Page 1: Table Of Contents
2002 Windstar Table of Contents Introduction Congratulations Safety and environment protection Symbol glossary Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo AM/FM stereo cassette (CD changer compatible) AM/FM stereo cassette with CD AM/FM stereo with CD Climate Controls...
Page 2 Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Traction control/AdvanceTrac Transmission operation Vehicle loading Trailer towing Recreational towing Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Jump starting Wrecker towing Customer Assistance...
Page 4: Introduction
State of California to cause cancer and birth defects or other reproductive harm. CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving it.
Page 5: Safety And Environment Protection
Introduction This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available. Remember to pass on the Owner’s Guide when reselling the vehicle.
Page 6 Introduction Protecting the environment We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.
Page 7 Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. By operating other electronic equipment (e.g. mobile telephone without exterior aerial) electromagnetic fields can occur which can cause malfunctions of the vehicle electronics. Therefore you should observe the instructions of the equipment manufacturers.
Page 8: Symbol Glossary
Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Tether Warning Anchorage Brake System Anti-Lock Brake System Brake Fluid - Traction Control...
Page 9 Introduction Vehicle Symbol Glossary Child Safety Door Power Window Lockout Lock/Unlock Interior Luggage Compartment Release Panic Alarm Symbol Engine Oil Engine Coolant Engine Coolant Do Not Open When Hot Temperature Avoid Smoking, Flames, Battery or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid...
Page 10: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES CHECK FUEL 4 5 6 TEMP H F FUEL TRAC BRAKE ACTIVE TRAC RPMX1000 THEFT km/h Some Warning Lights will show in the cluster equipped with a Message Center as words. Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs.
Page 11 Instrument Cluster without these or any other temporary malfunctions present, the light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required. If the light remains on, have your vehicle serviced at the first available opportunity.
Page 12 Instrument Cluster warning light does not illuminate as described, seek service immediately. Illumination after the parking brake is released indicates low brake fluid level or a brake system malfunction and the brake system should be serviced immediately by a qualified technician. Refer to Brakes in the Driving chapter for more information.
Page 13 Instrument Cluster Charging system Illuminates when the battery is not charging properly. Engine oil pressure Illuminates when the oil pressure falls below the normal range. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and specifications chapter.
Page 14 Instrument Cluster Bulb Warning Illuminates when one of the exterior bulbs has burned out. Low fuel Illuminates when the fuel level in the fuel tank is at, or near, empty (refer to Fuel gauge in this chapter for more information). Low washer fluid Illuminates when the windshield washer fluid is low.
Page 15 Instrument Cluster Anti-theft system Illuminates when the SecuriLock Passive Anti-theft System is armed. If the light fails to illuminate, continues to flash or remains on, have the system serviced. Turn signals Illuminates when the turn signals or the hazard lights are turned on. If the lights stay on continuously or flash faster, check for a burned-out bulb.
Page 16: Gauges
Instrument Cluster Key-in-ignition warning chime Sounds when the key is left in the ignition and the driver’s door is opened. GAUGES CHECK FUEL 4 5 6 TEMP H FUEL TRAC BRAKE ACTIVE TRAC RPMX1000 THEFT km/h Engine coolant temperature gauge Indicates the temperature of the engine coolant.
Page 17 Instrument Cluster Fuel gauge Displays approximately how much F FUEL fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel.
Page 18 Instrument Cluster Trip odometer Registers up to 1 600 kilometers (1 000 miles) of individual journeys. To display, depress the control. To reset, depress and hold the control for 2 seconds. To set back to odometer, depress the control again. Tachometer Indicates the engine speed in 4 5 6...
Page 19: Entertainment Systems
Entertainment Systems AM/FM STEREO PUSH SEEK TONE TONE VOL TUNE AM / FM STEREO AM/FM Your vehicle is equipped with a delayed accessory feature. This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off, or until a door is opened. Volume/power control Press the control to turn the audio PUSH...
Page 20 Entertainment Systems Bass adjust The bass adjust control allows you PUSH to increase or decrease the audio system’s bass output. TONE Press the TONE control once, then use the volume knob to adjust the desired level. Treble adjust The treble adjust control allows you PUSH to increase or decrease the audio system’s treble output.
Page 21 Entertainment Systems Seek function in radio mode • Press to find the next SEEK listenable station down the frequency band. TUNE • Press to find the next listenable station up the frequency band. AM/FM select The AM/FM select control works in radio mode.
Page 22 Entertainment Systems Setting the clock Press CLK to toggle between listening frequencies and clock TONE mode. To set the hour, press and hold the CLK control until CLOCK SET appears in the display and press the SEEK control: • to decrease hours and •...
Page 23: Am/Fm Stereo Cassette (Cd Changer Compatible)
Entertainment Systems Tune adjust in radio mode • Press to move to the next SEEK frequency down the band (whether or not a listenable TUNE station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 24 Entertainment Systems Volume/power control Press the control to turn the audio VOL - PUSH ON system on or off. Turn the control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 25 Entertainment Systems Tune adjust The tune control works in radio and CD changer modes (if equipped). Tune adjust in radio mode • Press to move to the next SEEK frequency down the band (whether or not a listenable TUNE station is located there). Hold the DISCS control to move through the frequencies quickly.
Page 26 Entertainment Systems Seek function for CD changer (if equipped) • Press to seek to the previous SEEK track of the current disc. If a selection has been playing for TUNE three seconds or more and you DISCS press , the CD changer will replay that selection from the beginning.
Page 27 Entertainment Systems 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. COMP SHUFFLE Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Page 28 Entertainment Systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. FADE Tape select • To enter tape mode while in radio or CD changer mode, press the TAPE control. • If no tape is found, NO TAPE TAPE appears in the display.
Page 29 Entertainment Systems CD changer select (if equipped) • To enter CD changer mode while in radio or tape mode, press the CD control. Rewind The rewind control works in tape and CD changer (if equipped) modes. To rewind in tape mode, press the SIDE 1 - 2 SIDE/REW control.
Page 30 Entertainment Systems To fast forward in CD changer mode, press the CD control. Press the control again to deactivate fast forward mode. Compression feature (if equipped) Compression adjust brings soft and COMP loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust.
