Stanley Fatmax SFMCG400 Original Instructions Manual
  1. Manuals
  2. Brands
  3. Stanley Manuals
  4. Grinder
  5. Fatmax SFMCG400
  6. Original instructions manual

Stanley Fatmax SFMCG400 Original Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

4
1
6
2
7
5
3
www.stanley.eu
SFMCG400

Advertisement

Table of Contents
loading

Related Manuals for Stanley Fatmax SFMCG400

Summary of Contents for Stanley Fatmax SFMCG400

  • Page 1 SFMCG400...
  • Page 2 English (original instructions)

  • Page 4: Intended Use

    Intended use e. When operating a power tool outdoors, use an Your STANLEY FATMAX SFMCG400 angle grinder has been extension cord suitable for outdoor use. Use of a cord designed for grinding and cutting metal and masonry using suitable for outdoor use reduces the risk of electric shock.
  • Page 5 (Original instructions) ENGLISH f. Dress properly. Do not wear loose clothing or 5. Battery tool use and care jewellery. Keep your hair and clothing away from a. Recharge only with the charger specified by the moving parts. Loose clothes, jewellery or long hair can manufacturer.

  • Page 6: Kickback And Related Warnings

    ENGLISH (Original instructions) Never lay the power tool down until the accessory Operations for which the power tool was not designed has come to a complete stop. The spinning accessory may create a hazard and cause personal injury. Do not use accessories which are not specifically may grab the surface and pull the power tool out of designed and recommended by the tool manufacturer.

  • Page 7: Safety Warnings Specific For Grinding And Abrasive Cutting-Off Operations

    (Original instructions) ENGLISH Use special care when working corners, sharp edges When wheel is binding or when interrupting a cut for etc. Avoid bouncing and snagging the accessory. any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control complete stop.
  • Page 8 Chargers Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially Use your STANLEY FATMAX charger only to charge oak, beech and MDF.) the battery in the tool with which it was supplied. Other batteries could burst, causing personal injury and damage.
  • Page 9 (Original instructions) ENGLISH Mains plug replacement (U.K. & Ireland only) Charge discharged batteries within 1 week. Battery life will be greatly diminished if stored in a discharged state. If a new mains plug needs to be fitted: Safely dispose of the old plug. Charger LED Modes Connect the brown lead to the live terminal in the new plug.

  • Page 10: Hints For Optimum Use

    Note: Various trackwall hooks and storage configurations Allow the tool to stop rotating before laying it down. are available. Please visit our website www.stanley.eu/3 for Edge grinding with grinding wheels further information. Wheels used for cutting and edge grinding may break or kick back if they bend or twist while the tool is being used to do Fitting and removing the guard (Fig.

  • Page 11: Maintenance

    Maintenance A dust mask or respirator should be worn by all persons Your STANLEY FATMAX tool has been designed to operate entering the work area. The filter should be replaced daily over a long period of time with a minimum of maintenance.

  • Page 12: Protecting The Environment

    ENGLISH (Original instructions) Technical data Your charger does not require any maintenance apart from regular cleaning. SFMCG400 (H1) Warning! Before performing any maintenance on corded/ Voltage cordless power tools: Switch off and unplug the appliance/tool. Rated speed 9000 min- Or switch off and remove the battery from the appliance/ tool if the appliance/tool has a separate battery pack.

  • Page 13: Ec Declaration Of Conformity

    ENGLISH EC declaration of conformity Guarantee STANLEY FATMAX is confident of the quality of its products MACHINERY DIRECTIVE and offers consumers a 12 month guarantee from the date of purchase. This guarantee is in addition to and in no way prejudices your statutory rights.

  • Page 14: Accessory Chart

    ENGLISH (Original instructions) Accessory Chart Guard Type Accessory Description How to Fit Grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Wire wheels Backing flange Type 27 depressed centre wheel Locking flange Wire wheels with threaded nut Type 27 guard Wire wheel Wire cup with threaded nut...
  • Page 15 (Original instructions) ENGLISH Accessory Chart (cont.) Guard Type Accessory Description How to Fit Grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Type 27 Locking flange Guard...
  • Page 16 United Kingdom STANLEY FATMAX Tel. 01753 511234 270 Bath Road Fax 01753 572112 Slough, Berkshire SL1 4DX www.stanleytools.co.uk N717794 REV-01 11/2019...

Table of Contents