROJO en primer lugar y el cable negativo (-) PRECAUCION...
MANTENIMIENTO 4.10 ESCAPE Y SILENCIADOR __________________________________________________ Para protegerse del monóxido de carbono, inspeccione todo ADVERTENCIA el sistema de escape regularmente y sustituya siempre el silenciador si está dañado. Los humos de escape contienen monóxido de carbono tóxico y pueden ser fatales sin son inhalados. Si advierte un cambio de color y de sonido del escape, pare el motor inmediatamente.
Page 49
Después de drenar el aceite, instale el inserto de mantenimiento. drenaje y llene el depósito con aceite hidráulico Jacobsen. Drene y reemplace el aceite hidráulico si ha tenido lugar un Purgue el aire del sistema. fallo de componentes grave, si advierte la presencia de...
Page 50
Si el sistema no funciona correctamente y no se puede corregir el problema, póngase en contacto con un distribuidor Jacobsen autorizado. DISYUNTOR DE CIRCUITO Aleje el mazo de cables y todos los cables individuales de las piezas móviles para evitar daños.
Page 51
Distribuidor de Vaciar y rellenar anualmente. Quitar la tapa del radiador, Jacobsen deberá revisar el sistema refrigerante. abrir el tapón de vaciado del bloque del motor y vaciar el radiador. Vaciar y limpiar la botella de recuperación.
Repare las superficies metálicas dañadas y utilice pintura Limpie con aire comprimido el motor y las aletas del para retoques Jacobsen. Aplique una capa de cera al radiador. Puede adquirir nuestra pistola de aire com- equipo para proteger la pintura.
MANTENIMIENTO 4.20 AMOLADO DEL CARRETE __________________________________________________ Importante: Las válvulas de control de velocidad limitan ADVERTENCIA la velocidad en reversa solamente. Una vez ajustada la velocidad de amolado, las válvulas se pueden quedar en Para evitar lesiones graves, mantener las manos, pies y esta posición para el segado normal.
Page 54
MANTENIMIENTO 4.21 ALMACENAMIENTO _______________________________________________________ Generalidades PRECAUCION Lave el tractor a fondo y lubríquelo. Repare y pinte el metal dañado o desnudo. Para evitar que se produzcan lesiones y daños en los bordes de corte, manipule el carrete con sumo cuidado. Inspeccione el tractor, apriete todos los elementos, sustituya los componentes desgastados o dañados.
Page 55
En el siguiente cuadro se enumeran los problemas más comunes que pueden ocurrir durante el arranque y funcionamiento. Para más información detallada acerca de los sistemas hidráulico y eléctrico, póngase en contacto con el distribuidor Jacobsen de su zona . Síntomas Posibles Causas Acción...
Page 56
RESOLUCION DE PROBLEMAS LAMPARAS DEL CONTROLADOR ___________________________________________ El controlador es una unidad sólida que dirige y controla las lámpara. Las salidas son activas cuando se iluminen sus funciones eléctricas. El controlador recibe la señales de luces. entrada desde diversos interruptores y sensores de la Es importante recordar que en algunos casos una lámpara máquina y transmite señales de salida para operar los relés, o grupo de lámparas debe estar iluminado o apagado para...
Page 57
RESOLUCION DE PROBLEMAS CIRCUITOS ELECTRICOS ___________________________________________________ Al tratar de averiguar un problema en la máquina usando el controlador, comprobar siempre que la lámpara de programa activo (1) esté conectada. Esta indica que el controlador tiene potencia y el programa está activo. Nota: El controlador necesita un mínimo de seis voltios para operar.
** O cada dos años, lo que suceda primero. .I Guarnecer cojinetes NLGI Grado 2 (Clase Servicio LB) II Pistola engrase manual NLGI Grado 2 (Clase Servicio LB) III Aceite de motor - ver sección 4.3 IV Aceite hidráulico Jacobsen - SAE 10W30 o Greens Care 68 ES-30...
Page 59
CUADROS DE MANTENIMIENTO Y LUBRICACION CUADRO DE LUBRICACION _________________________________________________ 11 13 Puntos de engrase igual para todos los carretes Accesorios de engrase F1 - 50 horas (Cada Semana) Bastidor Giratorio Brazo Elevación Cilindros Elevación Pivote Brazo Elevación Pivote Pedal Freno Pivote Pedal Tracción Unión Bola Pivote Dirección...