Page 31 Entertainment Systems Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby ” and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode.
Page 32: Am/Fm Stereo Cassette With Cd
Entertainment Systems PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (CD CHANGER COMPATIBLE) DISC VOL PUSH ON FM 1 MUTE TAPE AUTO DOLBY B NR SEEK TUNE SCAN BASS TREB FADE SIDE 1-2 COMP SHUFFLE Your vehicle is equipped with a delayed accessory feature. This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off, or until a door is opened.
Page 33 Entertainment Systems If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. Bass adjust The bass adjust control allows you BASS TREB to increase or decrease the audio...
Page 34 Entertainment Systems Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted FADE between the front and rear speakers. Press the FADE control then press: •...
Page 35 Entertainment Systems Seek function for CD or CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
Page 36 Entertainment Systems AM/FM select in tape mode Press this control to stop tape play and begin radio play. AM/FM select in CD or CD changer mode (if equipped) Press this control to stop CD play and begin radio play. Radio station memory preset The radio is equipped with six station memory preset controls.
Page 37 Entertainment Systems Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the control. 3. When the first six strong stations AUTO are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset...
Page 38 Entertainment Systems To set the minute, press and hold the CLK control and press TUNE: AUTO • to decrease minutes and • to increase minutes. If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner.
Page 39 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 40 Entertainment Systems Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control rewinds the CD within the current track.
Page 41 Entertainment Systems Dolby noise reduction Dolby noise reduction operates in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the Dolby noise reduction. Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.
Page 42 Entertainment Systems Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow VOLUME MEDIA SEEK the rear seat passengers to operate the radio, tape, CD, or CD changer (if equipped). SIDE 1-2 COMP SHUFFLE To turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time.
Page 43 Entertainment Systems Plug a 3.5 mm headphone (not included) into either one of the two jacks. Press the control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed. A soft audible sound may be heard from the rear speakers. The front speaker will remain playing for the front passengers.
Page 44: Am/Fm Stereo With Cd
Entertainment Systems PREMIUM AM/FM STEREO IN DASH SIX CD RADIO DISC SHUF SCAN COMP SEEK TUNE MUTE LOAD BASS TREB FADE PUSH ON MENU Volume/power control Press the control to turn the audio system on or off. PUSH ON Turn the control to raise or lower volume.
Page 45 Entertainment Systems Bass adjust The bass adjust control allows you BASS to increase or decrease the audio system’s bass output. TREB Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Treble adjust The treble adjust control allows you BASS to increase or decrease the audio system’s treble output.
Page 46 Entertainment Systems Seek function in radio mode • Press to find the next listenable station down the frequency band. SEEK DOWN will display. • Press to find the next listenable station up the frequency band. SEEK UP will display. Seek function in CD mode •...
Page 47 Entertainment Systems AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play.
Page 48 Entertainment Systems Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autostore 1. Press and momentarily hold the AM/FM control. 2.
Page 49 Entertainment Systems Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 50 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 51 Entertainment Systems Load The load feature allows you to load single CDs into the player internal to the radio. This six disc CD player is equipped with a CD door. Compact discs should only be inserted into the player after the door has been opened by the player.
Page 52 Entertainment Systems If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF. Auto eject Press and momentarily hold the EJ control to engage auto eject.
Page 53 Entertainment Systems Menu mode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available.
Page 54 Entertainment Systems Radio data system (RDS) feature This feature allows your audio system to receive text information MENU from RDS-equipped FM radio stations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS feature is on, press the MENU control to scroll through the following selections:...
Page 55 Entertainment Systems Press the MENU control until FIND program type is displayed. MENU Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: •...
Page 56 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 57 Entertainment Systems RADIO FREQUENCY INFORMATION The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area.
Page 58: Climate Controls
Climate Controls HEATER ONLY SYSTEM (IF EQUIPPED) Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature.
Page 59 Climate Controls • (Floor) – Distributes outside air through the floor ducts. • (Floor and defrost) – Distributes outside air through the floor ducts and the windshield defroster ducts. • (Defrost) – Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. Operating tips •...
Page 60: Manual Heating And Air Conditioning
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) • without rear controls FRONT REAR REAR CTL • with rear controls Fan speed control Controls the volume of air circulated in the vehicle.
Page 61 Climate Controls Temperature Control FRONT REAR REAR CTL Controls the temperature of the airflow for the front part of the passenger compartment. Mode selector control The mode selector control allows you to adjust the direction of the airflow to the front part of the passenger compartment.
Page 62 Climate Controls • OFF-Outside air is shut out and the fan will not operate. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle. • (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts.
Page 63 Climate Controls 4. Turn the fan speed control to the position of your choice. During periods of high humidity, vapor may be emitted from the air outlets when using the A/C system with outside air. This can be corrected by using MAX A/C to cool the vehicle. Operating tips •...
Page 64 Climate Controls To aid in side window defogging/demisting in cold weather conditions: 1. Select the position that distributes air through the Panel and Floor. 2. Set the temperature control to full heat. 3. Set the fan speed to full fan. 4.
Page 65 Climate Controls The rear climate system fan speed control allows rear passengers to control the volume of air that is distributed from the rear registers. The temperature/mode selection control allows rear passengers to select the temperature, as well as whether the air is distributed from the overhead registers or the floor register, or a mix between the two.
Page 66 The filter is located just in front of the windshield under the cowl vent screen on the passenger side of the vehicle. For more information, or to replace the filter, see your Ford, Lincoln or Mercury Dealer.
Page 67: Lights
Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Autolamp control (if equipped) The autolamp system provides light AUTO sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Page 68 Lights High beams • Push forward past detent to activate. • Pull toward you past detent to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. Battery saver The battery saver will shut off the exterior lamps 10 minutes after the ignition switch has been turned off and the headlamp control is in the HEADLAMP position.
Page 69 Lights This control also has other features that are activated when any door is opened: • Rotate to full up position or next position (adjustment dial) to turn on all interior lights. • Rotate to first lower detent position to activate “sleeping baby mode”—...
Page 70 Lights 2. Measure the height from the center of your headlamp to the ground and mark a 2.4 meter (8 foot) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens.
