V/H - Selecting Vertical/Horizontal Polarisation And Input A/B; Video - Adjusting The Video Deviation; Audio - Mono/Stereo And Sound Carrier Switching; Down/Up Setting Buttons - Grundig STR 400 AP Instruction Manual

Buttons and their Functions on the Receiver
Examples:
IF 1: Entry:
1200 MHz 01200
950 MHz 00950
Please also observe setting of the video deviation –1, –2 or
–3 (see paragraphe " ¢ Video – Adjusting the Video Deviation").
¢ ¢
V/H – Selecting Vertical/Horizontal
Polarization and Input A/B
Press the ¢ V/H button to indicate the current polarization in
the display, e.g., (H1 18 V)
I99 H1X18VX-
< / > buttons, you can select between V1, H1,
¢
With the
V2, and H 2.
Allocation of the respective LNC voltage depends on the
selected LNC system (see paragraphe "Setting Zero Position
and Limits").
For LNC´s with magnetic polarizer, the optimum skew value
must be adjusted after having selected the polarization (see
also paragraphe "SKEW ALL – Transferring the Skew Value").
¢
Press the V/H button once again to indicate on the display
the input which is to be selected with the
(" INPUT A " or " INPUT B "). See also the sections "Adap-
ting the Polarizer, Installation Menu", and "Selecting the Aerial
Input".
¢ VIDEO – Adjusting the Video Deviation
The frequency-modulated satellite signals are transmitted
with different deviations. To obtain a good picture, the recei-
ver must be adjusted correspondingly.
Press the ¢ VIDEO button to indicate on the display the
video deviation and video polarity, e.g., (DEV. 3).
I99 DEV
.
X3XX
The video deviation is selected with the
DEV. 1 = 25 MHz,
DEV. 2 = 22.5 MHz,
DEV. 3 = 16 MHz,
For C-band and S-band reception with 4- resp. 2.5GHz
LNC´s, the video signal must be inverted by selecting the set-
ting DEV. –1 ... DEV. –3.
Indication:
11200 Mz
10950 Mz
o p ü +
TIMER
STEREO
SIGNAL IIIIIIIIIIIII
< / > buttons
¢
o p ü +
TIMER
STEREO
SIGNAL IIIIIIIIIIIII
< / > buttons:
¢
DEV. –1 = 25 MHz,
DEV. –2 = 22.5 MHz,
DEV. –3 = 16 MHz.
¢ ¢
AUDIO – Mono/Stereo and Sound
Carrier Switching
¢
Press the AUDIO button to indicate the current audio
mode in the display, for example:
I99
MONOX
By repeatedly pressing the
between:
MONO < > = Main carrier, Mono wide,
MONO > < = Subcarrier, Mono Panda Wegener,
STEREO = Panda carrier*, Stereo.
On STEREO, the indication "STEREO" appears in addition on
´`
the display of the receiver. Press the
ton to indicate the actual value of the set frequency, for exam-
ple:
I99 X7
.
You can adjust the frequency between 5.00 MHz and
9.99 MHz in steps of 10 k Hz.
Pressing and holding down the
scan the frequencies at high speed.
Direct frequency entry is possible with the numeric buttons of
the remote control handset. Tuning will be effected only after
having entered the third frequency digit.
¢
< / >

– Down/Up Setting Buttons

When in programme mode, use the
the next programme position down or up.
In the other modes, the
ging the entered data.
When holding down the corresponding button, the program-
me positions or data values are selected and displayed at
high speed.
When in standby, pressing the
the last selected SAT programme position (Last Station
Memory).
¢
MEMORY – Storing Data in Memory
Pressing the ¢ MEMORY button stores all data in memory.
*
Panda/Wegener Communications Inc.. Award for highest tone quality.
18
o p ü +
TIMER
< >
X
STEREO
SIGNAL IIIIIIIIIIIII
¢ AUDIO button, you can select
< or
¢ ¢
o p ü +
TIMER
z
02MH
STEREO
SIGNAL IIIIIIIIIIIII
< or > button will
¢ ¢
< / > buttons to select
¢
< / > buttons are used for chan-
¢
< / > buttons will switch to
¢
> but-