Tv Operation; Starting Setup - JVC LT-32DM21 Owner's Manual

Starting setup

The Starting Setup menu appears the first time
you turn on the TV, and assists you to specify the
Air/Cable setting, and program your channels
automatically.
IMPORTANT: Make sure that the antenna or cable
TV system connection is made!
1
To turn on the TV, press POWER (POWER indicator
on the front of the unit changes green. It may take
approx. 10 seconds for a picture to appear on
screen.). The starting setup function begins.
Auto Setup
TV Location Store
Signal Type Cable
Automatic Search Start
This unit has been preset to STORE brightness
This setting does not qualify under ENERGY
STAR V4.0. To reduce brightness and energy
consumption, change setting to 'HOME'. This
setting does qualify under ENERGY STAR V4.0.
: Select : Adjust
2
Press ▲/▼ to select "TV Location", then press
◀/▶ to select "Store" or "Home". This product
qualifies for ENERGY STAR 4.0 In Home mode
default setting.
NOTE:
• This unit has been preset to STORE brightness.
This setting does not qualify under ENERGY
STAR V4.0. To reduce brightness and energy
consumption, change setting to 'HOME'. This
setting does qualify under ENERGY STAR V4.0.
• The device may not conform to the ENERGY
STAR 4.0 standard after Reset is performed or
the Backlight is adjusted.
3
Press ▲ or ▼ to select "Signal Type", then press
◀ or ▶ to select "Cable" or "Air".
4
Press ▲ or ▼ to select "Automatic Search", then
press ▶ or ENTER.
5
Now the "Auto Setup" starts. After the starting
setup is completed, the TV channel appears on
the screen.
•
Depending on the reception condition, it may
take from 15 minutes to 30 minutes to complete
memorizing digital cable channels. Please be patient.
NOTE:
• If you press ENTER in the process of "Auto Setup",
the Starting Setup stops and changes to the normal
screen.
• When you make a menu selection, your changes
occur immediately. You do not have to press EXIT/
CANCEL to see your changes.

TV operation

1
To turn on the TV, press POWER.
(POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.)
2
Adjust the volume level by pressing VOL + or – .
The volume level will be indicated on the screen
by blue bars. As the volume level increases, so do
the number of bars. If the volume decreases, the
number of blue bars also decreases.
3
Set the Signal Type option to the appropriate
position (see "Air/Cable selection" on page 21).
18
4
Press the Direct Channel Selection (0-9, –)
buttons to select the channel.
(If you press only channel number, channel
selection will be delayed for a few seconds.)
TO SELECT ANALOG CHANNELS
1-9: Press 1-9 as needed. Example, to
select channel 2, press 2, then press
ENTER.
10-99: Press the 2 digits in order. Example,
to select channel 12, press 1, 2, then
press ENTER.
100-135: Press the 3 digits in order. Example, to
select channel 120, press 1, 2, 0, then
press ENTER.
TO SELECT DIGITAL CHANNELS
Press the first 1-3 digits, then press the – button,
followed by the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1,
then press ENTER.
• If a channel is selected with only audio content,
"Audio only" will be displayed on the screen.
• If a channel is selected with a weak digital signal,
"Digital channel signal strength is low" will be
displayed on the screen.
The same program may be available on either an
analog channel or a digital channel. You may choose
to watch either format.
• If a channel is selected to which you have not
subscribed, "Digital channel is encrypted" will be
displayed on the screen.
VHF/UHF/CABLE CHANNELS
Air
VHF
2-13
UHF
14-69
NOTE:
• If a channel with no broadcast is selected, the
sound will automatically be muted.
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.
To select the video input source
To view a signal from another device connected to
your LCD TV, such as a VCR player, press INPUT
SELECT, then press ▲/▼ or corresponding Number
buttons (0-7), then press ENTER. You can select
TV, Video1, Video2, Component, HDMI1, HDMI2, PC
or DVD depending on which input jacks you used to
connect your devices.
Input Select
0.TV
1.Video1
2.Video2
3.Component
4.HDMI1
5.HDMI2
6.PC
7.DVD
[0-7]:Select
CH /
Press and release CH / . The channel automatically
stops at the next channel set into memory.
For proper operation, before selecting channels, they
should be set into the memory. See "Memorizing
channels" on page 21.
Cable
VHF
2-13
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-135 (100) (135)
01 (4A)