Display Modes And Setting Changes/Adjustment Result Messages; Setting The Marker Displays; Setting The Camera Id - Panasonic AJ-SDX900E Operating Instructions Manual

CONTENTS
Chapter 4 Adjustments and settings for recording
4-7-4 Display modes and setting
changes/adjustment result
messages
By setting the display mode item, it is possible to select
various display methods for the changes made in the settings
and for the messages advising the user of the adjustment
results: for instance, the items displayed can be limited to a
select number or not displayed at all. To select the display
mode, perform menu operations to open the <VF DISPLAY>
screen from the VF page and select the setting for the DISP
MODE item.
For details on operation, refer to
Setting change/adjustment result messages and display modes
Situation in which message is displayed
When the filter selection has been changed
When the gain setting has been changed
When the WHITE BAL switch setting has been changed WHITE: n (n=ACH, BCH, PRESET)
When the OUTPUT/AUTO KNEE switch has been set
to AUTO KNEE or OFF
When the shutter speed/mode setting has been changed SS: 1/60 (or 1/120, 1/250, 1/500, 1/1000, 1/2000, S.SCAN)
When the white balance (AWB) has been adjusted
When the black balance (ABB) has been adjusted
When the extender has been selected
When a user button has been selected
When a marker select button has been selected
When in iris overwrite status
4-7-5

Setting the marker displays

ON, OFF or the display type can be selected for the displays
of the centre marker, safety zone markers, safety zone area
and frame marker. To make the selection, perform menu
operations to open the <VF MARKER> screen from the VF
page and select the display mode for each item.
For details on operation, refer to
operations."
#< VF MARKER >
TABLE
CENTER MARK
SAFETY ZONE
SAFETY AREA
FRAME SIG
FRAME MARK
FLAME LVL
<Note>
The MKR: A indication at the upper right of the screen shows
the display status. To check the settings for TABLE B, press
the MARKER SELECT so that MKR:B is displayed.
44
"4-6-2 Basic menu operations."
Filter: n (n=1, 2, 3, 4), m (m=A, B, C, D)
GAIN: n dB
(n= –3, 0, 3, 6, 9, 12, 15, 18, 21, 24, 27, 30)
AUTO KNEE: ON (or OFF)
Example) AWB A OK 3.2K
Example) ABB OK
Example) EXTENDER ON
Example) UM: S.GAIN 30 dB
Example) MKR: A
Example) ++ F 5.6
"4-6-2 Basic menu
MKR:A
:A
:1
:2
:90%
:4:3
:OFF
:15
#< VF DISPLAY >
DISP CONDITION
DISP MODE
VF OUT
VF DTL
ZEBRA1 DETECT
ZEBRA2 DETECT
ZEBRA2
LOW LIGHT LVL
ECU MENU DISP.
50M INDICATOR
MARKER/CHAR LVL
Message
4-7-6

Setting the camera ID

The camera ID is set on the CAMERA ID screen.
Up to ten alphanumerics, symbols and spaces can be used.
<Note>
The camera ID is not displayed while the setting menu is
displayed even if colour bar signals are output.
1
Perform a menu operation to open the <CAMERA ID>
screen from the OPERATION page.
#< CAMERA ID >
ID1 : ABCDEFGHIJ
ID2 : ABCDEFGHIJ
ID3 : ABCDEFGHIJ
2
Turn the JOG dial button to move the arrow (cursor) to
the "ID 1: to 3:" item.
:NORMAL
:3
:Y
:3
:070%
:085%
:SPOT
:35%
:OFF
:OFF
:50%
Display mode
setting
1 2 3
a a a a ± ±
a a a a ± ±
a a a a ± ±
a a ± ± ± ±
a a ± ± ± ±
a a ± ± ± ±
a a ± ± ± ±
a a a a ± ±
± ± : Message is to be
a a ± ± ± ±
displayed.
a a a a ± ±
a a : Message is not to
a a ± ± ± ±
be displayed.