Network Setting - Panasonic TC-P54Z1 Operating Instructions Manual

Network Setting

This is a setting for connecting to a broadband environment.
Display menu
Select "Setup"
Menu
Picture
Audio
Timer
Lock
VIERA Link
SD card
Closed caption
Setup
Select "Network setting"
Setup
VIERA Link settings
Network setting
VIERA CAST setting
Network Cameras list
ECO/energy saving
Advanced setup
About
Reset to defaults
■
Press to exit from
a menu screen
Select the item and adjust
Network setting
■
Connection test
Press to return
IP setting mode
IP address
to the previous
Subnet mask
screen
Default gateway
DNS setting mode
Primary DNS
Secondary DNS
Network setting
LAN speed setting
LAN speed
Software update
MAC address
50
Connection
test
select
set or next
IP setting
• IP setting
mode
• IP address
• Subnet mask
• Default
gateway
select
2/2
DNS setting
• DNS setting
mode
• Primary DNS
• Secondary
DNS
select
1/2
Succeeded
adjust
Automatic
---.---.---.---
---.---.---.---
---.---.---.---
Automatic OK Connection
---.---.---.---
speed
---.---.---.---
setting
2/2
Automatic
• LAN speed
- - -
setting
12-34-56-78-80-ab
• LAN speed
Software
update
Check that the network settings are as shown below, and then start "Connection test".
Select "Connection test" and press OK.
*Press OK again to cancel the test.
(It takes a while to cancel the test.)
select
Network setting 1/2
Connection test Succeeded
IP setting mode Manual
ok
IP address 192.168.0.5
Subnet mask 255.255.255.0
Default gateway 192.168.0.254
Select "IP setting mode" and set to "Automatic".
(When IP automatic acquisition in DHCP can be used)
Network setting 1/2
select
Connection test Succeeded
IP setting mode Automatic
IP address ---.---.---.---
ok
Subnet mask ---.---.---.---
Default gateway ---.---.---.---
The acquired address is displayed.
Each IP address is acquired automatically.
Select "DNS setting mode" and set to "Automatic".
(When DNS automatic acquisition in DHCP can be used)
select
Network setting 1/2
Connection test Succeeded
Default gateway 192.168.0.254
IP setting mode Automatic
DNS setting mode Automatic OK
ok
Primary DNS ---.---.---.---
Secondary DNS ---.---.---.---
The acquired address is displayed.
Each IP address is acquired automatically.
If you are using a broadband router, IP automatic
acquisition in DHCP can be used under normal
circumstances. If you are not sure, check with the
person who installed the equipment, or check the
instructions for each device.
Select "LAN speed setting" (Default is "Automatic")
select
Network setting 2/2
LAN speed setting Automatic
LAN speed - - -
Software update adjust
MAC address 12-34-56-78-80-ab
Select "Software update"
select
Network setting 2/2
LAN speed setting Automatic OK
LAN speed - - -
Software update ok
MAC address 12-34-56-78-80-ab
The network settings become effective when you close the menu and run "Connection test".
Succeeded: "Connection test" succeeded
Only home network:
Home network is available.
Failed: Check the broadband environment connection
and settings and the network settings, and then
perform the test again.
Test in progress
---: Test not yet performed
■
Manual setting
Select "IP setting mode" and set to "Manual"
Select the item and press OK
Check the specifications of the broadband router and
enter each IP address.
Subnet mask 10I 0 . 0 . OK 0 . 0
change
or
channel
ok
■
Manual setting
Select "DNS setting mode" and set to "Manual"
Select the item and press OK
Enter each IP address as was specified by the
provider.
Primary DNS 10I 0 . 0 . 0 . 0
select
or
ok
Normally, select "Automatic".
If "Connection test" failed, set the "LAN speed setting"
to "manual" and then select "10BASE half duplex",
"10BASE duplex", "100BASE half duplex" or "100 BASE
duplex".
Cannot be selected when the "LAN speed setting" is
"Automatic".
Changing the settings may make it impossible to
connect some types of equipment.
Press OK to start the software update screen.
Follow directions of the screen.
* Set "Clock" first. (p. 24)
51