Page 71: Turn Signal Control
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Dome lamps (if equipped) The front dome lamp is located overhead between the driver and passenger seats. The dome lamp will stay on if the control is moved to the passenger side position.
Page 72 Lights Map lamps (if equipped) The map lamps and controls are located on the dome lamp. Press the controls on either side of each map lamp to activate the lamps. Rear dome lamp The dome lamp lights when: • any door is opened (and switch is in middle position).
Page 73: Bulb Replacement
Lights BULBS Replacing exterior bulbs It is a good idea to check the operation of the following lights frequently: • Headlamps • Turn signals • Cornering lamps (if equipped) • Auxiliary parking lamps (if equipped) • High-mount brakelamp • Tail lamps •...
Page 74 Lights Function Trade Number Dome lamp Cargo liftgate lamp T-562 Map lamps/dome 578 (opt) Stepwell lamp T-562 Front seat footwell Front door mounted courtesy lamp Second row reading lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer. Replacing headlamp bulbs To remove the headlamp bulb: 1.
Page 75 Lights 5. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb. 6. Without turning, remove the old bulb from its socket by gently pulling it straight back out of the lamp assembly.
Page 76 Lights Replacing front parking/turn signal bulbs Note size and location of retainer pins for installation. 1. At the back of the headlamp, pull two retainer pins up to release the headlamp assembly. 2. Pull headlamp assembly forward disengaging the lamp from the rear retainer to expose the back of the bulb.
Page 77 Lights Replacing license plate lamp bulbs 1. Remove two screws and the license plate lamp assembly from the liftgate. 2. Remove bulb socket by pulling it straight out of the lamp assembly. 3. Carefully pull the bulb out from the socket and push in the new bulb.
Page 78: Driver Controls
Driver Controls WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
Page 79 Driver Controls Windshield wiper blades Check the wiper blades for wear at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild...
Page 80: Steering Wheel Adjustment
Driver Controls TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Page 81 Driver Controls Forward storage bins and conversation mirror (if equipped) The storage compartments may be used to store sunglasses or similar objects. The conversation mirror allows the driver to view the rear seating area. This does not replace your rear view mirror. Refer to Power Sliding Doors (PSD)(if equipped) in this chapter for operation of doors.
Page 82 Driver Controls • Place the provided height adaptors onto the back of the GARAGE control as needed. • Press the GARAGE control to activate the transmitter. Power Sliding Door (if equipped) The overhead console consists of the Power Sliding Door (PSD) ON/OFF control (with indicator light) and the right and left hand side PSD control(s).
Page 83 Driver Controls The sliding door must be unlocked for it to operate. The key does not have to be in the ignition. To help avoid accidental operation of the Power Sliding Door, disable the PSD second row passenger controls by pushing the overhead console control to OFF.
Page 84 Driver Controls Safety/Obstructions If anything obstructs the Power Sliding Door while it is closing, the door will automatically reverse to the open position, provided it meets sufficient resistance. Resetting the PSD The power sliding door may operate incorrectly or not at all because of the following condition: •...
Page 85: Power Windows
Driver Controls If you have the optional power sliding door, disable the power sliding door by pushing the ON/OFF control in the overhead console to the OFF position. The power sliding door cannot be opened from the rear seat when both this feature and the child lock are engaged. If you want to open the sliding door when the child safety lock is on: •...
Page 86 Driver Controls • Press the bottom portion of the rocker switch to open. AUTO One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. One touch down can be deactivated during operation by pushing down AUTO on the top part of the driver power...
Page 87: Mirrors
Driver Controls MIRRORS Automatic dimming inside rear view mirror (if equipped) Your vehicle is equipped with an inside rear view mirror which has an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror.
Page 88: Speed Control
Driver Controls Signal mirrors (if equipped) When the turn signal is activated, the appropriate mirror will show a blinking yellow arrow. When the park lamps are on, the blinking arrow will be dimmer. The arrow provides an additional warning to other drivers that your vehicle is about to turn.
Page 89 Driver Controls driving conditions permit you can return to speed control by pressing RES on the speed control. For more information on the AdvanceTrac system see AdvanceTrac Stability Enhancement System section in the Driving chapter. To turn speed control on •...
Page 90 Driver Controls If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RES will re-engage it. Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Page 91 Driver Controls To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Page 92 Driver Controls To return to normal overdrive mode, press the Transmission Control Switch again. The O/D OFF ON/OFF indicator light will no longer be illuminated. When you shut off and re-start your vehicle, the transaxle will automatically return to normal (Overdrive) mode.
Page 93 Cellport 3000–VR System. To avoid potential distraction and increased risk of injury or accident, Ford recommends you do not use the phone while driving. Please pull off the road and park before making or answering a call.
Page 94 When installed properly, the locator will not screw down tightly, but will rotate freely. Use only Ford original Equipment floor mats. Do not stack multiple floor mats over the Ford original equipment floor mats as they are not positively retained.
Page 95 Driver Controls federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink at: www.homelink.com or 1–800–355–3515.
Page 96 Driver Controls step 3 with procedures noted in the “Gate Operator and Canadian Programming” section for Canadian residents. 4. The red light will flash slowly and then rapidly. Release both buttons when the red light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmitters’...
Page 97 Driver Controls Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink button (note step 3 in the “Programming”...
Page 98 Driver Controls 3. Press and release the programmed HomeLink button. Press and release the HomeLink button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training.) The rolling code equipped device should now recognize the Homelink signal and activate when the Homelink button is pressed.
Page 99: Message Center
Driver Controls MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, km/h the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime.
Page 100 Driver Controls Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control to set the language choice. Units (English/Metric) 1.
Page 101 Driver Controls 5. doors closed (driver and passenger side). This message can only be reset by closing the door(s). If the RESET control is pressed, PLEASE CLOSE DOOR will be displayed. 6. rear liftgate status 7. exterior lamps (headlamps, front turn, brake, tail and cornering/side repeater lamp status) 8.
Page 102 Driver Controls “SPEED CONTROL CANCELLED” will be displayed when the brake pedal pressed. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds.
