Operation In Automatic Mode; Operation In Timer Mode - Rinnai RD-400AU Operation & Installation Manual

OPERATION IN AUTOMATIC MODE

1. Open the dryer door and place items selected for drying evenly into the dryer drum. Close the
dryer door and press the 'On/Off' button
+ EXTRA SOFT
7
2. To select an alternative drying programme press the 'Programme' button
mode indicator illuminates. The drying programmes cycle through the following sequence:
GENERAL + EXTRA SOFT
3. Press the 'Start / Pause' button
green, and will change to red after burner ignition which may take up to 10 seconds.
4. Drying will now commence. The approximate remaining drying time will be indicated on the digital
display . The 'OPERATING' (Combustion) indicator
15
and red, however this is normal.
5. The dryer will stop when items are sufficiently dry. A tone will sound 3 times and the 'FINISH'
indicator will illuminate.
12
Before opening the dryer door, ensure the 'OPERATING' (Combustion) indicator
shows green.
11
NOTE
If the dryer door is opened and closed during operation the dryer will go through a
cool down, purge and relight sequence that takes approximately 1 to 2 minutes.

OPERATION IN TIMER MODE

1. Open the dryer door and place items selected for drying evenly into the dryer drum. Close the
dryer door and press the 'On/Off' button
2. Press the 'Timer' button
programme is GENERAL
3. There are only two drying programmes available in "Timer' mode, these are
GENERAL and DELICATE
7
desired programme mode indicator illuminates.
4. The default drying time in minutes is shown on the digital display
pressing the 'up'
5,10,15,20,25,30,40,50,60,70* and 80* minutes (*Dry-Soft 6 model only).
The 'default' drying time is 20 minutes when the appliance is first connected to the
electric power supply. If the appliance has operated in timer mode previously the
NOTE
previous drying time selected will be shown as the default drying time.
5. Press the 'Start / Pause' button
'Timer' operation has begun. The 'Operating / Combustion' indicator
change to red after burner ignition which may take up to 10 seconds.
6. Drying will now commence. The approximate remaining drying time will be indicated on the digital
display and will counted down in 5 minute increments. During operation the time may be
15
increased and decreased as desired by pressing the 'up'
'OPERATING' (Combustion) indicator
is normal.
7. The dryer will stop when the drying time has elapsed. A tone will sound 3 times, the 'TIMER'
indicator will stop flashing and the 'FINISH' indicator
13
Before opening the dryer door, ensure the 'OPERATING' (Combustion) indicator
shows green.
11
NOTE
If the dryer door is opened and closed during operation the dryer will go through a
cool down, purge and relight sequence that takes approximately 1 to 2 minutes.
Rinnai
OPERATION
1
and these mode indicators will be illuminated.
9
GENERAL
. The 'OPERATING' (Combustion) indicator
2
1
, the 'TIMER' indicator
4
and this mode indicator will be illuminated.
7
, press the 'Timer' button
10
or 'down' buttons. The drying times that can be selected are
5 6
, the 'TIMER' indicator
2
will show green towards the end of the drying cycle, this
11
. The default drying programme is set to GENERAL
THICK+ EXTRA SOFT
may alternate between showing green
11
.
illuminates and the default drying
13
until the
4
15
will begin to flash to signify that a
13
5
will be illuminated.
12
6 Dry-Soft® RD-400/600AU Operation Manual
until the desired
3
THICK DELICATE
will show
11
GENERAL
DELICATE
. Change the drying time by
will show green and will
9
or 'down' buttons. The
6