Operating Precautions - JVC WB-S681U Instructions Manual

Operating Precautions

For safety reasons special techniques are necessary for installation. Consult your dealer regarding installation, and ensure
that it is carried out by a specialist.
Be sure to mount the safety wire for safety purposes. If it falls, it may cause injury or accidents.
As the combination camera rotates at high speed, ensure that you install the camera at a location with sufficient strength to
support the vibration and weight. If the ceiling material is not strong enough, apply reinforcement materials such as plaster
board. If the reinforcement is weak or if the screws and nuts are not fully tightened, the vibration will cause fuzzy images on
the monitor screen and the screen may even fall off in the worst case. (For WB-S681U, WB-S682U, WB-S685U only)
Taking vibrations, mass and wind force into account, ensure to mount in a location with sufficient strength using solid
anchor bolts. If reinforced or spiral nuts are not tightened enough, picture blurring may occur on the monitor screen due to
vibration, and in the worst case there is a danger of falling.
Do not dangle or shake this unit, place or hook any objects on the unit. If too much load is placed on top, it may fall and
cause injury or accidents.
If a ball or bird hits this unit, bringing about some sort of trouble, consult your dealer or the nearest Victor service center.
Do not modify this unit yourself. Accidents may result.
Do not install in locations where there may be vibrations or impact. If it falls, it may cause injury or accidents.
Regularly check for the deterioration of attaching parts and the loosening of the screws caused by vibrations. If it falls, it
may cause injury or accidents.
Do not install the outdoor pendant mount (WB-S684U) at high locations of 16 m and above. Unexpected wind speed may
cause the pendant mount to fall and result in accidents.
The compatible cameras for each housing are as follows:
The suffix E of model No. specifies the exclusive variant for European market.
● WB-S681U, WB-S682U, WB-S685U: VN-V686U, TK-C686E (For Europe)
● WB-S684U: VN-V686WPU, TK-C686WPE (For Europe)
Do not brush your fingers against the metal edges. You may get hurt.
Inspect the camera regularly as rusty metals or screws will cause the camera to fall off and result in injuries or accidents.
Ask your dealer for inspections.
If there is any abnormality, stop using the camera, turn off the power immediately and contact your dealer.
Do not insert foreign objects into the camera. Water or metals in the camera will cause fire or electric shocks.
This equipment is intended for indoor use only. Do not use it outdoors or at places that are exposed to rain or moisture.
(For WB-S681U, WB-S682U, WB-S685U)
This unit may stop functioning properly due to natural hazards as it is to be installed outdoors. To take photographs
properly, be sure to perform daily checks.
This unit should be installed such that the camera is in a horizontal position. The unit will not function properly if the camera
is tilt or not in a horizontal position.
Do not place in the following locations.
This will result in malfunction or breakdown.
● Hot and cold places beyond the allowable operating temperature
● Humid places beyond the allowable operating humidity (20 % RH ~ 90 % RH) (Non condensing)
● Places with temperature exceeding the usage temperature
● Places with extreme temperature changes
● Places near devices such as transformer or monitor that emits strong magnetic waves
● Places near devices such as transceiver or mobile phone that emits radio waves
● Dusty and sandy places
● Places with vibration such as vehicles or ships
● Places prone to water droplets such as at the window (For WB-S681U, WB-S682U, WB-S685U)
● Steamy and oily places such as kitchens
● Special environments with combustible atmosphere
● Places that emits radiation, X-rays, corrosive gases or places where salt corrosion occur
● Places where medical agents are used such as pools
Do not install this unit in locations with sharp temperature changes, such as near air-con compressors or exhaust pipes.
Condensation may occur inside the attached combination camera.
To save energy, switch off the system when not in use.
During maintenance, make sure the screws for mounting the camera are securely fastened.