Table of Contents
Advertisement
HIGH ALTITUDE OPERATION
In Canada, this unit is approved from 0 to 4500 feet above
sea level. Installation of this stove at altitudes above 4500
feet is subject to field test of the individual installation and
approval by the local authority having jurisdiction.
In the United States, input ratings of this unit are based
on sea level operation, and shall not be changed for operation
at elevations up to 2000 feet. For operation at elevations
above 2000 feet, this stove shall be reduced at the rate of
4% for each 1000 feet above sea level.
Exception: As permitted by the authority having jurisdiction.
To adjust stove for operation above 2000 feet the burner
orifices may need to be changed. The orifices are located
beneath the log set so it is necessary to first remove the logs.
To do so please refer to the following detailed instructions to
achieve optimum performance of your stove.
WARNING ! The following procedure should only be
undertaken by a qualified and certified gas appliance
installer.
CAUTION: DISCONNECT ANY ELECTRICAL CORDS AND
TURN OFF GAS SUPPLY TO UNIT BEFORE PROCEED-
ING.
1.
If logset is installed, remove logs, lava rock and
embers.
2.
With a Phillips screwdriver, remove seven screws (3 in
front and 2 on each side), and lift out burner tray.
3.
Remove the two Phillips head screws that secure the
burner pan in place.
4.
Remove the burner pan by sliding to the right and
lifting out. (Shutters may need to be adjusted 'closed'
to make this easier).
5.
Slide shutters out of the way. Using a 5/8" wrench
or socket, remove the orifice and replace with proper
orifice for the specified gas. See below.
6.
Reinstall burner pans and adjust shutters to 'open'
position.
CAUTION: The correct orifice placement is critical for
proper appliance performance follow BTU
de-rating chart below to locate the necessary
orifice size for the front and rear burners.
Page 36
QFP 30 Direct Vent Gas Fireplace
equivalent orifice sizes at high altitudes
(Includes 4% Input Reduction For Each 1000 Feet)
Orifice size
2000 3000 4000 5000 6000 7000 8000 9000 10000
at Sea Level:
Natural Gas
Front
36
36
36
Propane
Front
52
52
52
Read this entire manual prior to using the fireplace. Pay
particular attention to the "Safety Precautions" section on
pages 6-9. Failure to follow the instructions may result in
property damage, bodily injury, or even death.
MAIN BURNER .................. This control is used to turn the
fireplace on and off.
PILOT IGNITOR ................ The pilot ignitor is used only to
start the pilot. When pressed, it sends an electrical charge to
the pilot assembly. This creates a blue spark directly next to
the pilot, igniting the pilot flame.
VALVE CONTROL ............. This knob is used to control gas
to the fireplace and for starting the pilot. There are three
positions, ON, OFF, & PILOT. The pointer on the panel
indicates the position of the knob.
COMFORT CONTROL....... This knob controls the flame height
from low ("LO") to high ("HI").
FAN SPEED ....................... This knob controls the speed of
the internal convection blower that pushes the heated air
into the room.
NOTE: If using a remote control or thermostat, the On/Off
Switch must be left "OFF". Turning the On/Off Switch "ON"
will keep the fireplace on continually.
IGNITOR
MAIN
BURNER
37
38
39
40
40
52
53
53
53
54
OPERATION
THERMOSTAT
FAN
CONECTION
SPEED
COMFORT
CONTROL
41
41
54
54
03/21/01 #250-6120
VALVE
CONTROL
Hide quick links:
Advertisement
Table of Contents
