1. Manuals
  2. Brands
  3. Miele Manuals
  4. Dishwasher
  5. G 818
  6. Installation instructions manual

Miele G 603 Installation Instructions Manual

45 cm wide fully integrated dishwashers
Hide thumbs Also See for G 603:
Table of Contents

Advertisement

Quick Links

Installation instructions

for 45 cm wide fully integrated
dishwashers
G
It is essential to read the operating and
installation instructions before
installing or using the machine,
to avoid the risk of accident or
damage to the machine.
M.-Nr. 05 585 941

Advertisement

Table of Contents
loading

Related Manuals for Miele G 603

Summary of Contents for Miele G 603

  • Page 1: Installation Instructions

    Installation instructions for 45 cm wide fully integrated dishwashers It is essential to read the operating and installation instructions before installing or using the machine, to avoid the risk of accident or damage to the machine. M.-Nr. 05 585 941...
  • Page 2 The data plate is located on the right hand side of the door when open. The model numbers quoted refer only to the basic model number, e.g. the G 603 SC-Vi is described as the G 603. It is essential to read the "Warning and Safety Instructions" in the Operating...

  • Page 3: Table Of Contents

    Contents Installation ............4 Opening the door.

  • Page 4: Installation

    Installation Opening the door This dishwasher is specially designed for integration under a worktop run in a fitted kitchen. – The front of the dishwasher is designed to take a front panel. It can be fitted with a base unit door front to match the rest of the kitchen.
  • Page 5 Installation Building in dimensions Dishwasher models G 803 - G 818 Dishwasher models G 603 - G 618 1) Machine height 890 mm 2) Machine height 840 mm 1) Machine height 870 mm Adjustment range approx. 5 cm 2) Machine height 820 mm (84 - 89 cm total height).

  • Page 6: Fitting Protective Cover Plate To Worktop

    Installation 1. Fitting protective cover plate Wood or laminate worktops: to worktop The underside of the worktop is protected against steam rising from the The plexiglass relfector panel and all machine by a special cover plate. other installation items required are A plastic holder is located on the left included in the accessories pack hand side of the cover plate for the...
  • Page 7 Installation ^ Align the cover plate to the front ^ Press the reflector panel into the edge of the worktop in the middle of plastic holder in the cover plate. the niche. If the worktop has a very rounded edge, pull the cover plate further forward so that the reflector panel is still visible later on.
  • Page 8 Installation ^ Stick the doublesided adhesive strip Granite or marble worktops: supplied onto the back of the plastic Worktops made from hard materials holder. such as granite or marble do not need ^ Remove the protective foil from the the cover plate for protection. The cover plate is only used as a guide for adhesive strip and stick the holder to marking the position for the reflector...

  • Page 9: Building The Dishwasher Into A Niche

    Installation 2. Building the dishwasher Dishwasher height into a niche ^ Adjust the height manually before installing the dishwasher. Connection to water and drainage Leave a space of approx. 5 mm should be sited beside and not behind below the worktop to allow the the dishwasher for accessibility.

  • Page 10: Securing Pieces

    Installation Securing pieces To ensure stability, the dishwasher must be fixed securely to the neighbouring units (step 5). Two securing pieces are supplied for this purpose. ^ Push the dishwasher right back into the recess. Ensure that the drain hose, inlet hose and the electric cable are laid to reach the connection point without any kinks.
  • Page 11 Installation Rear screw feet Front screw feet ^ Use a TORX T20 screwdriver to ^ Adjust the front screw feet manually adjust the rear screw feet to the or with a flat blade screwdriver. required height. Now adjust the feet until the seal on Higher = turn clockwise the top of the dishwasher is right up Lower = turn anti-clockwise...

