Safety Instructions; General Safety Warnings - Husqvarna DM 230 Operator's Manual

General safety warnings

WARNING! Read all safety warnings and all
!
instructions. Failure to follow the warnings
and instructions may result in electrtic
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
Work area safety
• Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
• Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
• Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
• Do not use the machine in bad weather, such as dense
fog, rain, strong wind, intense cold, etc. Working in bad
weather is tiring and can lead to dangerous conditions,
e.g. slippery surfaces.
• Ensure when cutting that no material can become loose
and fall, causing operating injury. Take great care when
working on sloping ground.
• Always check the rear side of the surface where the drill
bit will emerge when drilling right through. Secure and
cordon off the area and make sure that no one can be
injured or material damaged.
Electrical safety
• Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is
earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase he risk of electric
shock.
• Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oli, charp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of cord suitable for
outdoor use reduces the risk of electric shock.
• Check that the cord and extension cord are intact and in
good condition. Never use the machine if the cord is
damaged, hand it in to an authorized service workshop for
repair.
6 –
English

SAFETY INSTRUCTIONS

• If operating a power tool in a damp location is
unaviodable, use a ground fault circuit interrupter
protected supply. Use of an GFCI reduces the risk of
electric shock.
• To avoid overheating do not use the extension cord while
it is rolled up.
• The machine should be connected to an earthed outlet
socket. Check that the mains voltage corresponds with
that stated on the rating plate on the machine.
• Ensure the cord is behind you when you start to use the
machine so that the cord will not be damaged.
WARNING! Do not wash the machine with
!
water, as water can enter the electrical
system or the engine and cause damage to
the machine or short circuit.
Personal safety
• Stay alert, watch what you are doing and use common
sense when operaing a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
• Use personal protective equipment. Always wear eye
protection. Protetctive equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
• Prevent unintentional starting. Ensure the switch is in the
OFF-position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in
unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure that these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
• Make sure that no pipes or electrical cables are routed in
the area to be drilled.
• Ensure the cord is behind you when you start to use the
machine so that the cord will not be damaged.
• Never leave the machine unsupervised with the motor
running. A rotating drill bit can entail a risk of serious
injury.
• Remain at a distance from the drill bit when the motor is
running.
• Always unplug the machine during longer work breaks.