Page 103 Driver Controls Liftgate ajar Warning returns after the ignition key is turned from Low brake fluid level OFF to ON Check tail lamps Check headlamps Check rear turn lamps Check front turn lamps Check cornering/side repeater lamps (if equipped) Change oil soon Oil change required Check traction control (if equipped) Check advancetrac (if equipped)
Page 104 Driver Controls driving in a low gear at a high speed for an extended period of time. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the transmission fluid and level. Refer to Transmission fluid in the Maintenance and specifications chapter.
Page 105 Driver Controls contact your dealer for service as soon as possible. For further information, refer to AdvanceTrac stability enhancement system in the Driving chapter. CHANGE OIL SOON/OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed.
Page 106 Driver Controls 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. 4. Release the RESET control momentarily, then press RESET and SETUP controls at the same time to activate a service mode which will display OIL LIFE XX% RESET TO...
Page 107 Driver Controls Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone/calibration adjustment.
Page 108 Driver Controls 8. Press the RESET control to start the compass calibration function. 9. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CIRCLE SLOWLY TO CALIBRATE indicator changes to CALIBRATION COMPLETED. This will take up to three circles to complete calibration. 10.
Page 109 Driver Controls DIST TO EMPTY (DTE) Selecting this function from the INFO menu will give you an estimate of how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few kilometers (miles).
Page 110 Driver Controls Make sure that the liftgate door is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door open, keep the vents open so outside air comes into the vehicle.
Page 111 Driver Controls Utility hooks (if equipped) The utility hooks can be used to hang small items. Do not hang more than 12 kg (20 lbs.) on each of the hooks. The hooks are not designed to restrain objects during a collision. LUGGAGE RACK (IF EQUIPPED) Maximum load is 75 kg (165 lbs) on the roof rack structure, or 45 kg (100 lbs) on the roof panel, evenly distributed.
Page 112: Locks And Security
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLock Passive Anti-Theft System for more...
Page 113: Anti-Theft System
Locks and Security Childproof door locks When these locks are set, the rear sliding doors cannot be opened from the inside. The doors can be opened from the outside when the doors are unlocked. The childproof locks are located on front edge of each sliding door and must be set separately for each door.
Page 114 Locks and Security Unlocking the doors • 3–button remote • 4–button remote • 5–button remote Press this control to unlock the driver door and disarm the anti-theft system (if equipped). The interior lamps will illuminate. Press the control again within three seconds to unlock all doors and liftgate.
Page 115 Locks and Security Opening power sliding doors • 4–button remote • 5–button remote Press this control twice within three seconds to open the power sliding door (if equipped). The interior lamps will illuminate. Press this control another two times within three seconds to close the power sliding door and turn off the interior lights.
Page 116 Locks and Security Locking the doors • 3–button remote • 4–button remote • 5–button remote Press this control to lock all doors and liftgate, turn off the interior lights (if they were on) and arm the perimeter anti-theft system (if equipped). To confirm doors/hood are closed and locked, press the control a second time within three seconds.
Page 117 Locks and Security Sounding a panic alarm • 3–button remote • 4–button remote • 5–button remote Press this control to activate the personal panic alarm. The personal panic alarm will cycle the horn and turn signals on/off plus illuminate the interior lights. To deactivate the alarm, press the control again or turn the ignition to RUN or ACC.
Page 118 Locks and Security Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by: •...
Page 119 Locks and Security Replacing lost transmitters • 3–button remote • 4–button remote • 5–button remote If a transmitter has been lost or if you would like to purchase additional transmitters for your vehicle (up to four may be programmed into memory), take all your vehicle’s transmitters to your dealer or perform the reprogramming procedure yourself.
Page 120 Locks and Security rapid succession (within 10 seconds) ending in the ON position. After door locks lock/unlock, press any control on all transmitters (up to four). With each control press of the transmitters, the door locks should cycle (lock/unlock) to confirm programming. When completed, turn the ignition to OFF.
Page 121 Locks and Security Deactivating/activating the autolock feature The deactivating/activating the autolock feature can be turned off by the keyless entry pad (if equipped) on your door or by your dealer. Deactivating/activating the illuminated exit feature The illuminated exit feature can be turned off by your dealer. KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: •...
Page 122 Locks and Security 2. Press 1/2 control within five seconds of step one. 7 8 9 0 3. Press 1/2 control and hold for 2 seconds. The system will now only respond to the factory set code. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the 7 8 9 0...
Page 123 The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Automatic arming...
Page 124 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key. If your keys are lost or stolen you will need to do the following: •...
Page 125 Locks and Security Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience. The correct coded key must be used for your vehicle. The use of the wrong type of coded key may lead to a “no start”...
Page 126 Locks and Security If successful, the new coded key(s) will start the vehicle’s engine and the theft indicator will illuminate for three seconds and then go out. If not successful, the new coded key(s) will not start the vehicle’s engine and the theft indicator will flash on and off and you may repeat steps 1 through 6.
Page 127: Seating And Safety Restraints
Seating and Safety Restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 128 Seating and Safety Restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Page 129 Seating and Safety Restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Page 130 Seating and Safety Restraints The indicator light on the control will illuminate when activated. The heating of the seat turns off after 10 minutes or when the vehicle is turned off. Using the power lumbar support (if equipped) The power lumbar control is located on the inboard side of the seat.
Page 131 Seating and Safety Restraints REAR SEATS Head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 132 Seating and Safety Restraints Seat mounted cup holders (if equipped) Your vehicle may be equipped with cupholders mounted on the outboard sides of the second row seat(s). The cupholder is designed to detach from the seat when subjected to a heavy load. The cupholder can be reinstalled by lining up the arms with the side shield holes and pushing toward the seat.
Page 133 Seating and Safety Restraints • 2nd / 3rd row bench seat or 2nd row bucket console seat Pull control up to adjust seatback position. Pull control up to flip seatback to forward flat position. Accessing the 3rd row seat If your vehicle has an adjustable 2nd row bench seat or 2nd row bucket console seat, it can be adjusted to allow easier access to the 3rd row seat by sliding the seat forward, folding the seatback to the forward flat position, or using the recline control to adjust seatback forward.
