Panasonic Diga DMR-EX99V Operating Instructions Manual page 74

Changing the unit's settings
Signal Condition
You can check the quality and strength of digital broadcast signals.
The quality and strength of the
signal are shown.
Press [W X CH] to select the
channel.
When "Signal Condition" is
displayed in grey and cannot be
selected:
1 Press [EXIT] to exit the screen.
2 Press [W X CH] to select a digital channel. "D" appears on the
unit's display.
3 Display the Setup menu again (
Signal Quality
Below 2 (display red):
The signal quality is so poor that there may be interference in the
pictures and sound.
2–5 (display orange):
The signal quality is basically adequate, but brief interference in the
pictures and sound is possible in isolated case.
Over 5 (display green):
Optimum picture and sound quality.
Signal Strength
The display for signal strength is grey. "0" means signal strength 0%,
"10" means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your aerial.
≥When the signal is weak:
– adjust the aerial reception with "DVB Manual Tuning" in the
Setup menu ( 73).
– check that the current digital broadcast channel is correctly
broadcasting.
DVB Preferred Language
You can select up to 2 different subtitles and audio tracks to be
used when audio and subtitles of digital broadcasts are received.
Select the order of priority.
If the selected language is not available, then the language
included in the broadcast programme is selected.
Multi Audio
Multi Audio ( alternative )
[English] [German]
[Spanish] [Catalan]
[Corsican] [Original]
Subtitles
Subtitles ( alternative )
[English] [German]
[Spanish] [Catalan]
[Corsican] [Original]
The language specified as "Original" by the broadcast channel.
§
∫ Settings for Analogue Channels
Press [OK] to show the following setting.
Manual Tuning
You can delete analogue channels and set the analogue channel
details.
Manual Tuning
Pos Channel CH Pos Channel CH
1 ARD 4 11
2 ZDF 2 12
3 N3 5 13
4 HR3 8 14
5 BR3 10 15
6 16
7 17
SELECT
8 18
OK
9 19
RETURN
10 20
Delete
VQT2J46
74
[CH14] 5 BR3
Signal Quality 0
Signal Strength 0
RETURN
73).
[Italian] [French]
[Basque] [Galician]
§
[Italian] [French]
[Basque] [Galician]
§
To delete a programme position
Press [3, 4, 2, 1] to select a programme position and press the
"Red" button.
Note
≥This unit does not support SECAM L, L'.
10
10
To change the tuning settings for individual programme
+
Channel
–
Channel position
1 Press [3, 4, 2, 1] to select a programme position and press
[OK].
Pos
Manual
Channel
Tuning
CH
Fine Tuning
Video System
Mono
SELECT
Title Page
2 Press [3, 4] to select an item and press [1].
Pos
Programme position in the table
(You cannot change the programme position.)
Channel
To enter or change the Channel of a TV station
Press [3, 4, 2, 1] to enter station name and press [OK].
If the station name needs a blank space, select the blank
between "Z" and "¢".
CH
To enter newly available TV stations or change the CH
number of an already tuned TV station
Press [3, 4] or the numbered buttons to enter the CH number
of the desired TV station.
Wait a few moments until the desired TV station has been tuned.
After the desired TV station is tuned, press [OK].
Fine Tuning
To obtain the best tuning condition
Press [3, 4] to adjust the best tuning condition and press [OK].
≥Press [1] to return to "Auto".
Video System
To select the video system type
Press [3, 4] to select "PAL" or "SECAM" if the picture lacks
colour, and press [OK].
≥Auto
This unit automatically distinguishes PAL and SECAM signals.
≥PAL
For receiving PAL signals.
≥SECAM
For receiving SECAM signals.
Mono
To select the type of sound to be recorded
Press [3, 4] to select "On" if the stereo sound is distorted due
to inferior reception conditions, or if you want to record the
normal (mono) sound during a stereo, bilingual or NICAM
broadcast, and press [OK].
Title Page
To enter the Teletext title page for a channel
Entering title page number allows the unit to automatically record
programme and station names.
Press [3, 4] or numbered buttons to enter the number and
press [OK].
≥To find the correct title page for the station, refer to its Teletext
TV guide.
You can make the following two settings by selecting the external
input channel (AV1, AV2, AV3) in step 1.
≥Video System (Auto/PAL/SECAM)
In order to record properly, make the appropriate settings to match
the connected equipment.
≥Title Page (Auto/Off)
901
ARD
4
Auto
Auto
Off
301