Table of Contents
Advertisement
10. Reform both suction and discharge lines to
align with new compressor. If they are too
short, use additional lengths of tubing. Joints
should overlap 0.5" to provide sufficient area
for good solder joint. Clean and mark area
where tubing should be cut. Cut tubing with
tubing cutter. Work as quickly as possible to
avoid letting moisture and air into system.
11. Solder all connections according to soldering
procedure.
12. Remove original filter-drier.
CAUTION
D D O O N N O O T T u u n n b b r r a a z z e e o o l l d d f f i i l l t t e e r r - - d d r r i i e e r r f f r r o o m m s s y y s s t t e e m m . .
T T h h i i s s w w i i l l l l v v a a p p o o r r i i z z e e a a n n d d d d r r i i v v e e m m o o i i s s t t u u r r e e f f r r o o m m
d d e e s s i i c c c c a a n n t t b b a a c c k k i i n n t t o o s s y y s s t t e e m m . . T T h h e e o o l l d d f f i i l l t t e e r r - - d d r r i i e e r r
s s h h o o u u l l d d b b e e c c u u t t o o u u t t o o f f s s y y s s t t e e m m . .
13. Install new filter-drier at condenser outlet.
14. Evacuate and charge system using recom-
mended procedure described under
Evacuating and Recharging.
15. Reconnect compressor terminal leads in
accordance with refrigerator wiring diagram.
16. Reassemble unit.
R R e e f f r r i i g g e e r r a a t t i i o o n n S S y y s s t t e e m m
C C o o n n d d e e n n s s e e r r R R e e p p l l a a c c e e m m e e n n t t
NOTE
T T h h e e f f o o l l l l o o w w i i n n g g i i n n s s t t r r u u c c t t i i o o n n s s a a r r e e g g e e n n e e r r a a l l i i z z e e d d t t o o
h h e e l l p p t t h h e e t t e e c c h h n n i i c c i i a a n n u u n n d d e e r r s s t t a a n n d d t t h h e e p p r r o o c c e e d d u u r r e e s s
o o f f s s e e a a l l e e d d s s y y s s t t e e m m r r e e p p a a i i r r s s . . S S e e e e S S e e c c t t i i o o n n 5 5
C C o o m m p p o o n n e e n n t t T T e e a a r r d d o o w w n n o o n n t t h h e e e e x x a a c c t t s s t t e e p p s s o o f f
a a c c c c e e s s s s i i n n g g t t h h e e c c o o m m p p o o n n e e n n t t s s o o f f t t h h e e r r e e f f r r i i g g e e r r a a t t i i o o n n
s s y y s s t t e e m m . .
1. Disconnect electrical supply to refrigerator.
2. Remove compressor access panel.
3. Recover refrigerant by using EPA approved
recovery system.
4. Remove condenser fan mounting screws.
5. Unplug fan motor harness located in back of
fan motor.
6. Remove fan motor and fan blade.
7. After refrigerant is completely recovered,
disconnect inlet and discharge lines from
condenser.
8. Lift front of condenser and pull out of retainers
mounted to the drain pan.
9. Remove old condenser out the back of
cabinet.
10. Install replacement condenser.
11. Remove original filter-drier.
CAUTION
D D O O N N O O T T u u n n b b r r a a z z e e o o l l d d f f i i l l t t e e r r - - d d r r i i e e r r f f r r o o m m s s y y s s t t e e m m . .
T T h h i i s s w w i i l l l l v v a a p p o o r r i i z z e e a a n n d d d d r r i i v v e e m m o o i i s s t t u u r r e e f f r r o o m m
d d e e s s i i c c c c a a n n t t b b a a c c k k i i n n t t o o s s y y s s t t e e m m . . T T h h e e o o l l d d f f i i l l t t e e r r - - d d r r i i e e r r
s s h h o o u u l l d d b b e e c c u u t t o o u u t t o o f f s s y y s s t t e e m m . .
12. Install new filter-drier at condenser outlet.
13. Evacuate and charge the system using
recommended procedure described under
Evacuating and Recharging.
14. Reassemble unit.
4-7
Advertisement
Table of Contents