  • Page 12: Fitting The Matching Door Front

    Installation 3. Fitting the matching door The weight of the door front will front affect the functioning of the door The front of the dishwasher needs to be springs. After fitting it is essential for fitted with a base unit front to match the this to be checked out.
  • Page 13 Installation Dimension X must be calculated and Fitting the fixing bracket to a door noted before attaching the fixing front bracket. ^ Lay the door front down with the rear Dimension X is the distance shown on side facing upwards. Draw a vertical the illustration between the drill hole in line down the middle of the door front the machine outer door panel and the...
  • Page 14 Installation ^ If necessary pre-drill holes for the There are notches on the fixing bracket, marked a in the illustration. screws (Ø 2.5 mm, approx. 10 mm deep). ^ Lay the fixing bracket on the rear of ^ Screw the fixing bracket on securely. the door front, using dimension X for the distance from the bottom, and so Only one screw is required in each of...
  • Page 15 Installation Fitting the door front ^ Hang the door front so that the lower lugs of the fixing bracket fit into the The door front is correctly fitted when: lower slits of the dishwasher outer door panel, and draw slightly –...

  • Page 16: Adjusting The Door Front

    Installation 4. Adjusting the door front ^ Close the dishwasher door. ^ Check the alignment of the door When fitted the door front can be adjusted up to a maximum of 2 mm panel again. upwards or downwards to match ^ If it is not correctly aligned you may adjoining unit fronts.

  • Page 17: Securing The Dishwasher

    Installation 5. Securing the dishwasher To ensure stability, the dishwasher must be fixed securely to neighbouring units using the fixing brackets. ^ Open the dishwasher door. ^ Screw the countersunk screws (3.5 x 15) supplied through the fixing brackets on the left and right hand sides into the neighbouring units to secure the dishwasher.

  • Page 18: Adjusting The Door Springs

    If the the door front is too heavy for the door springs (i.e. the door falls open) then stronger springs should be fitted. Please contact your Miele dealer or the Miele Spare Parts Department for ^ Adjust the door spring with a Torx advice.

  • Page 19: Matching The Plinth Facia Of A Kitchen Run

    Installation 7. Matching the plinth facia of a ^ Place the plinth facia directly in front of the kitchen run but do not attach. kitchen run ^ Carefully open the dishwasher door. The plinth area of the dishwasher is normally covered with a plinth run If the door front comes into contact with matching the kitchen furniture.

  • Page 20: Electrical Connection

    All electrical work should be carried complete connection box and cable out only by a suitably qualified and by a Miele approved service competent person, in strict technician only. accordance with national and local safety regulations.
  • Page 21 Electrical connection The wires in the mains lead are coloured in accordance with the following code: Green/yellow = earth Blue = neutral Brown = live If the colours of the wires in the mains lead of this appliance do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows:...

  • Page 22: Plumbing

    (see illustration). withstand pressure of 140 bar may be bought from the Miele Spare Parts Dept. – A stopcock with a 3/4 " male thread must be provided on site.

  • Page 23: Drainage

    Plumbing Drainage Venting the drainage system ^ Open the dishwasher door fully. – The machine drainage system is fitted with a non-return valve, which If the site drain connection is situated prevents dirty water from flowing lower than the guide path for the back into the machine via the drain bottom basket rollers in the open door hose.

  • Page 24: Special Accessories

    ... adjust the height of the dishwasher to ...kit with extended machine feet between 87 cm and 92 cm (G 603 - G 618) or between 89 cm and 94 cm (G 803 - G 818)

  • Page 25: Technical Data

    Technical data Dishwasher model G 603 G 803 Height 81.7 cm 84.7 cm (adjustable + 5.0 cm) (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm) Width 44.8 cm 44.8 cm...
  • Page 26 Technical data Dishwasher model G 618 G 818 Height 81.7 cm 83.7 cm (adjustable + 5.0 cm) (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm) Width 44.8 cm 44.8 cm Width of building in recess 45 cm 45 cm...
  • Page 28 Alteration rights reserved (NovoPlus Vi45) / 2006 M.-Nr. 05 585 941 / 01 en - GB...

This manual is also suitable for:

G 603 sc-vi

Table of Contents