Page 134 Seating and Safety Restraints If your vehicle has 2nd row bucket seats, it has an easy entry seat feature which allows ready access to the 3rd row seat. To access the 3rd row seat with 2nd row buckets: 1. Pull the seatback recline control up and allow seatback to flip forward.
Page 135 Seating and Safety Restraints Bench seat or Bucket Console seat To remove the seats: 1. (For 2nd row bench seat only.) Disengage the lap/shoulder belt from the side of the seat belt detach anchors (if equipped) by inserting the seatbelt tongue or a key into the slot in the detachable anchor and lifting upward.
Page 136 Seating and Safety Restraints 2. (For 2nd row bench seat only.) Using the clip attached to the end of the shoulder belt(s), clip the end of the belt to the stationary portion of the shoulder belt coming out of the trim panel. The end of the shoulder belt must be clipped in order to keep it from striking anything during vehicle operation.
Page 137 Seating and Safety Restraints To install the seat: 1. Remove (if necessary) tub covers from the floor to expose the seat mounts. • To remove the tub cover(s), use a screwdriver to pry the tub cover (where indicated) upward and out of the floor tub.
Page 138 Seating and Safety Restraints Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. Bucket seats To remove the seat(s): Position the seatback in the full down position to make removing the seat easier.
Page 139: Safety Restraints
Seating and Safety Restraints Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of air bag-related injuries.
Page 140 If your vehicle is equipped with this feature, there will be a label located under the front passenger seat which is marked “OCS”. Alternatively, you may take your vehicle to any Ford or Lincoln Mercury dealer for assistance. For air bags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the air bag when it begins to inflate.
Page 141 Seating and Safety Restraints Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 142 Seating and Safety Restraints Determining if the Personal safety system is operational The Personal safety system uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Warning light section in the Instrument cluster chapter. Routine maintenance of the Personal safety system is not required.
Page 143 Seating and Safety Restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 144 Seating and Safety Restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have locking cinch tongues described below: Safety belts with locking cinch tongue The locking cinch tongue will slide up and down the belt webbing when...
Page 145 Seating and Safety Restraints How to fasten the cinch tongue 1. Pull the combination lap and shoulder belt from the retractor so that the shoulder belt portion of the safety belt crosses your shoulder and chest. 2. Be sure the belt is not twisted. If the belt is twisted, remove the twist. 3.
Page 146 Seating and Safety Restraints Failure to replace the Belt and Retractor assembly after an accident could increase the risk of injury in a collision. Safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, front passenger and second row passengers.
Page 147 Seating and Safety Restraints Lap belts Adjusting the center lap belt The lap belt does not adjust automatically. The lap belt should fit snugly and as low as possible around the hips, not across the waist. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from).
Page 148 Seating and Safety Restraints Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning light buckled before the ignition switch illuminates 1-2 minutes and the is turned to the ON position... warning chime sounds 4-8 seconds.
Page 149 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare 36 700 crashes occur every day. The more events” we drive, the more we are exposed to “rare” events, even for good drivers.
Page 150 Seating and Safety Restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.
Page 151 Seating and Safety Restraints 4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps. 5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. • After step 5 the safety belt warning light will be turned on for three seconds.
Page 152 Seating and Safety Restraints a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage...
Page 153: Air Bags
This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles.
Page 154 Seating and Safety Restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag...
Page 155 Seating and Safety Restraints Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury.
Page 156 Seating and Safety Restraints A difficulty with the system is indicated by one or more of the following: • The readiness light (same light for front and side air bag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on.
Page 157 Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 158 Do not attempt to service, repair, or modify the air bag supplemental restraint system, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always...
Page 159 Seating and Safety Restraints How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.
Page 160: Child Restraints
Seating and Safety Restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with...
Page 161 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labeled as conforming to all applicable Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
Page 162 • Place seat back in upright position. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable...
Page 163 Seating and Safety Restraints of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps. Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 164 Seating and Safety Restraints 2. Slide the tongue up the webbing. 3. While holding both shoulder and lap portions next to the tongue, route the tongue and webbing through the child seat according to the child seat manufacturer’s instructions. Be sure that the belt webbing is not twisted.
Page 165 Seating and Safety Restraints 5. While pushing down with your knee on the child seat pull up on the shoulder belt portion to tighten the lap belt portion of the combination lap and shoulder belt. 6. Allow the safety belt to retract and remove any slack in the belt to securely tighten the child safety seat in the vehicle.
Page 166 Seating and Safety Restraints 5. Push down on the child seat while pulling on the loose end of the lap belt webbing to tighten the belt. 6. Before placing the child into the child seat, forcibly tilt the child seat from side to side and in forward direction to make sure that the seat is securely held in place.
Page 167 Seating and Safety Restraints Front passenger seating position (manual adjusting seats only) 1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. If the head restraint is adjustable, route the tether strap under the head restraint and between the head restraint posts.
Page 168 Seating and Safety Restraints 4. Rotate the tether hook, and clip the tether strap to the seat frame. If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision.
Page 169 Seating and Safety Restraints 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions. Rear seating positions Follow steps 1–8 as described above for the following available seats: • 2nd row bucket • 2nd row bench...
Page 170 Seating and Safety Restraints • 3rd row bench For additional important safety information on the proper use of seatbelts, child seats and infant seats, please read the entire Seating and safety restraints chapter in this owner’s guide. Attaching safety seats with LATCH (Lower Anchors and Tethers for CHildren) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle.
Page 171 Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Two plastic LATCH guides can be obtained at no charge from any Ford or Lincoln-Mercury dealer. They snap onto the LATCH lower anchors in the seat to help attach a child seat with rigid attachments.
Page 172 Seating and Safety Restraints If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
Page 173: Driving
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel.
Page 174 Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine.
Page 175 Driving 5. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns freely. This condition may occur when: •...
Page 176 Driving 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above –12° C (10° F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again.
Page 177: Brakes
Driving If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: •...
Page 178 Driving If you are driving down a long or steep hill, shift to a lower gear. Do not apply your brakes continuously, as they may overheat and become less effective. Anti-lock brake system (ABS) On vehicles equipped with an anti-lock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events.
