Canon iPF8000 series Service Manual page 277

Display massage
Cannot detect ink level 03810103-259D
correctly.
Close tank cover.
Cannot detect ink level 03810102-259E
correctly.
Close tank cover.
Cannot detect ink level 03810101-259F
correctly.
Close tank cover.
Cannot detect ink level 03810106-25A2
correctly.
Close tank cover.
Cannot detect ink level 03810106-25A3
correctly.
Close tank cover.
Cannot detect ink level 03810104-259C
correctly.
Close tank cover.
Paper jam. 03010000-2016
Manually rewind roll all the
way.
03010000-201A
03010000-201B
03010000-201C
03010000-201D
The paper is too small. 033200D2-2E30
Wrong paper type. 03864002-2E42
Hardware error. 03800500-2F47
03800500-2F47
Turn off printer, wait, then
turn on again.
Hardware error. 03800500-2F40
03800500-2F40
Turn off printer, wait, then
turn on again.
Hardware error. 03800500-2F41
03800500-2F41
Turn off printer, wait, then
turn on again.
Hardware error. 03800500-2F42
03800500-2F42
Turn off printer, wait, then
turn on again.
Hardware error. 03800500-2F43
03800500-2F43
Turn off printer, wait, then
turn on again.
Hardware error. 03800500-2F44
03800500-2F44
Turn off printer, wait, then
turn on again.
Hardware error. 03800500-2F2F
03800500-2F2F
Turn off printer, wait, then
turn on again.
Code* Condition detected
Subtank empty of C ink tank (ink tank cover opening
and refill ink tank usage)
Subtank empty of M ink tank (ink tank cover opening
and refill ink tank usage)
Subtank empty of Y ink tank (ink tank cover opening
and refill ink tank usage)
Subtank empty of MBK ink tank (ink tank cover
opening and refill ink tank usage)
Subtank empty of MBK2 ink tank (ink tank cover
opening and refill ink tank usage)
Subtank empty of BK ink tank (ink tank cover
opening and refill ink tank usage)
Cut sheet feed failure
Paper (right) edge detection error (cut sheet pick-up) Set or replace the media.
Paper (right) edge detection error (roll media pick-up) Set or replace the media.
Paper (left) edge detection error (cut sheet pick-up)
Paper (left) edge detection error (roll media pick-up) Set or replace the media.
Size clip error
Paper type mismatch
Head management sensor failure
The APCCHK signal of head management sensor is
out of range.
The non-discharge of all colors and chips (A/B,
EVEN/ODD) and nozzles is detected.
About all chips and nozzles of one color, the non-
discharge is detected.
About single line (A or B) and all nozzles (1280-
nozzles) of one color, the non-discharge is detected.
About single chip (A or B, EVEN or ODD) and all
nozzles (640-nozzles) of one color, the non-discharge
is detected.
The non-discharge of the EVEN or ODD line (640-
nozzles) is detected.
The non-discharge of the EVEN or ODD line (640-
nozzles) is detected the 320-nozzles or more.
Action
After the ink tank cover, replace the ink tank.
After the ink tank cover, replace the ink tank.
After the ink tank cover, replace the ink tank.
After the ink tank cover, replace the ink tank.
After the ink tank cover, replace the ink tank.
After the ink tank cover, replace the ink tank.
Check or replace a cut sheet.
Set or replace the media.
Confirm the print data.
Check the type of paper that can be fed and reload
the paper.
Check the head management sensor and
surrounding parts.
Replace the head management sensor.
Replace the main controller PCB.
Check the ink tube unit and surrounding parts.
Check the purge unit and surrounding parts.
Check the head management sensor and
surrounding parts..
Check the flexible cable unit and surrounding parts.
Check that the printhead is attached correctly.
Replace the head management sensor.
Replace the main controller PCB.
Replace the printhead.
Replace the carriage unit.
Check the ink tube unit and surrounding parts.
Check the purge unit and surrounding parts.
Check the head management sensor and
surrounding parts..
Check the flexible cable unit and surrounding parts.
Check that the printhead is attached correctly.
Replace the main controller PCB.
Replace the printhead.
Replace the carriage unit.
Check the head management sensor and
surrounding parts..
Check the flexible cable unit and surrounding parts.
Check that the printhead is attached correctly.
Replace the main controller PCB.
Replace the printhead.
Replace the carriage unit.
Check the head management sensor and
surrounding parts..
Check the flexible cable unit and surrounding parts.
Check that the printhead is attached correctly.
Replace the main controller PCB.
Replace the printhead.
Replace the carriage unit.
Check the head management sensor and
surrounding parts..
Check that the printhead is attached correctly.
Replace the main controller PCB.
Replace the printhead.
Replace the carriage unit.
Check the head management sensor and
surrounding parts..
Check that the printhead is attached correctly.
Replace the head management sensor.
Replace the printhead.
Chapter 8
8-13