LF 3400 / LF 3800 Serial No. All 1.1 Decals WARNING 1. Read operators manual. Do not allow untrained operators to use machine. 2. Keep shields in place and hardware securely fastened. 3. Before you clean, adjust or repair this equiptment, disengage all drives, engage parking brake and stop engine.
2812267 Decal, Service 3008683 Decal, Backlap Located on Front Axle 365956 Decal, Radiator Warning Located on top of Radiator 4124759 Decal, Jacobsen Emblem 340830 Decal, Spanish Caution 3008521 Decal, Traction Pedal 3008522 Decal, Brake 3001435 Decal, Battery Danger Located on Controller Housing...
LF 3400 / LF 3800 Serial No. All 2.1 Hood 17 22 LF34-1...
Page 65
LF 3400 / LF 3800 Item Part No. Qty. Description Serial Numbers/Notes 4123226 Hood Assembly, LF 3400/3800 Includes Items 13 ~ 16 on Illustration 1.1 4124443 • Foam, Front 4124437 • Foam, Right Side 4124436 • Foam, Left Side 4124442 •...
LF 3400 / LF 3800 Serial No. 67915, 67916-1601 and Up 9.1 4WD Steering Serial No. 67867 -1601 and Up Serial No. 67869-1601 and Up 4WD Units Only Serial No. 67889-1601 and Up LF34-8...
LF 3400 / LF 3800 Serial No. 67915-1601 and Up 16.1 2WD Traction Hydraulics Serial No. 67868-1601 and Up Item Part No. Qty. Description Serial Numbers/Notes 1003462 Hose, Pump to Upper Traction Tee 339994 Adaptor, Straight 339999 Adaptor, Straight 1003463 Hose, Pump to Lower Traction Tee 340339 Tee, Union...
LF 3400 / LF 3800 Serial No. 67916-1601 and Up 17.1 4WD Traction Hydraulics Serial No. 67869-1601 and Up Item Part No. Qty. Description Serial Numbers/Notes 1003440 Hose, Pump To Reverse 4WD Tee 339994 Adapter, Straight 339999 Adapter, Straight 1003457 Tube, Reverse 4WD Tee 1003439 Hose, Pump To Forward 4WD Tee...
LF 3400 / LF 3800 Serial No. All 18.1 Charge Pressure and Steering Hydraulics To Lift Valve P Port Charge To Lift Valve From Gear (Inner) T Port Pump Rear Reel Filter Valve To Steering Cylinder Lift Valve Front Item Part No.
22.1 Front Lift Hydraulics Serial No. All Lift Valve 5 Gang Units Right Front Cylinder Center Front Left Cylinder Front Cylinder Item Part No. Qty. Description Serial Numbers/Notes 1003344 Hose, Lift Valve to Right Front Lift Valve Port 10 1003343 Hose, Right Front to Lift Valve Lift Valve Port 1 1003345...
LF 3400 / LF 3800 Serial No. All 23.1 Rear Lift Hydraulics Item Part No. Qty. Description Serial Numbers/Notes 1003352 Hose, Left Rear to Right Rear Base Ports 1003351 Hose, Left Rear to Right Rear Rod Ports 1003350 Hose, Lift Valve to Inside Tee Lift Valve Port 6 1003349 Hose, Lift Valve to Outside Tee...
LF 3400 / LF 3800 Serial No. All 24.1 Front Reel Hydraulics Item Part No. Qty. Description Serial Numbers/Notes 1003337 Hose, Valve to Right Front Motor Front Reel Valve Port A 1003444 Hose, Right Front to Bulkhead 1003445 Hose, Bulkhead to Center Motor 1003446 Hose, Center Motor to Bulkhead 1003447...
LF 3400 / LF 3800 Serial No. All 25.1 Rear Reel Hydraulics Item Part No. Qty. Description Serial Numbers/Notes 1003336 Hose, Valve to Right Rear Motor 1003443 Hose, Right Rear to Left Rear Motor 1003335 Hose, Left Rear Motor to Valve 1003449 Hose, Left Rear Drain 1003448...
LF 3400 / LF 3800 Serial No. All 27.1 Lift Arms 17 19 23 24 Outside Yokes Only.
Page 105
LF 3400 / LF 3800 Item Part No. Qty. Description Serial Numbers/Notes 4130337 Left Front Lift Arm 4130338 Right Front Lift Arm 4130339 Left Rear Lift Arm 4130340 Right Rear Lift Arm 4130341 Center Lift Arm 3006539 • Bushing 2 Per Lift Arm 1002498 Yoke, Pivot 3008432...