Page 179 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up or remains on the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
Page 180: Traction Control/Advancetrac
Driving Push the button on the end of the parking brake and push the handle down as far as possible to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy.
Page 181 Driving If you should become stuck in snow or on a very slippery road surface, try switching the Traction Control system off with the traction control switch located on the left hand side of the radio. This may allow excess wheel spin to “dig”...
Page 182 Driving road conditions and/or when performing emergency maneuvers. In an emergency lane-change, the driver will experience better overall control of the vehicle. Driving conditions which may activate AdvanceTrac include: • taking a turn too fast • evasively maneuvering to avoid an accident, pedestrian or obstacle •...
Page 183 Driving During AdvanceTrac operation you may experience the following: • A rumble or clicking sound much like ABS or Traction Control • A slight deceleration or a reduction in the acceleration of the vehicle • The “TRAC ACTIVE” indicator light will illuminate •...
Page 184: Transmission Operation
Driving If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, the condition could be caused by any of the following: •...
Page 185 Driving If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with an automatic overdrive transaxle with column gearshift and O/D off switch Your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy.
Page 186 Driving P (Park) Always come to a complete stop and set the parking brake before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This locks the transaxle and prevent the front wheels from rotating. Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Page 187 Driving The transaxle will be in the “overdrive on” mode when the vehicle is started even if the O/D OFF mode was selected when the vehicle was last shut off. If the O/D OFF indicator light is flashing on and off repeatedly when the vehicle is started or does not come on when the O/D OFF control is pressed, it means that there is a transaxle electronic system malfunction.
Page 188 Driving 1 (First) Use 1 (First) when added engine braking is desired while descending steep hills. Manual downshifts to 1(first) can be obtained at speeds below 15 mph. The automatic transaxle will shift to the proper gear to ascend any grade without any need to shift to 1 (First).
Page 189 Driving The RSS will assist the driver in detecting certain objects while the vehicle slowly moves in reverse at speeds less than 4.8 km/h (3 mph). The RSS is not effective at speeds greater than 4.8 km/h (3 mph) and may not detect certain angular or moving objects.
Page 190: Vehicle Loading
Driving The indicator will remain illuminated to indicate a failure of the reverse sensing system. Always keep the sensors (located on the rear bumper/fascia) free from dirt, snow and ice (do not clean the sensors with sharp objects). These elements may cause the system to operate inaccurately.
Page 191 Driving • GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’s door pillar. • GCW (Gross Combined Weight): The combined weight of the towing vehicle (including occupants and cargo) and the loaded trailer.
Page 192: Trailer Towing
Driving your vehicle including both gross vehicle weight and Front and rear gross axle weight rating limits. Under no circumstance should these limitations be exceeded. Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Calculating the load your vehicle can carry/tow 1.
Page 193 Driving • Refer to the instructions included with towing accessories for the proper installation and adjustment specifications. If your vehicle is equipped with the optional heavy duty trailer tow wiring, it is pre-wired for trailer towing. An electrical connector is provided under the instrument panel for installing a customer-supplied electric brake controller.
Page 194 Driving Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch. You must distribute the load in your trailer so that 10% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to the hook retainers on the hitch.
Page 195: Recreational Towing
Driving Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. •...
Page 196 Driving ALL FRONT WHEEL DRIVE (FWD) VEHICLES An example of recreational towing is towing your vehicle behind a motorhome. The following recreational towing guidelines are designed to ensure that your transmission is not damaged. It is not recommended to tow front wheel drive vehicles with the front drive wheels on the ground. It is recommended to tow your vehicle with the drive wheels on a dolly or two wheel car hauling trailer.
Page 197: Roadside Emergencies
Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week •...
Page 198: Hazard Flasher Switch
1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673;...
Page 199 Roadside Emergencies The fuel pump shut-off switch is located behind the service panel on the right side of the cargo area. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2.
Page 200: Fuses And Relays
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
Page 201 Roadside Emergencies Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Page 202 Roadside Emergencies RELAY 1 RELAY 2 RELAY 3 RELAY 4 RELAY 5 RELAY 6 FUSE 1 FUSE 2 FUSE 3 FUSE 4 FUSE 5 FUSE 6 FUSE 7 FUSE 8 FUSE 9 FUSE 10 FUSE 11 FUSE 12 FUSE 13 FUSE 14 FUSE 15 FUSE 16...
Page 203 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description LH Power Mirror Motor, RH Power Mirror Motor, Adjustable Pedal Motor, Memory Module (if equipped) — Not Used Console Power Point Radio, Compact Disc Changer, Remote Keyless Entry Module, PSD (Power Sliding Door) Module RH and LH, Rear Seat Radio Controller (if equipped), Rear Seat Entertainment...
Page 204 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Electric Brake Controller, Brake Shift Interlock Solenoid, Rear Electronic Module Center High-Mount Stop Lamp Right Rear Turn Lamp, Left Stop Lamp, Left Rear Park Lamp Autolamp Sensor, Transmission Overdrive Cancel Switch, Front Electronic Module, Compass Module, Electrochromatic Mirror, Power...
Page 205 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Airbag Module, Passenger airbag deactivated indicator, Passenger Seat Weight Pressure sensor ECU — Not Used Cluster — Not Used Relay 1 — Switched System Power Relay #4 Relay 2 —...
Page 206 Roadside Emergencies The high-current fuses are coded as follows: Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 30A* Powertrain Control Module Relay 10A* Powertrain Control Module, Front Electronic Module 10A* A/C Compressor Clutch 25A* Horns, Horn Relay (coil) 15A* Fuel Pump Motor, Powertrain Control Module 30A*...
Page 207 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 15A* Left Front Park Lamp, Left Front Turn Lamp, Left Front Cornering Lamp, Left Front, Auxiliary Driving Lamp 15A* Left Headlamp (Low and High Beam) 10A* Alternator Field Sense 10A* Front Electronic Module (LH Door Lock Motor)
Page 208 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 30A** LH Power Seat Motors (if equipped), LH Power Lumbar Motor (if equipped), Driver Seat Memory Module (if equipped) 30A** Starter Motor Solenoid, Ignition Switch 30A** Delayed Accessory Relay, Delayed Accessory Relay (coil), Front Electronic Module, RHF Window Motor 50A**...
