Related Manuals for Stanley HGE12
Summary of Contents for Stanley HGE12
- Page 1 HGE12 CORDLESS INLINE ROTARY GRINDER USER MANUAL Safety, Operation and Maintenance © 2014 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 73414 9/2014 Ver 3...
- Page 2 2 ► HGE12 User Manual...
-
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► HGE12 User Manual... -
Page 5: Safety
The term “power tool” in the warnings and safety g) If devices are provided for the connection of refers to the battery-operated HGE12 (cordless) rotary dust extraction and collection facilities, ensure grinder. these are connected and properly used. Use of dust collection can reduce dust-related hazards. - Page 6 Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: • ANSI Z87.1 eye protection (CAN/CSA Z94.3), • ANSI S12.6 (S3.19) hearing protection, • NIOSH/OSHA/MSHA respiratory protection. 6 ► HGE12 User Manual...
- Page 7 UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. HGE12 User Manual ◄ 7...
-
Page 8: Battery And Charger Safety
• Do not use an extension cord unless it is abso- RBRC™ is a registered trademark of the Recharge- lutely necessary. Use of improper extension cord able Battery Recycling Corporation. could result in risk of fire, electric shock, or electrocu- tion. 8 ► HGE12 User Manual... -
Page 9: Charger Safety
Removing the battery pack will red light remaining ON continuously. The pack is fully not reduce this risk. charged and may be used at this time or left in the • NEVER attempt to connect 2 chargers together. charger. HGE12 User Manual ◄ 9... - Page 10 Such batteries are still usable tery pack breaks or cracks, return to a service center but should not be expected to perform as much work. for recycling. The charger will indicate to replace battery pack. 10 ► HGE12 User Manual...
-
Page 11: Operation
This tool comes with a 1/4” collet. To COLLET change collets, remove the collet nut and insert the LOCK desired collet. Figure 3 WARNING: Make sure the switch is in the off position before removing or installing battery. HGE12 User Manual ◄ 11... -
Page 12: Maintenance
Stanley Hydraulic Tools, recommended accessories should be used with this product. If you need any assistance in locating any accessory, please contact Stanley Hydraulic Tools at 3810 SE Naef Rd, Milwaukie, OR 97267, (503-659-5660) and ask for a customer service representative also visit our website www.stanleyhydraulic.com. -
Page 13: Specifications
HGE12161B (Includes: Grinder with Battery, Charger, Bullnose Stone and BNSF Stone) Battery 18V and Charger 120V (P/N-73399) Battery 18V (P/N-73400) REPLACEMENT BITS Carbide Burr (1/4 inch Shank)..................73358 Bull Nose Stone 2 inch (1/4 inch Shank)................73052 Bull Nose Stone (BNSF) 2 inch (1/4 inch Shank).............66976 HGE12 User Manual ◄ 13... - Page 14 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267 503-659-5660 / Fax 503-652-1780 www.stanleyhydraulics.com...