Other Functions; Checking Tape Position; Changing Display Information - JVC HR-J695U Instructions Manual

Other Functions

Checking tape position

When you change the VCR operation
mode from the stop mode to fast forward
or rewind mode, or when you perform an
Index Search or Instant Review, the tape
position indicator appears.
The position of " " in relation to "B"
q
(Beginning) or "E" (End) shows you where
you are on the tape.
● Set "SUPERIMPOSE" to "ON".

Changing display information

Each time you press DISPLAY, the display panel
shows the channel number and the clock time
alternatively.
● You can change display in the stop, recording or
recording pause mode, or during rewind/fast-
forward.
● When "SUPERIMPOSE" is set to "ON" and DISPLAY on the
Remote is pressed, time counter will appear on the TV screen.
To reset the time counter, press C. RESET on the Remote.
Timer warning display
A warning appears on the TV screen to tell
you that the timer-recording is to start in
5 minutes if you are not in the timer
recording standby mode at that time. Press
TIMER to put the VCR into timer recording
standby mode. To clear the display, press
CANCEL on the Remote.
Function settings
You can use the other useful function settings on the Function Set
screen.
A
Access Main Menu screen, then
Function Set screen
Press MENU on the Remote. Press
move the highlight bar (arrow) to
"FUNCTION SET", then press OK or
B
Select Function
Press to move the highlight bar (arrow) to the function you
rt
want to set.
FUNCTION
PICTURE CONTROL NORM
AUTO TIMER OFF
SUPERIMPOSE ON
AUTO SP EP TIMER OFF
VIDEO STABILIZER OFF
BLUE BACK ON
NEXT PAGE
SELECT WITH ( , ) AND (OK)
PRESS (MENU) TO END
C
Change setting
Press OK or . The default setting is bold in the following table.
e
Press MENU to return to normal screen.
After a power failure occurs, Function Settings will be reset to
its default setting.
+ +
B
COUNT
–WARNING–
TIMER RECORDING
TO START SOON
(CANCEL)
MAIN MENU
FUNCTION SET
TUNER SET
INITIAL SET
to
rt
.
e
PRESS ( , ), THEN (OK)
PRESS (MENU) TO END
PREVIOUS PAGE
2ND AUDIO RECORD OFF
AUDIO MONITOR HI-FI
SELECT WITH ( , ) AND (OK)
PRESS (MENU) TO END
PICTURE CONTROL — NORM/EDIT/SOFT/SHARP
This function helps you to adjust the playback picture quality
according to your preference.
NORM: Normally select this. Original picture appears and the VCR
does not perform any picture adjustments.
EDIT: Minimizes picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing much noise.
SHARP: Clearer, sharper-edged picture when viewing images with
much flat, same-colored surfaces such as cartoons.
+ E
NOTE:
1:23:45
Select "EDIT" when you are editing tapes. After you finish editing
the tapes, select back to the mode of your choice.
AUTO TIMER — ON/OFF
● When this function is set to "ON":
The timer recording standby mode is automatically engaged when
the VCR is turned off. It is temporarily canceled when the VCR is
turned on. You do not have to press TIMER to engage or disengage
the timer recording standby mode.
● When this function is set to "OFF":
You have to press TIMER to engage or disengage the timer
recording standby mode.
SUPERIMPOSE — ON/OFF
When this function is set to "ON", various VCR status information
(on-screen display) appears on the screen.
NOTE:
When you use this VCR as the playback VCR for editing a tape, be
sure to set this function to "OFF"; otherwise, the VCR status
information (on-screen display) will be recorded on the edited
tape.
AUTO SP]EP TIMER — ON/OFF
When this function is set to "ON", the VCR automatically
switches to EP mode to allow complete recording if there is not
enough tape to record the entire program while timer-recording in
SP mode.
For Example, Recording a program of 140 minutes in length onto
a 120-minute tape
Approximately 110 minutes
SP mode
NOTES:
● If you have programed the VCR to timer-record 2 or more
programs, do not use this function, but change the tape speed
manually during timer programing.
● There may be some noise and sound disturbance where the tape
speed switches from SP to EP mode on the tape.
● This function is not available during ITR (Instant Timer
Recording), and will not work properly on the following tapes:
T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
VIDEO STABILIZER — ON/OFF
When this function is set to "ON", you can automatically correct
vertical vibrations in the picture when playing back unstable
recordings made on another VCR.
NOTE:
To watch recordings with close-caption or when you finish
viewing a tape, set this function to "OFF".
BLUE BACK — ON/OFF
When this function is set to "ON", the TV screen becomes all blue
in the following cases:
● When receiving a channel not in use.
● When stopping playback.
NOTE:
When you want to receive an unstable channel with poor signals,
set this function to "OFF".
Approximately 30 minutes
EP mode