Page 209 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating — Not Used — Fuel Pump Relay — Not Used — Front Wiper Hi/Low Relay — Starter Interrupt Relay — High Speed Engine Cooling Fan Relay — Low Speed Engine Cooling Fan Relay —...
Page 210 Roadside Emergencies • tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle’s reduced ground clearance • try to repair the temporary spare tire or remove it from its wheel • use the wheel for any other type of vehicle Use of a temporary spare tire at any one wheel location can lead to impairment of the following: •...
Page 211 Roadside Emergencies Removing the spare tire To remove the spare tire: 1. Open the liftgate and open the plastic cover from the carpeting on cargo floor to expose the hex nut. On cargo van model, lift flap in mat to expose hex nut. 2.
Page 212 Roadside Emergencies If the vehicle slips off the jack, you or someone else could be seriously injured. 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF, and block the diagonally opposite wheel.
Page 213 7. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. If Ford Accessory Running Boards have been installed, use the jack adapters supplied with the running boards as described on the inside of the jack storage area.
Page 214: Jump Starting
Roadside Emergencies 9. Turn the jack handle clockwise until the wheel is completely off the ground. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack.
Page 215 Roadside Emergencies Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; also, the catalytic converter may become damaged. Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy.
Page 216 Roadside Emergencies Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Page 217 Roadside Emergencies carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery.
Page 218 Roadside Emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery.
Page 219: Wrecker Towing
It is recommended that your vehicle be towed by wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Page 220: Customer Assistance
Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 221 P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: • Your telephone number (home and business).
Page 222 5,000 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to...
Page 223: The Dispute Settlement Board
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford...
Page 224 • The name of the dealer(s) who sold or serviced the vehicle. • A brief description of your unresolved concern. • A brief summary of the action taken by the dealer(s) and Ford Motor Company. • The names (if known) of all the people you contacted at the dealership(s).
Page 225 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 226: Utilizing The Mediation/Arbitration
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 227: Ordering Additional Owner's Literature
U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S.
Page 228: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (or 366–0123 in the Washington D.C.
Page 229: Cleaning
Ph shampoo, such as Detail Wash (ZC-3–A), which is available from your authorized Ford, Lincoln or Mercury dealer. Always use a clean sponge or carwash mitt with plenty of water for best results. Dry the vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting.
Page 230 Minor scratches or paint damage from road debris may be repaired using the Ultra Touch Prep and Finishing Kit (F7AZ-19K507–BA), which is available at your authorized Ford, Lincoln or Mercury dealer. This kit contains: • Lacquer Touch-Up Paint (ALBZ-19500–XXXXA) •...
Page 231 Road Oil Removal (B7A-19520–AA). Use only approved products to clean plastic parts. These products are available from your authorized Ford, Lincoln or Mercury dealer. CLEANING WOOD-TONE TRIM Wipe stains with a clean, soft cloth and Ultra Clear Spray Glass Cleaner...
Page 232 Clean the outside of the windshield or rear window with a non-abrasive cleaner such as Ultra Clear Spray Glass Cleaner (E4AZ-19C507–AA), available from your authorized Ford, Lincoln or Mercury dealer. If after cleaning the glass surface, the water sheets from the glass (e.g., does not bead), then the window is clean.
Page 233 Extra Strength Upholstery Cleaner (E8AZ-19523–AA). CLEANING LEATHER SEATS (IF EQUIPPED) All Ford, Lincoln and Mercury vehicles with leather seating surfaces have a clear, protective coating over the leather. To clean the leather seats, simply use a soft cloth with Deluxe Leather and Vinyl Cleaner (F2AZ-19521–WA).
Page 234: Underbody Preservation
CLEANING AND MAINTAINING THE SAFETY BELTS Clean the safety belts with Extra Strength Upholstery Cleaner (E8AZ-19523–AA), available from your authorized Ford, Lincoln or Mercury dealer. Do not use bleach, dye or any other solvent to clean the belts, as these actions may weaken the belt webbing.
Page 235 Cleaning FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 236: Maintenance And Specifications
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 237: Hood
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
Page 238: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 1. Brake fluid reservoir 2. Air filter assembly 3. Power distribution box 4. Battery 5. Automatic transmission fluid dipstick 6. Engine oil dipstick 7. Engine oil filler cap 8.
Page 239: Engine Oil
In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specification ESR-M17P5–A. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 240 Maintenance and Specifications 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5.
Page 241 Maintenance and Specifications • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
Page 242 Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Page 243: Battery
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
Page 244 Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 245 Maintenance and Specifications 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Page 246 Maintenance and Specifications • Freeze protection down to -36° C (-34° F). • Boiling protection up to 129° C (265° F). • Protection against rust and other forms of corrosion. • Enables calibrated gauges to work properly. When the engine is cold, check the level of the engine coolant in the reservoir.
Page 247 The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44–A or yellow-colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS-M97B51–A1. To determine your vehicle’s coolant type (color), check your coolant reservoir. • Add Motorcraft Premium Engine Coolant (green-colored), VC-4–A (U.S.) or CXC-10 (Canada) or Motorcraft Premium...
Page 248 • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled engine coolant section). For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool.
Page 249 Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored). However, not all coolant recycling processes produce coolant that meets Ford specification ESE-M97B44–A.
Page 250: Fuel Information
Maintenance and Specifications • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months. If you drive in extremely hot climates: •...
Page 251 Maintenance and Specifications Automotive fuels can cause serious injury or death if misused or mishandled. Gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle.
Page 252 Maintenance and Specifications When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
Page 253 Maintenance and Specifications be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 254 Auto Makers’ Choice logo. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 255 Maintenance and Specifications Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver.
Page 256 Maintenance and Specifications • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles).
Page 257 Maintenance and Specifications • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs.
Page 258 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 259 Maintenance and Specifications Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 260 Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID • 3.8L OHV V6 engine Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
Page 261 MAX. Do not fill above this line. 4. Use only brake fluids certified to meet Ford specification ESA-M6C25–A. Refer to Lubricant specifications in this chapter. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used.