LF 3400 / LF 3800 Serial No. All 28.1 Wire Harness and Controller Box Motor Part of 13 / 30 A - Headlight B - Lift Arm Limit Switch C - Fuel Level Sender/ Instrument Panel D - Seat Switch E - Oil Float Switch F - Glow Plugs G - Fuel Solenoid...
Page 107
LF 3400 / LF 3800 Item Part No. Qty. Description Serial Numbers/Notes 1 ------------ Tray, Battery See 7.1 4122840 Headlight 4123183 • Bulb REFERENCE L-1 and L-2, See 45.1 4122841 Controller REFERENCE U-6, See 45.1 5003282 • Fuse, 20 Amp REFERENCE F-1 &...
LF 3400/ LF 3800 Serial No. All 29.1 Five Inch Reel Assembly LF 3400, LF 3400 Turbo WARNING To prevent cuts use socket wrench or Turf Groomer knob to turn reel. DANGER To prevent injury, disengage all drives, engage parking brake and stop engine before working in machine or emptying grass catchers.
Page 109
LF 3400 / LF 3800 Item Part No. Qty. Description Serial Numbers/Notes 5003087 Frame, Reel 361877 • Decal, Danger 1000997 • Decal, Warning 5003053 7 Blade Left Hand Reel 5003054 7 Blade Right Hand Reel 1004786 Bearing Housing 500534 • Bearing, Cup and Cone 336962 •...
Page 110
LF 3400 / LF 3800 Serial No. All 30.1 Five Inch Reel Assembly LF 3400, LF 3400 Turbo 21/22 26/27...
Page 111
LF 3400 / LF 3800 Item Part No. Qty. Description Serial Numbers/Notes 1000770 Rear Roller See 35.1 1002224 Zerk Bolt 446142 Lockwasher, 3/8 Heavy 400264 Screw, 3/8-16 x 1-1/4” Hex Head 453011 Flat Washer, 3/8 345510 Spacer 2000065 Casting, Counterweight 446130 Lockwasher, 1/4 Heavy 400110...
LF 3400 / LF 3800 Serial No. All 33.1 Down Pressure Spring Item Part No. Qty. Description Serial Numbers/Notes 461397 Roll Pin, 1/4 x 1-1/4” 453017 Flat Washer, 1/2 400268 Screw, 3/8-16 x 1-3/4” Hex Head 3008593 Tube, Down Pressure 460312 Hairpin 443110...
LF 3400 / LF 3800 Serial No. All 34.1 Front Roller Part Number 123268 Item Part No. Qty. Description Serial Numbers/Notes 3003416 Shaft 3000115 Tube ◆ 500534 Bearing, Cup and Cone 471214 Grease Fitting ◆ 338647 Grease Seal ◆ Spacer ◆...
LF 3400 / LF 3800 Serial No. All 38.1 Reel Valve Part Number 2822502 1 / 7 Item Part No. Qty. Description Serial Numbers/Notes 5003080 Flow Control 5003579 • Flow Control Seal Kit 5003032 Solenoid Vlave 339909 • O-Ring REFERENCE K-3 and K-4, See 45.1 5003033 Coil REFERENCE K-7 and K-8, See 45.1...
LF 3400 / LF 3800 Serial No. All 39.1 Front Wheel Motor Part Number 1001757 ◆ Included In Seal Kit 557651 ❍ Included In Seal Kit 5002111 Item Part No. Qty. Description Serial Numbers/Notes 558066 Screw, Torx 5002110 Front Retainer 558063 Shaft and Bearing Kit 557624...
LF 3400 / LF 3800 Serial No. All 40.1 Rear Wheel Motor Part Number 390859 Item Part No. Qty. Description Serial Numbers/Notes Seal Exclusion Seal, 3” I.D. Back Up Ring Shaft Seal 554781 Shaft and Bearing Kit 554780 554779 Hex Nut Shaft Face Seal Inner Face Seal Outer Face Seal...
LF 3400 / LF 3800 Serial No. All 41.1 Lift Valve Part Number 2822501 Front Rear Used with LF 3400 and 3400 Turbo Models. Item Part No. Qty. Description Serial Numbers/Notes 5003144 Relief Valve 5003579 • Relief Valve Seal Kit 5001355 Pilot Operated Check Valve 5003578...
LF 3400 / LF 3800 Serial No. 42.1 4WD Valve Part Number 2822500 Top View Front View Item Part No. Qty. Description Serial Numbers/Notes 5003507 Coil REFERENCE K-1 and K-2, See 45.1 5003096 Solenoid Valve 5003578 • Solenoid Valve Seal Kit 5003121 Solenoid Valve 5003554...