Page 262 Maintenance and Specifications TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes. Your transaxle does not consume fluid. However, the fluid level should be checked if the transaxle is not working properly, i.e., if the transaxle slips or shifts slowly or if you notice some sign of fluid leakage.
Page 263 Maintenance and Specifications The transmission fluid should be in this range if at normal operating temperature (66°C-77°C DON’T ADD IF IN CROSSHATCH AREA--CHECH WHEN HOT-IDLING [150°F-170°F]). High fluid level Fluid levels above the safe range may result in transaxle failure. An overfill condition of transmission DON’T ADD IF IN CROSSHATCH AREA--CHECH WHEN HOT-IDLING fluid may cause shift and/or...
Page 264 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 265: Low Tire Warning System
Maintenance and Specifications which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
Page 266 Maintenance and Specifications To reset the system, turn the ignition to the ON position, press Tire and hold the “TIRE RESET” switch Reset (located on the instrument panel behind the left side of the steering wheel) for three seconds. The low tire warning indicator light will flash three times as the low tire warning system begins to initialize.
Page 267 Maintenance and Specifications them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly, have them checked. • Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads.
Page 268 Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, “Touring”, etc.), as originally offered by Ford. Do not replace your tires with “high performance” tires or larger size tires.
Page 269: Part Numbers
4, 5, and 6 have a “E” suffix. If a spark plug needs to be replaced, use only spark plugs with the service part number suffix letter “EE” as shown on the engine decal. REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid...
Page 270 Washer Concentrate Use only brake fluids certified to meet Ford specifications. Refer to Lubricant Specifications in this chapter. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. Add the coolant type originally equipped in your vehicle.
Page 271: Lubricant Specifications
Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Ford part Ford part Ford name number specification Brake fluid Motorcraft High PM-1 ESA-M6C25-A Performance and DOT 3 DOT 3 Motor Vehicle Brake Fluid Door Silicone F7AZ-19G208-BA ESR-M13P4-A weatherstrips Lubricant F5AZ-19553-AA Engine coolant Motorcraft VC-4–A (in...
Page 272 Windshield Washer Concentrate Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. Ensure the correct automatic transmission fluid is used MERCON and MERCON V are not interchangeable.
Page 273: Engine Data
Maintenance and Specifications ENGINE DATA Engine 3.8L OHV V6 engine Cubic inches Required fuel 87 octane Firing order 1-4-2-5-3-6 Spark plug gap 1.3-1.4 mm (0.052-0.056 inch) Ignition system EDIS Compression ratio 9.36:1 VEHICLE DIMENSIONS Vehicle dimensions Wagon mm (in) Van mm (in) (1) Overall length 5 102.9 (200.9) 5 102.9 (200.9)
Page 274 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Page 275 Maintenance and Specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) 1.
Page 276: Accessories
Accessories FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln, Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 277 Accessories Engine block heaters Molded running boards Remote start system Seatback organizer Tire step Travel equipment Cargo organizer Console Factory luggage rack adaptors (Bike, ski, etc.) Framed luggage covers HomeLink (in sun visor) Inside rear view mirror with compass (with and without temperature display) Luggage/cargo basket Raised cross bars (roof rack)
Page 278 (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment.
Page 279: Index
Index Auxiliary power point ...85, 92 Axle ABS (see Brakes) .....178 lubricant specifications ..271 Accessory delay ......86 AdvanceTrac ......181 Air bag supplemental restraint Battery ........243 system ......153–154, 158 acid, treating emergencies ..243 and child safety seats ....155 charging system description ......154, 158 warning light ......13 disposal ........160 jumping a disabled battery ..214...
Page 280 Index Changing a tire ......209 Ford accessories for your vehicle ........235 Child safety restraints ....161 Ford Extended Service child safety belts ....161 Plan ..........222 Getting assistance outside the Child safety seats ......162 U.S. and Canada .....226 in front seat ......163 Getting roadside assistance ...197...
Page 281 Index check engine/service engine octane rating ....253, 273 soon light ........10 quality ........253 cleaning ........230 running out of fuel ....254 coolant ........245 safety information relating idle speed control ....243 to automotive fuels ....250 lubrication Fuses ........200–201 specifications ....271, 273 refill capacities ......269 service points ......238 starting after a collision ..198 Garage door opener ....81, 94...
Page 282 Index autolamp system .......67 bulb specifications ....73 Keyless entry system daytime running lights .....67 autolock ........120 flash to pass ......68 locking and unlocking doors ..122 high beam ......15, 68 programming entry code ..121 replacing bulbs ......74 Keys ........123–125 turning on and off ....67 key in ignition chime ....16 warning chime ......15 positions of the ignition ..173...
Page 283 Index safety belt .........12 traction control active ....13 Panic alarm feature, remote traction control off ....13 entry system ......117 turn signal indicator ....15 Parking brake ......179 Load limits .........190 GAWR ........190 Parts (see Motorcraft parts) ..269 GVWR ........190 Passenger Occupant trailer towing ......190 Classification Sensor ....140 Locks...
Page 284 Index Steering wheel controls ........80, 88 tilting .........80 Safety belts (see Safety restraints) ....15, 139, 142–146 Safety defects, reporting ..228 Tachometer .........18 Safety restraints ..139, 142–146 belt minder ......148 Temperature control cleaning the safety (see Climate control) ....58 belts .........151, 234 Tire warning ......265 extension assembly ....151 for adults ......143–145...
Page 285 Index Vehicle Identification Number Windows (VIN) ..........275 power .........85 rear wiper/washer .....78 Vehicle loading ......190 Windshield washer fluid and Ventilating your vehicle ...177 wipers checking and adding fluid ..239 checking and cleaning ....79 Warning chimes .....15–16 liftgate reservoir .....239 operation ........78 Warning lights (see Lights) ..10 replacing wiper blades .....79 Washer fluid ......239...

Ford 2002 Windstar User Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Driving

Roadside Emergencies

Customer Assistance

Cleaning

Maintenance and Specifications

Accessories

Index

Quick Links

Table of Contents

Related Manuals for Ford 2002 Windstar

Summary of Contents for Ford 2002 Windstar

Table of Contents