LF 3400 / LF 3800 Serial No. All 42.1 Reel Motor Part Number 2822503 (Five Inch Reel) Item Part No. Qty. Description Serial Numbers/Notes 5001068 O-Ring 5003140 Relief Valve 5003688 Face Plate 5003589 Seal Kit > Change from previous revision...
Page 127
LF 3400 / LF 3800 Serial No. All 43.1 Reel Motor Part Number 1002620 (Seven Inch Reel) Used on LF 3800 Models. Item Part No. Qty. Description Serial Numbers/Notes 3006021 O-Ring 5003140 Relief Valve 5003485 Face Plate 5003031 Seal Kit Not Shown 4102440 Shaft, Output...
LF 3400 / LF 3800 Serial No. All 44.1 Steering Valve Part Number 1003458...
Page 129
LF 3400 / LF 3800 Item Part No. Qty. Description Serial Numbers/Notes 443108 Locknut, 5/16-18 Center Port Cover Seal, O-Ring Seal, O-RIng Seal, O-RIng 443828 Nut, 5/8-18 Hex Jam Special Bolt Port Manifold Spring, Port Side Hex Drive A and E Needle Roller 503398 Valve Ring...
LF 3400 / 3800 Serial No. All 45.1 Electrical Schematic A B C D E F G H J K L M N Og/Wh Og/Wh LB/Tn Og/Wh Og/Wh SW-13 LB/Tn LB/Tn SW-3 Og/Wh SW-6 Lb/Bk K-10 Og/Bu Lb/Bk K-11 Bn/Ye Og/Bu Pu/Wh RD B...
Page 131
LF 3400 / 3800 Pk/Bk Og/Wh Og/Bk Og/Wh Gauges Switches Grd-1 Battery A B C D E F G H J K L M N...
Page 132
LF 3400 / 3800 Reference Part Item Description Serial Numbers/Notes Illustration Number See 28.1 366931 Battery CB-1 See 28.1 361439 50 Amp Circuit Breaker (Alternator) See 28.1 5003282 20 Amp Fuse (Ignition Circuit) Included in Controller See 28.1 5003282 20 Amp Fuse (Lights) Included in Controller See 42.1 5003507...
Page 133
LF 3400 / 3800 Reference Part Item Description Serial Numbers/Notes Illustration Number SW-16 See 27.1 4125831 Left Reel Level Proximity Switch See 4.1 3005121 Temperature Gauge See 4.1 365943 Fuel Gauge See 4.1 4129683 Hour Meter See 4.1 366670 Horn Not Shown Cruise Control Module (Option) See 28.1...
LF 3400 / LF 3800 Serial No. All 46.1 Hydraulic Schematic 5 Gang Units (LF 3400, LF 3800 and LF 3400 Turbo) Reverse Diag. Valve 3625 psi 2.81 ci Gear 3000 .5 ci .5 ci .5 ci Pump 3625 psi Traction Pump Drain...
Page 135
LF 4675 / LF 4677 Front 4WD Valve Wheel Rear Motors 19.0 ci 19.0 ci Wheel Motors 8.0 ci 8.0 ci 450 psi 10 Micron 25 psi 25 psi Charge Filter .040 Right .026 Right One Way Front .040 Rear Left Cylinder Cylinder...
LF 3400/ LF 3800 Serial No. All 47.1 O-Ring Chart O-Ring Face O-Ring Boss O-Ring Face O-Ring Face O-Ring Boss O-Ring Boss Seal Size Dash Size Seal Size Seal Size Dash Size Dash Size W-X-Y W-X-Y W-X-Y O-Ring Face O-Ring Not O-Ring Face O-Ring Boss O-Ring Face...
Fluids and Compounds Hydraulic Fluid* 5001405 Two 2-1/2 Gallon Container of ISO VG68 Oil 5001404 One 5 Gallon Pail of ISO VG68 Oil 2500548 Two 2-1/2 Gallon Container of 10W30 Oil 2500546 One 5 Gallon Pail of 10W30 Oil 503409 Two 2-1/2 Gallon Container of ATF Fluid 503407 One 5 Gallon Pail of ATF Fluid...
Page 144
Equipment from Jacobsen is built to exacting standards ensured by ISO 9001 and ISO 14001 registration at all of our manufacturing locations. A worldwide dealer network and factory trained technicians backed by Textron Parts Xpress provide reliable, high-quality product support.